How to deal with tile blurring? How to wipe the tiles so that they are not pasty

When cleaning tiles, be sure to choose a professional cleaner, if you choose the wrong cleaner, there will be a certain degree of corrosion of the tile. And do not use cleaning tools such as steel wool balls and stiff brushes when cleaning, as they will scratch the tiles.

Waxing can increase the waterproofness and stain resistance of tiles, and also reduce the bumps and friction of tiles to a certain extent. Expensive polished tiles and marble tiles are best waxed every 3 months, which can not only protect the tiles, but also keep the tiles shiny and new. Before re-waxing, the old wax must be cleaned up, the wax agent will turn yellow after a long time, if not removed, it will affect the brightness of the tile.

The mist of the tile after wiping it may also be because we did not clean it when we usually cleaned the tile, resulting in stains accumulating on the surface of the tile, so the tile loses its luster. When you clean the tiles, you can exchange water, white vinegar, soap powder, alcohol, and edible alkali according to a certain proportion, and then use it to wipe the floor tiles; Or we buy to use a special tile cleaner for cleaning.

If the pattern on the tile is vague and unclear, you can also lay it in a less important corner or under the bed, which will cover it up and not affect your overall senses.

How to deal with tile blurring? Personally, I think that in general, the blurred tiles like this are mainly because they are not very well drenched at 06, so it will lead to various blurred situations.

At present, there is no effective technology to repair the wear and tear of the tile surface, and the density of the tile is not high, which will be prone to scratches and bleeding. If the problem is too serious for you to accept, it is recommended to lay a wooden floor directly on it, about 2 cm.

The reasons why tiles are not clean and always blurry are as follows:1. If the wax layer on the surface of the tile is not cleaned, it will cause the surface of the tile to be dull.

2. The use of detergent is not suitable, and corrosion occurs, resulting in the loss of luster of the tile.

3. The glaze produces white mist and loses its luster.

4. Clean the tiles with hard objects, and use too much force, resulting in scratches.

tiles

Also known as tiles, it is a kind of acid-alkali resistant porcelain or stone formed by grinding, mixing, pressing, glazing and sintering through the process of grinding, mixing, pressing, glazing, sintering, etc., building or decorative materials, which are called ceramic tiles. Its raw materials are mostly mixed with clay, quartz sand and so on.

The surface of the tile is not glazed, and the material and color of the front and back are the same, hence the name of the whole brick. Full-body brick is a kind of wear-resistant brick, although there are varieties such as seepage bricks, but relatively speaking, the color of full-body bricks is not as good as glazed bricks. As interior design tends to be more and more plain design, all-over bricks are becoming more and more fashionable.

Full-body bricks are widely used in the floor of decoration projects such as halls, aisles and outdoor walkways, and are generally less used for walls, and most of the non-slip bricks belong to full-body bricks. Advantages: Due to the rough surface, the wear resistance and slip resistance are the best of all ceramic tiles.

Disadvantages: Its unique structure determines the texture and effect of the whole brick, and the decorative effect is poor.

Tiles that are not clean are always blurry, which may be due to the fact that the surface of the tiles is not cleaned properly, resulting in dull tiles. It is also possible that the cleaning agent used is not suitable, and corrosion occurs, causing the tile to lose its luster. It is also possible to use a harder object to clean the tile, which can cause scratches on the surface of the tile.

Ceramic tiles should be removed in time if there are stains infiltrated in daily life, and if stubborn stains are encountered, they need to be cleaned with professional cleaning agents.

Daily cleaning of tiles can be cleaned with dish soap, soap, etc. Use soap to add a little ammonia and turpentine to clean the cracked tiles, which can make the tiles more shiny.

If there are scratches on the surface of the tiles, you can apply toothpaste to the scratches and wipe them with a dry cloth to try to repair them.

If the tile surface is always blurry, it could be due to a number of reasons. Here are some of the reasons that can cause blurry tiles and how to fix them: Dirt or water stains on the surface of the tiles.

If there is dirt or water stains on the surface of the tile, it will make the tile blurry. The solution is to clean the tile surface with detergent and water, or use a steam cleaner to clean it. There are chemical residues on the surface of the tiles.

If a chemical-containing cleaner or other chemicals are used on the surface of a prepared hail tile, these chemicals may remain on the tile surface and cause the tile to become blurry. The solution is to use a specialized stain remover or cleaner, or have it cleaned by a professional cleaning company. There are scratches or abrasions on the surface of the tile.

If there are scratches or abrasions on the surface of the tile, these imperfections can also cause the tile to become blurry. The solution is to use abrasive tools to repair them, or to replace the tiles. There is a reflection of light on the surface of the tile.

Under certain light exposures, light bounces appear on the surface of the tile, causing the tile to become blurry. The solution is to replace the tiles or change the direction of the light. If the above methods do not solve the problem, it is recommended to consult a cleaning company or tile repair company for help.

Summary. Hello, here are a few good ways to clean your tiles:1

Use tile cleaners: There are many tile-specific cleaners on the market that can remove stains and dirt and make tiles clean and bright. 2.

Use vinegar and water: Mix white vinegar and water in a 1:1 ratio, pour into a spray bottle, spray on the tiles, and wipe clean with a damp rag.

