When the heating starts, how should the heating at home be adjusted?

He must have this one, the corresponding operating instructions, or will they send special people to teach you how to get it? It's dangerous to try it yourself.

Summary. 1. The central heating system is pressed, and the floor heating valve at home is open, which can ensure that the floor heating at home is pressed at the same time with the system, and ensure the safety and reliability of the system when it is running.

2. The pressure of the heating system at home, the main valve of the heating inlet and outlet and the mouth must be closed and disconnected from the central heating system, and all the valves on the water collector and distributor must be fully opened, so as to ensure the normal pressure of each heating circuit of the floor heating.

When opening the valve, turn the handwheel clockwise, turn the handwheel counterclockwise when closing, and rotate in place according to the opening and closing indication marks. The radiator can not change the position arbitrarily, nor can it release water from the system at will, because if the hot water is lost, the water temperature in the pipe network will decrease rapidly, resulting in a decrease in indoor temperature.

Open the manual bleed valve of each radiator to expel the air accumulated in the radiator, or open the exhaust valve of the gas collection tank installed on the top of the system to exhaust until each radiator is warmed up, the commissioning is complete, and once the commissioning is completed, the valve should be fixed and cannot be opened and closed at will.

Central heating debugging the radiators in the home to turn off or on.

Hello, it is necessary to open.

1. The central heating system is pressed, and the floor heating valve at home is open, which can ensure that the floor heating at home is pressed at the same time with the system, and ensure the safety and reliability of the system when it is running. 2. The heating system should be suppressed, the main valve of the heating inlet and outlet and the mouth must be closed and disconnected from the central heating system, and all the Hu Qianqing valves on the water collector and distributor should be fully opened, so as to ensure the normal pressure of each heating circuit of the floor heating. When opening the valve, turn the handwheel clockwise, turn the handwheel counterclockwise when closing, and rotate in place according to the opening and closing indication marks.

The radiator can not change the position arbitrarily, nor can it release water from the system at will, because if the hot water is lost, the water temperature in the pipe network will decrease rapidly, resulting in a decrease in indoor temperature. Open the manual bleed valve of each radiator to expel the air accumulated in the radiator, or open the exhaust valve of the gas collection tank installed on the top of the system until each radiator is warmed up, the commissioning is complete, and once the commissioning is completed, the valve should be fixed and cannot be opened and closed at will.

Do all radiator in and out switches have to be turned on?

Tomorrow there will be no one at home for commissioning.

1. It needs to be turned on during normal use. 2. The two valves of the heating system are dismantled and one is the return valve, and the other is the water supply valve, both of which are opened to form a water cycle, so that the heat energy transfer can be slowed down to each room to achieve daily heating. If one of the valves is closed, the hot water in the heating unit will not circulate properly and the temperature will drop.

3. Not only the main valve of the heating system and the main valve of the water supply should be opened, but also the return valve and water supply valve of each household need to be opened. If you feel that the temperature is too high when you use it, you can close one of the valves appropriately to reduce the indoor temperature.

Note 1Flush the pipes of the home radiator system.

First of all, the commissioning of the home radiator system is carried out after the installation of the gas wall-hung boiler equipment. Before we debug the home radiator, we should first clean the pipes of the heating system with high-pressure tap water, and try to wash out the sand and dust in the pipe due to the home radiator system accidentally getting into the pipe during construction, so as to take over and debug.

Note 2Home radiator system duct exhaust, pipe.

After flushing the pipes of the home radiator system, we need to exhaust the home radiator system by continuously injecting clean and bubble-free tap water with a certain pressure into the home radiator system, and then only open the water inlet valve of one radiator, turn off the water inlet valve of other radiators, and open the exhaust hole of the water inlet valve radiator to exhaust. Each radiator device needs to be repeated for the exhaust operation as above. After exhausting all the air in the pipes of the home heating system, we must take over the gas wall-hung boiler in strict accordance with the instructions.

For the part of connecting the gas wall-hung boiler to the natural gas pipeline, it is necessary to ask a professional gas master to install it, so as to ensure the air tightness of the gas pipeline and avoid safety problems.

Note 3Check the heating effect of the radiator.

After all the pipes of the home radiator system are properly connected, turn on or off the relative valve switch and then start the wall-hung boiler that carries the home radiator. Next, turn the temperature of all rooms to the maximum so that the home radiator can achieve the best heating effect in a short time. Check the radiator system as a whole for potential safety hazards and whether adjustments need to be made.

Finally, the sanitation and cleaning of the site were sorted out, and the construction site was restored to its original state.

First of all, check the status of the main valve of the heating pipe in your home, some of the older residential inlet and outlet valves have a main valve, there are two inlet and outlet valves, here we have to close the inlet valve and the outlet valve, and close the main valve of a pipeline.

Please click Enter a description.

Second, after closing all the valves, find the gas release valve that disturbs the radiator, generally a copper screw, and slowly unscrew it, because all the valves have been closed, so the gas pressure released by the gas release valve will not be too large, so that the gas in the channel will be released after opening, and the water in the radiator will naturally be kept at the bottom of the radiator.

Please click Enter a description.

Thirdly, you may feel the handling when unscrewing the copper screws, you can use tools, such as wrapping the front part of the screw with cloth to rotate, or use pliers to slowly unscrew it, and slowly open the water inlet valve when the gas in the radiator is discharged.

Please click Enter a description.

Fourth, in the state of opening the water inlet valve and closing the return valve, the water will be slowly filled with the radiator, observe who is flowing out of the air release valve and tighten the air release valve, pay attention to the whole water inlet process must be slow, and be patient when waiting for the water to be filled, only in this way can the gas in the radiator be better excluded, and the radiator is filled with water.

Please click Enter a description.

After all the radiators are filled with water, the exhaust valve is closed and then slowly open the water inlet valve, and then make sure that each corner of the radiator is filled with water, and pay attention to the valve switch to open small.

Please click Enter a description.

Sixth, after the radiator is filled with water, then slowly open the return valve, pay attention to be sure to open it slowly, stop when you hear the sound of running water, and ensure that the speed of the inlet valve is greater than the speed of the return valve, only in this way can the water be filled with the radiator.

Please click Enter a description.