How to wire the socket and how to wire the socket

The wiring method of the row socket is as follows:

Tools: Socket strips, screwdrivers.

1. First use a screwdriver to twist out Bu Wei's screws behind the socket row, and pay attention to put the removed screws well, so as not to lose them and find them.

2. Connect the live wire, connect the red live wire in the wire to the position of the switch, and some wires in the socket row are connected to each socket, so there is already a red wire at one end of the switch, and the new live wire can be connected on the other side of the switch.

3. Connect the zero line. Find the blue wire inside the socket and connect the new zero balance Zheng wire to the blue wire in it (connect it to the blue wire near the switch).

4. Connect the ground wire. The yellow and green wires you see in the socket row are the ground wires, and the ground wires in the wires can be connected to them.

5. If the wire of the socket is broken, and there is only the live wire and the neutral wire at home, then you only need to buy a plug back and connect the live wire and the neutral wire according to the above methods.

6. After the connection type is trained, the cover must be covered and the screws must be tightened to avoid leakage caused by other sundries inserted into it.

Precautions for wiring the row socket:

1. The corresponding neutral line and live line should be clearly distinguished to prevent some safety risks, and the safety of the operation process should be strictly guaranteed.

2. In the process of socket wiring, we should take the initiative to strengthen the protection of some safety measures to better ensure our own safety.

3. In the process of socket wiring, if necessary, professional people can guide the operation to achieve better results.

Use a screwdriver to unscrew the screws on the strip and keep them safe. Secondly, the red live wire in the wire should be connected to the switch position, the blue neutral wire inside the socket and the blue neutral wire in the wire should be connected together, and then the yellow and green ground wire inside the socket should be connected with the ground wire in the wire. Finally, install the screws that have been unscrewed back.

The specific operation steps are as follows: 1. Tighten the screws, first use a screwdriver to unscrew the screws on the socket row, and you need to keep the screws unscrewed to avoid loss. Because you still need to screw these screws back later.

2. Connect the live wire, and secondly, connect the red live wire in the wire to the switch position. Under normal circumstances, there will be wires connected to each socket on the socket, so one end of the switch is usually connected to the red live wire. The other end of the switch should be connected to the new live wire at the lift.

3. Connect the zero line, and then connect the blue zero wire inside the socket and the blue zero wire in the wire, that is, connect the blue zero wire with the blue zero wire around the switch.

4. Connect the ground wire, and then connect the yellow and green ground wire inside the socket and the ground wire in the wire. If the home appliance plugged into the plug bar needs to be plugged in frequently, then it is necessary to install a ground wire.

5. Tighten the screws, when the socket row has been wired, it is necessary to install all the screws that were unscrewed before to the original position, and be sure to tighten them, so as to avoid other items inserted into the socket row to cause leakage accidents.

The wiring method of the socket strip is as follows:

First, determine the position of the live wire (L), neutral wire (N) and ground wire (E) according to the wiring method marked on the strip. Typically, the live wire is located to the left of the socket, the neutral wire is located to the right of the socket, and the ground wire is located below the socket.

Insert one end of a wire into the live wire jack of the socket and the other end into the live wire of the wire.

Insert one end of a wire into the neutral jack of the socket and the other end into the neutral of the wire.

Insert one end of a wire into the ground jack of the socket and the other end into the ground wire of the wire.

Finally, insert the wires of other electrical appliances that need to be connected into the empty space of the socket strip, and connect the wires of the Queshan cover protection appliance to the correct position of the socket strip.

Note: During the wiring process, it is important to pay attention to calming the nerves and avoid touching the live wire and neutral wire to avoid electric shock accidents. At the same time, if it is found that the plug-in row is aging or damaged, it should be replaced with a new one.

First, remove the plug and put the plug backwards; Secondly, use a screwdriver to remove all the screws and put them away; Then you can see the colored wires that have been fixed; Then connect the red wire to the other side of the switch; Then connect the blue line and two-color wire to the zero and ground wires of the corresponding colors in turn; Finally, close the back cover and tighten the screws.

Note that before connecting the socket line, it is necessary to cut off the total power supply, and use a multimeter to detect whether there is live on the live wire. And when connecting the lines, pay attention to whether the colors of each line match, and it is strictly forbidden to reverse them.

Precautions for the use of electrical sockets

1. When using, we must pay attention to the power of the connected equipment, and the power connected to the equipment can not be greater than the rated value, otherwise it is easy to cause circuit danger, so the use of high-power equipment should be controlled when using the power strip.

When using, if you find that the wire is very long, you should untie it and stretch it, do not pile it together, and do not tie it up, so as not to cause danger after a long time when the wire becomes hot.

2. Before use, it should be determined that the plug of the equipment is fully inserted, so as to maintain the stability of the equipment, will not cause danger due to the current, and can also reduce the risk of electric shock.

In addition, if there are children at home, you must watch them, and you can't let the children dig the hole seat with their hands, and you can't water it, which will lead to damage to the plug and endanger personal safety.

Socket wiringTo open the housing of the socket strip, it is usually necessary to disassemble the socket with a screwdriver.

Remove the insulation of the power cord to reveal the wires inside. Connect the wires to the power cord binding posts on the socket strip separately, there will usually be three binding posts L, N, and E, which represent the live wire, neutral wire, and ground wire respectively. When connecting, you need to pay attention to fixing the wires on the binding posts, and ensure that the wires are firm and not loose.

Close the housing of the strip and fix the screws of the strip to ensure that the shell and wires of the strip do not loosen or fall off. It should be noted that the power switch needs to be turned off before wiring to avoid the risk of electric shock. At the same time, you need to read the instructions of the socket carefully when wiring to ensure that the wiring is carried out in the correct way.

If you are not sure if you are doing it correctly, it is recommended to ask a professional to wire it.

Precautions for using the socket

1. Choose the right socket: Choose the right socket type according to the number and power of the electrical appliances connected to ensure safety and stability.

2. Avoid overload: When connecting electrical appliances in the socket, care should be taken not to exceed the bearing capacity of the socket row to avoid overload.

3. Avoid humid environment: Avoid humid environment when using the socket to avoid leakage accidents.

4. Regular inspection: Regularly check whether the wires and sockets of the socket are damaged or aged, and replace or repair them in time.

5. Avoid long-term use: Avoid long-term use of the socket to avoid overheating or other safety problems.

6. Safe use: When using the socket strip, you should be vigilant to avoid the wire being stepped on or pulled to avoid electric shock accidents.

The steps for socket wiring are as follows:Tools Materials: Sockets, screwdrivers, wires.

1. We first use a screwdriver to unscrew the screws of the socket row and open the socket strip.

2. At this time, we can wire, generally the first is the live wire, the red wire in the wire is generally the live wire, connect it on the other side of the switch, and some of the wires in the socket are connected to each socket, so there are already red wires at one end of the switch.

3. Then connect the zero line, find the blue line in the socket, and connect the new zero line to the top zero line, which is also the round reed to the other end of the switch.

4. Then there is the grounding wire, the yellow or green one in the socket row is the ground wire, and the ground wire in the wire can be connected to it.

5. If the wire you bought back does not have a ground orange strip wire, then connect the live wire and the neutral wire.

6. After connecting the wire, cover the socket row, and tighten the screws. Prevent accidents.