How to install ceiling lamps on gypsum board ceilings

The ceiling lamp is installed on the gypsum board ceiling, and the installation bolts can not be difficult and easy to fall off, so I suggest that the method is to use extended expansion screws.

Directly penetrate the plaster ceiling and hit the ceiling.

Above. <>

First of all, there will be a keel in the gypsum board ceiling, and the general ceiling lamp is not particularly important, it is installed with a relatively small and lighter ceiling lamp, which can be directly fixed on the gypsum board with self-tapping nails. If Xilin's is a little heavier, you have to make a small hole in the gypsum board to see the dragon palace inside, and then fix it on the keel with self-tapping nails.

There will be a keel in the gypsum board ceiling, the general ceiling lamp is not heavy, if the installation is a relatively small and lighter lamp, you can choose to fix it directly on the gypsum board with self-tapping nails, a little heavier, to open a small hole (the ceiling lamp can be blocked), look at the keel inside, and fix it on the keel with self-tapping nails.

It is possible to make a hole in the gypsum board if its area permits, and add a piece of wood to the light steel keel to fix the lamp. You can also make an expansion bolt and add an iron wire to fix it.

1. Disassemble the lampshade and tube.

Ceiling lamps generally have a lampshade, and in order to prevent the lampshade from being damaged during installation, it must be removed along with the fragile lamp before installation, and finally installed after all other steps have been completed. It should be noted that different ceiling lamp shades are fixed in different ways, some are rotated and fixed, and some are snapped, so you must be careful when disassembling them to avoid damaging the lampshade.

2. Perforated gypsum board ceiling, although the material is not very hard, it has a good load-bearing, which is very convenient for you to perforate and install the ceiling lamp. Therefore, after removing the lampshade and tube, you can first put the base of the ceiling lamp in a predetermined position, mark it with pencil or chalk, and then take the base away and use an electric drill to punch holes in the mark. It should be noted that the diameter and depth of the hole drilled with an electric drill should be the same as the bolt specification used in the ceiling lamp.

The ceiling lamp should be perforated according to the specifications.

3. Install the base.

After the hole is laid, the expansion bolt should be installed in the hole, and then the base should be placed in the predetermined position, and the screw should be screwed into the bolt with a screwdriver, so that the base can be fixed. Considering the existence of deviation, after screwing the screws, check whether the position of the base of the ceiling lamp has deviated, and if there is, adjust it in time, so don't tighten it too tightly for the first time, so as to facilitate the adjustment of the base.

Dear, hello, I am happy to answer for you, how to install a panel light in a gypsum board ceiling A 1If the ceiling is installed where the keel is not installed, then just drill a small hole in the gypsum ceiling, and then take a carpentry board to fix it, and then install the chandelier. 2.

If it is a chandelier with a relatively large volume, it is best to install the expansion screw on the ceiling before making the gypsum hanger, and then use an electric hammer to make a hole in the top, install the expansion screw, connect the nut on it, and then install the chandelier. Gypsum board ceiling, flat lamp installation should leave the gypsum board, because the gypsum board fixed flat lamp is not firm and dangerous, so the gypsum board ceiling should leave space for the flat lamp, which is more suitable and safe, and there is no hidden danger.

In the gypsum board ceiling, it will have a keel, and the general ceiling lamp is not particularly important, is installed is a relatively small and lighter ceiling lamp, can be directly fixed on the gypsum board with self-tapping nails.

Make a few screw holes in the ceiling, install the LED panel light slide-in ceiling frame on the ceiling, slide the panel light into the fixed slide-in mounting frame, and then screw the fourth edge to fix the frame.

The surface of gypsum board is flat, and the board can be firmly bonded together through cementing material to form a seamless structure, and the architectural decoration effect is good.

The specific operation steps for installing the chandelier on the gypsum board ceiling are as follows:

1. Install the chandelier fixing bracket 5261 on the ceiling and tighten the screws on the left side.

2. Tighten the screw on the right side.

3. After the fixed bracket is installed, you can install the chandelier.

4. Connect the wires of the chandelier first.

5. Tighten the screws that fix the chandelier.

6. The installation is complete.

Here's how it works:

1. First of all, it is necessary to determine how much weight the chandelier is, and at the same time, it is also necessary to determine whether the gypsum board ceiling has been sealed and whether it has been brushed with latex paint.

2. Because the part of the lamp is to be fixed and connected to the base of the lamp plate, an independent boom is usually used with a light steel keel, a wooden keel, a blockboard or an independent boom. The weight of the chandelier determines the sturdiness, and the lamp panel cannot be installed directly on the gypsum board ceiling without reinforcement.

Generally speaking, heavy lighting, electric fans and other heavy equipment are strictly forbidden to be installed on the keel of gypsum board ceiling projects. It is still reserved for the boom fixed on the floor slab for installation. If the installation position of the chandelier happens to be a keel, it is best not to choose a chandelier that is too heavy, for the sake of insurance, fix a woodworking board on the gypsum board so that the load-bearing capacity of the gypsum board will be improved.

3. If there is no keel in the installation position of the chandelier, then you need to open a small opening on the ceiling surface of the gypsum board, and then put a piece of woodworking board to fix it, and then install the chandelier.

