How should the general paint be brushed better?

No, it should be brushed up and down, once from top to bottom, once in the back, not too much paint, it won't flow, that's what I do, hopefully.

First sandpaper sanding, and then brush a few times, generally 3 to 5 times is the best.

1. Pay attention to buy the kind of environmentally friendly paint, it is best to have diluted it, open it and use it directly, you can not be too impatient when brushing the paint, and you should brush it slowly in order to prevent bubbles.

2. Paint brushes, tape, long rods (the last two items are used to paint near the roof), masks, glasses (must be used when painting the roof).

3. Generally, it is brushed 3 times, and it is slowly dried after the first brush, and then brushed, dried, and dried.

4. Add a few more points: (1) When brushing, you must brush slowly, see if there are bubbles in the brushing place, and if there are bubbles, they will burst immediately; (2) When the brush is finished and waiting to dry, it should be cleaned with water immediately and soaked in water; (3) Masks and glasses must be worn, the former can reduce the inhalation of harmful gases, and the latter prevents paint from dripping into the eyes.

Kitchen cabinets, wardrobes, and shoe cabinets are generally painted, and paint is divided into two types: varnish (transparent paint that can reveal the background color) and paint (also called oil mixing).

To brush varnish, you need to buy primer, topcoat, sandpaper and colored putty, and you need to buy primer, putty (paint putty), topcoat, sandpaper or something to brush colored paint. The process of brushing paint is generally to brush the primer to close first, then fill the putty, polish, then brush the primer once or twice, and then polish, and then brush the topcoat after sanding, and then brush the topcoat after the last topcoat, and polish the filtered topcoat after polishing. The process of varnish and base paint is about the same, and it should be noted that the number of times to brush nitro paint is several times more than that of polyester paint.

The walls are generally painted with latex paint. Generally, you need to buy gypsum powder, putty powder, interface agent (construction glue), latex paint, roller, sandpaper, bandage (used for wall crack treatment) and so on. The process of wall treatment is generally:

First brush the interface agent to close the base of the original wall, then plaster caulking leveling, then scrape the putty 2-3 times, and then wait for the putty to dry and then polish, polish and brush the latex paint primer and topcoat.

It's best to hire a professional painter to do it for you, it's hard to get it yourself, after all, it's a new house, and the surface work of painting still has to be done.

Every time you get into trouble painting at home, I'll tell you a few tips on how to paint quickly.

Find someone who has just entered the industry to do it for you, just go low. Or do it yourself and do what you're asked. Where the requirements are not high. If you want to do something well, find a professional to do it. If you want to be economical, look at the surrounding **. I hope you are satisfied.

Kitchen cabinets, wardrobes, shoe cabinets, if you use solid wood (mountain wood) woodworking boards, use brushes... Brushed with a taste. Another waste of money.

The actual good brand on the wall is not a few dollars different from the bad brand... In the words of the standing gang. A 100 square house should cost around 3000-3500 yuan for materials.

I've just finished installing the house.

Do you have to find someone to do the renovation of your home one by one? The paint depends on whether it is brushed with clear oil or mixed with oil, and the wall is scraped putty first and then painted (wall paint).

Buy a brush or roller brush, and buy a few buckets of matching paint, and go to the home improvement store to ask.

Steps to paint:

1. Polishing. Second, scrape putty.

3. Brush the primer.

Fourth, the topcoat. 5. Polishing.

It's a very simple step, just like when you look for a carpenter, and then find a painter.

How to brush, what materials to buy, how much to buy, how economical, he will help you figure it all out. Of course, you have to find someone who is reliable.

Be mentally prepared, there are not many entries. You can refer to the keyiwenwo before one here safety first, first look at this mask, glasses must be worn, summer may be harder, the former can reduce the inhalation of harmful gases, the latter to prevent paint from dripping into the eyes.

First of all, it is necessary to clean the furniture, mainly considering the temperature and humidity, and dry it as soon as possible after brushing, otherwise the effect is not good.

1. Try not to mix water during the construction of medium and dark latex paint, which is easy to have color difference.

2. Bandages should be applied to the joints of gypsum board.

4. The original putty must be removed, or the glue can be brushed once.

5. Try to buy paint provided by famous paint brands.

Take a break and continue:

6. The air is too humid, don't paint, xiaoguo is not good.

7. The grinding of paint and coating should be carried out after it is completely dry.

8. The construction of the next paint must be carried out after the previous paint is dry.

9. The paint on the metal surface should be treated with anti-rust.

10. If the weather is too cold, the quality of paint construction will be poor. It's too hot, it's hard work, just bear with it.

Without? No, there are quite a few:

1. When painting the door, use masking paper to stick the hinges and door locks.

2. If the weather is too hot, pay attention to ventilation.

3. When pasting wallpaper, brush the oil on the wall, and remove the panels of switches and sockets at the same time.

Finally, one more article: bright and mercerized latex paint should be completed at one time, and it is easy to make up for color difference.

Also: after the baseboard is installed, make up the seams with putty and latex paint.