3.Use baking soda and water: Combine baking soda and water at 1:

Mix the ratio of 3 into a paste, apply it to the tile, scrub it with a brush, and wipe it clean with a damp rag. 4.Use lemon juice and salt

Mix the lemon juice and salt, apply to the tiles, scrub them with a brush, and wipe them clean with a damp rag. 5.Use sodium hydroxide:

Mix sodium hydroxide and water, apply to the tile, scrub with a brush, and wipe clean with a damp rag. Note: Wear gloves and a mask when using sodium hydroxide, and avoid contact** and inhalation of gases. The above methods can be selected as needed to clean the appropriate method, but it is necessary to pay attention to safety when using it to avoid damage to the tiles.

Hello, here are a few good ways to clean your tiles:1Use tile cleaner:

There are many special tile cleaners on the market that can remove stains and dirt and make the tiles clean and bright. 2.Use vinegar and water:

Mix the white vinegar and water in a 1:1 ratio, pour into a spray bottle, spray on the tiles, and wipe clean with a damp rag. 3.

Use baking soda and water: Mix baking soda and water in a 1:3 ratio into a paste, apply to tiles, scrub with a brush, and wipe clean with a damp rag.

4.Use lemon juice and salt: Mix lemon juice and salt, apply to tiles, scrub with a brush, and wipe clean with a damp rag.

5.Using sodium hydroxide reeds: Mix sodium hydroxide and water, apply to the tile, scrub with a brush, and wipe clean with a damp rag.

Note that when using sodium hydroxide, wear gloves and masks, and avoid contact** and snuff into the gas. The above methods can be selected as needed to clean the appropriate method, but it is necessary to pay attention to safety when using it to avoid damage to the tiles.

I have helped you find the results;

The reason why the floor tiles are not clean and there is always a layer of fog may be because there are oil stains on the surface of the tiles.

There is always a layer of fog when the floor tiles are not clean, it may be because the floor tiles are covered with a layer of oil stains, and you can pour an appropriate amount of dish soap and detergent into the water when mopping the floor, which can play a role in removing oil stains. Or add an appropriate amount of baking soda for mopping, which has a better decontamination effect, and the floor is not easy to have dust after mopping.

When the floor tiles are just paved, it is best to brush a layer of waterproof coating with a brush at their joints or cracks to prevent black and mildew in the future. After the kitchen floor tiles are paved, they can be coated with a layer of candle oil or a layer of oil-proof stickers, which has the effect of beautifying the seams and preventing the gaps from hiding dirt and dirt.

Classification of tiles

Ceramic tiles are divided into polished tiles, vitrified tiles, glazed tiles, antique tiles, ceramic mosaic tiles, and full-body tiles according to the process. Polished brick is a kind of bright brick made by grinding and polishing the surface of the whole brick body, which belongs to a kind of whole body brick.

Vitrified bricks, made of quartz sand, mud fired in a certain proportion, and then polished but do not need to be polished, the surface is as smooth and translucent as a glass mirror, is the hardest of all ceramic tiles, glazed bricks are glazed on the surface of the embryo body firing. The main body is divided into two types: pottery and porcelain. The back of the clay fired is red, and the back of the porcelain clay fired is grayish-white.

Antique bricks, not the products of China's ceramic industry, antique bricks first originated from the glazed bricks in Europe, and then to China, also known as pan-ancient bricks, and then called classical bricks, retro bricks, antique bricks.

Ceramic mosaic tiles, also known as mosaics, have many specifications, thin and small, hard texture, acid resistance, alkali resistance, wear resistance, water seepage, strong pressure resistance, not easy to break, diverse colors, and a wide range of uses. All-over brick, which is an unglazed porcelain tile that has good slip resistance and wear resistance. Due to the moderate price of this kind of brick, it is quite popular with consumers.

Ceramic tiles may be used in the process of improper use is easy to cause surface staining, and several common staining treatment methods are as follows:

1. Use sodium hypochlorite dilution (bleach) for tea stains, fruit stains, coffee, sauce vinegar, leather shoe prints and other stains, soak them for 20-30 minutes and wipe them off with a cloth; Some stains that have been infiltrating the brick for a long time can be soaked for several hours.

2. Mildew spots formed by mildew of ink and antifouling wax, use sodium hypochlorite dilution (bleach). To use, simply apply bleach to the stain and soak it for a few minutes to wipe it off.

3. Use hydrochloric acid or phosphoric acid solution for cement, scale, rust and rust spots, and wipe it several times.

4. Use alkaline detergent or organic solvent (and 5 ketones, triethylene) to remove paint and degreasing agent for paint, oil, oily marker, and surface antifouling wax layer.

5. How to use glue hammer mark decontamination: first soak in 20%-40% sodium hydroxide solution for 24 hours and wipe it with a cloth, and then soak it in 30%-50% hydrochloric acid solution for 30 minutes and wipe it with a cloth.

6. Use alkaline detergent for ice cream.

7. Use acidic detergent for limescale.

Remarks: 1. Rubber gloves need to be worn when using the above detergents.

2. After the stain is removed, the brick surface is scrubbed clean with water.

3. There is the latest decontamination detergent in the market or supermarket, you can refer to the above decontamination range and method.