4. If it is a relatively large chandelier, it is best to fix the expansion bolt to the top surface of the ceiling in advance before making the gypsum board ceiling modeling, use an electric hammer to punch holes on the top, install the expansion screw, and connect the nut on the expansion screw rod to lengthen and install the chandelier.

If the installation location happens to have a keel, the weight of 2 catties is not a big problem to install on the keel, but it is best to fix a woodworking board on the gypsum board; If there is no keel in the installation position, then you can only make a small opening on the top surface, and then put a carpentry board on it and fix it, and then install the chandelier.

Don't listen to them, if the ceiling is ready, make a hole in the drywall, put an expansion screw with a hook on the roof, and hang an iron chain on the hook! Then seal the board back, and the chandelier will be hung on the chain.

Hehe, install it with **screws. There should be something to sell in the hardware store. Hope it helps.

It's a bit risky.

At the beginning, if you want to chandelier, you should use a light steel keel, and if you want to save money, you should also reinforce it.

2 catties is actually quite light, if the keel is a 300 * 300 painting, the lamp is installed nearby, it is reasonable to be able to load.

It may be better if it is mounted under the keel.

First of all, you have to pull the boom down from the cement on the floor slab and weld a steel frame to support it, otherwise the force is not good, and it is not safe!

If the lamp is heavier, you must first install the hook on the top plate, and then hang the chandelier rod through the gypsum board on the hook.

How to install small spotlights on the ceiling:

1. Turn off the power first, buckle the lamp slowly, pay attention to the spring clip on the lamp, and press down with your finger to take the lamp after seeing it.

2. Then disassemble the connector first, replace the lamp head, the driver does not move, turn on the light switch, if the light does not light up, you can determine that the driver is faulty, replace the driver.

3. It is best to turn off the main power supply, then dial the power inlet of the driver, then remove the bad driver and then dial the new driver power input section, and dial the two lamp wires.

4. Let one of the driver power cords be wound on one of the lamp power cords (the lighting electricity is not divided into positive and negative) and wrap it with electric tape, and the other one should be connected and wrapped with electric tape.

5. It is about to be completed, and then the power-on experiment will be turned on, and the switch light will be on.

Dig out the spotlight hole in the ceiling first, and then push the clip on the spotlight base up, and then push it up to get stuck.

About how to install small spotlights (also called ceiling lights) is actually the same as the installation of ordinary lighting, the only need to add transformers and lamp cups, in fact, these things please electrician masters to install on the line, if you want to install yourself, first of all, it must be connected to the transformer and lamp cup after the card slot is opened, stuffed into the open gypsum board hole, connected to the power supply OK!

It's stuck and has two springs

The ceiling lamp is installed on the gypsum board ceiling, the installation bolts can not be difficult, easy to fall off, my suggested method is to use the extended expansion screw to directly penetrate the gypsum ceiling, hit the ceiling.

Gypsum board is a material made of building gypsum as the main raw material. It is a kind of building material with light weight, high strength, thin thickness, convenient processing, sound insulation, heat insulation and fire resistance, etc., and is one of the new lightweight boards that are currently focused on development.

Gypsum board has been widely used in residential, office buildings, shops, hotels and industrial plants and other buildings of internal partition walls, wall cladding panels (instead of wall plastering layer), ceilings, sound-absorbing panels, ground base panels and various decorative panels, etc., for indoor should not be installed in bathrooms or kitchens.

The general ceiling lamp is not heavy, there will be a keel in the gypsum board ceiling, if the installation is a relatively small and lighter lamp, you can choose to directly use the self-tapping nail on the stone brigade bridge plaster board to fix. If it is a little heavier, you can open a small hole (the ceiling lamp can be blocked), see the keel inside and fix it on the keel with self-tapping nails, or you can make an expansion bolt and add an iron wire and fix it empty.

Ceiling lamp is a kind of lamp, as the name suggests, because the top of the lamp is flat, and the bottom is completely attached to the roof when installed, so it is called a ceiling lamp. There are ordinary white bulbs, fluorescent lamps, high-intensity gas discharge lamps, tungsten halogen lamps, LEDs, etc.

The ideas are as follows: 1. First of all, we must determine the weight of the chandelier, and also determine whether the gypsum board ceiling has been sealed and whether the latex paint is brushed. 2. Because the part where the lamp is installed should be connected to the base of the lamp panel, the independent boom is generally made of light steel keel, wooden keel, blockboard or independent boom.

The weight of the chandelier determines how strong it is. Without reinforcement, the light panel cannot be installed directly on the gypsum board ceiling. Generally speaking, it is strictly forbidden to install heavy equipment such as heavy lighting and electric fans on the keel of gypsum board ceiling projects.

Or pull out the boom fixed to the floor and install it. If the chandelier is installed in a position that happens to have a keel, it is best not to choose a bulky chandelier. To be on the safe side, fix a blockboard on the drywall so that the load-bearing capacity of the drywall will increase.

3. If there is no keel in the installation position of the chandelier, a small opening should be made on the ceiling surface of the gypsum board, and then fixed on a blockboard cavity, and then the chandelier should be installed. 4. If it is a relatively large chandelier, it is best to fix the expansion bolt on the top surface of the ceiling in advance before the gypsum board ceiling modeling, punch holes in it with an electric hammer, install the expansion screw, connect the nut on the expansion screw, and you can lengthen the chandelier. Hungry.