1. Check the surface of the wall, if there is any stain, wipe it with a mild detergent. If the old paint film is loose, it needs to be completely removed with a paint shovel.

2. If the wall is nailed or uneven, it needs to be filled with filler and polished smoothly.

3. Cover furniture, floors, doors and windows with old newspapers or instant adhesive tape to avoid contamination.

4. Wear gloves, protective clothing and hats.

5. Read the paint oil instruction manual in detail, dilute the paint oil according to the instructions and stir well.

6. Start with the ceiling, then the wall, and apply a layer of primer in the order from top to bottom.

7. Reapply two layers of paint to get the best effect.

8. The used tools should be cleaned as soon as possible.

9. The undiluted residual oil can be stored in a sealed container for later repair.

10. Do not pour the remaining paint into the drain casually, it will cause environmental pollution, you can pour the remaining paint on the old newspaper and wait for it to dry before discarding.

The advantages of good spraying are as follows:

1. Excellent surface quality. The paint sprayed on the wall forms a smooth, dense coating with no brush marks, which is incomparable to brushing and rolling.

2. High coating efficiency. The spraying efficiency of a single person is up to 350-550 square meters per hour, which is 10-16 times that of manual brushing.

3. Delay the life of the coating. High-pressure airless spraying, which uses high-pressure jet atomization, so that the paint particles can obtain strong kinetic energy to penetrate into the pores of the wall, so that the paint film and the wall form a mechanical occlusion, enhance the adhesion of the coating, and prolong the life.

4. The thickness of brush coating and roller coating is extremely uneven, generally between 35-200 microns, and the utilization rate is low. The airless spray coating has a uniform thickness, with a thickness of about 35 microns, and the utilization rate is high.

5. Corners and gaps can also be painted well. Because the paint spray does not contain air, the paint can easily reach these areas.

Brushing: The construction methods of latex paint painting are very backward, and brushes and rollers are generally used for construction. The result is:

1) Brush marks, hair removal, unevenness.

2) The glossy latex wall is matte.

3) The wall is easy to chalco.

The paint brushed will not destroy the paint film, the gloss is good, but the thickness is uneven, the paint sprayed is uniform, but the structure is destroyed, and the gloss is not high.

The best way to spray paint is to polish the oil.

At present, the best paint process is called airless spraying. It is the characteristic service of China Resources Paint.

In terms of spraying or roller coating or brushing. Or spray evenly, the surface effect is better!

Hello, you didn't say what kind of paint you painted that you painted. If it is wood paint (paint used on doors and wooden boards), it must be sprayed well, it is delicate, smooth, and has no brush marks; If it is a wall paint (latex paint), it feels good to spray, but the latex paint sprayed has a fatal drawback, and it cannot be repaired with a brush after spraying, let alone a roller. For the wall paint made by spraying, if you need to carry out local repair, you still need to spray it with a spray gun, otherwise it will leave obvious traces in the repair; If you use a roller brush, the effect is slightly worse than spraying, but it is easier to repair and will not leave marks.

Therefore, latex paint uses a roller brush more.

Roller coating and spraying are common latex paint construction methods. I don't think there is an obvious difference between the two, but I can only say that each has its own advantages and disadvantages.

Let's start with roller coating. Roller coating is a more traditional construction method, which has the advantages of simple construction, less waste, and textured film formation, and can also create different coating effects by changing the roller brush; The disadvantages are that it is prone to roll marks, it is difficult to control the final effect, and it is difficult to make a smooth and dense effect.

Let's talk about spraying. Spraying is developed with the popularization of airless spraying construction tools, and its advantages are that the effect is easy to control, the film formation is dense and smooth, and the construction speed is fast; Its disadvantage is that the waste is more serious (about 1 3 more than the roller coating), and the effect is relatively simple.

First, it is greatly affected by the state of the machine.

This depends on the situation, and I personally think it depends on at least the following points: 1. The completion effect; 2. Cost; 3. Personnel technical level; 4. Environmental conditions.

In terms of the finished effect, if the painting is done well, the smoothness, color uniformity, and uniform coating will be better than the painting, and the painting will be better than the brushing in any case, and there are still brush marks, etc., and it is possible that the color is uneven due to uneven coating.

In terms of cost, if you want to do a good job, the technical level required is relatively high, and the cost of equipped technical equipment is also higher, so the labor cost will be higher; However, if the painting is relatively speaking, it can better save paint, so if it is a large area that needs to be painted, if it is not the design requirements specified for painting, painting will basically be considered to save costs.

From the technical level of personnel, if the level of technical personnel is not good, spray paint is more likely to have uneven coating, uneven color, tear stains and other phenomena, which is not as good as the painting effect;

From the perspective of the painting environment, some environmental restrictions are not conducive to painting operations, because the smell of spray paint is very dispersed, and it is not easy to dissipate in a short time, and the floating paint particles have the opportunity to stick to other places in a large area, causing decoration damage, for example, the secondary decoration in the office is not very suitable for on-site painting.

If you spray it well, it is easy to make marks when the brush comes out.

Spray it, let's be more even.