How often does the lid under the sink sink get sucked up by water?

Because this is creating negative pressure. A small gap between the plug and the drain can be pried open with a suitable tool to eliminate it"After negative pressure, it will return to normal. If you feel inconvenient, you can change a vegetable basin and install the drainer.

Causes of clogged kitchen sinks.

1. The kitchen sink is clogged due to low temperature.

In autumn and winter, due to the relatively low temperature, the practical water in the kitchen is basically cold water, that is, the water we use to wash dishes, that is, the warm water for washing dishes, which cannot completely dissolve the oil stains.

2. The kitchen washing basin is clogged due to the structure of the washing basin.

Since many owners use double basin sewerage.

Pipe, there will be an anti-odor valve, after a long time, some large garbage in the washing basin will be stored in **, especially in autumn and winter, resulting in more and more serious blockage, and finally the water can not get out at all.

3. The kitchen sink is blocked due to the drainage pipe of the water trap of the vegetable basin.

In addition to the vegetable basin drain pipe is easy to block, there are also drainage pipes with water traps, especially small drainage pipes, which are more likely to be blocked by oil, which also occurs more often, and is also a more common way of blocking.

Through my analysis above, it can be seen that there are many nodes under the kitchen that are easy to be blocked by oil, mainly because many of us usually do not understand the correct use, resulting in the blockage of the sewer pipes.

How to unclog a clogged kitchen sink.

1. In autumn and winter, it is best to flush the sewer pipe with boiling water once every three or five days.

2. If it is not serious, you can use dredging agent or boiling water to flush it a few times.

3. If it is serious, remove it and clean it thoroughly, so that you don't have to worry about blocking it again.

4. If we really don't know how to deal with it, we can also ask professional people to help us dredge, so as to avoid messing up the pipe.

First of all, you need to clean all the water in the sink, put a basin under the sink, and then remove the water pipe so that the water in the sink can be drained completely. Then take a chopstick and poke the plug up from under the sink, loosen the screws at the bottom of the sink, and finally remove the head and reinstall it.

Sink installation precautions:

1. After the kitchen sink is installed, it is necessary to carry out a drainage test. Fill the sink with water first, and then pay attention to observe whether there is water seepage in the drainage area, and if so, it needs to be reworked immediately.

However, if there is no leakage after the drainage test, then the edge banding can begin, and when using silicone for edge banding, it is necessary to ensure the evenness between the gaps.

2. The installation position of the sink must be reserved in advance, so that the correct size can be provided to the merchant when purchasing to prevent errors in size. If there is an error in the size, there will be a phenomenon of left and right shaking after installation, and the firmness is very poor, and it is easy to fall off.

3. Before installing the kitchen sink, the debris in the water pipe must be cleaned up first, so as not to damage the valve core of the faucet by these sundries. When placing the sink on the countertop, a matching hanging piece must be installed between the countertop so that it can be installed securely.

The lid of your good friend's sink is sucked and can be easily opened with a pry bar.

The lid of the vegetable sink is sucked and cannot be opened, so you can find a place to let the air leak and let the air from the outside inside.

The bottom of my vegetable sink can be opened, and when I push it from below, the lid will be loosened You can see if you can open under your vegetable sink.

Drain the water and figure it out, of course. Remove the lid before you can do it. Settle.

Find a way to find a small thing, let the air in, and it can be opened.

Turn off the water, drain it, and you should be able to get it out of the side.

Hahaha! Capable man, loosen the lid.

Hello dear<> The sink lid is sucked and the solutions are as follows: 1First of all, you need to clean all the water in the sink, put a basin under the sink, and then dismantle the water pipe to remove it so that all the water in the sink can be drained. 2.

Then take a chopstick and poke the plug up from under the sink, loosen the screws on the macro part at the bottom of the sink, and finally remove the water head and reinstall it. Pro-<>

The two basins are sucked together mainly due to the negative pressure, and the two basins can be separated by the principle of thermal expansion and cold contraction.

Decision on the dismantling of the shirt:

1. You can use a knife to slowly pry open along the gap;

2. Add water between the two basins, and open it automatically through water infiltration;

4. It can be placed on the fire to be heated and expanded, and then separated;

5. Soak in the pool, use a knife or kitchen knife at both ends of the basin to gently pry it to separate;

6. Blow with a gas duct with high-pressure gas, and it will slowly separate.