How to remove the sponge mop head, how to change the mop to the sponge head

Here's how to remove the sponge mop head:1. The structure of the absorbent mop is similar, and there are four screws on the sponge head of the absorbent mop.

2. The screw is responsible for fixing the sponge head on the roller.

3. These four screws need to be found before replacing the sponge head.

4. Use a screwdriver to remove the screws, and then slowly pull the sponge off the roller.

How to remove the sponge mop head from the card slot

You can see that there are 4 screw holes on it, and the spacing between them is a certain standard, you only need to loosen the screws through a screwdriver, replace the original old sponge head, and then replace it with a new one, we can mark it according to it, if it is the word in, you need to push it slowly and forcefully, so that you can replace the new sponge mop head successfully.

What to pay attention to when mopping the floor

When we mop the floor, we should first clean the floor and then mop the floor, which can avoid the problem that the mop will become very dirty after a while, and the problem of cleaning and changing the water will save us time and energy when mopping the floor in the later stage.

When cleaning the floor, we can use vacuum cleaners, sweeping robots and other tools to clean the dust and dirt on the ground.

When we mop the floor, we should pay attention to the choice of detergent, we don't just mop the floor with water, we can add some baking soda and white vinegar to the water, so that mopping can have a good decontamination and sterilization effect, or we can use rice water to mop the floor, add dish soap to the water, etc., can also play a good decontamination effect, you can also consider adding some salt to the water, which can make the floor dry faster.

Here's how to change the mop sponge head:Operating tools: mop, sponge head.

1. First prepare the sponge mop head for installation. When buying a mop, it depends on the size, and the vast majority of mop heads can be universal, but it is not excluded that they cannot be used.

2. Check the back of the seaside mop head, there are a total of 4 buckles, if any buckle is broken, the sponge mop is not so firm.

3. Use a small driver to pry the buckle on the front of the mop head, and then push it hard, and the buckle will be released.

4. Next, let's talk about how to install the sponge mop head, first align it with the position as shown in the figure below.

5. Slide the sponge head, put the buckles one by one, and hear a clear "pop" sound on behalf of the buckles are stuck.

6. The last brand new sponge mop head is replaced.

Here's how:Tool required: Screwdriver.

1. Get ready for a new sponge that needs to be better. This sponge has a layer of plastic that is used to moisturize.

2. Take out the mop rack, check the screw holes installed on the mop sponge and the mop frame, and remove the screws.

3. Put the removed screws away and use them later.

4. Tear off the protective plastic on the sponge.

5. Put the sponge and the mop rack together and compare the installation position.

6. Install the sponge and the mop holder together and tighten them.

When you want to remove the old sponge mop head, first use a Phillips screwdriver to unscrew the screws on one side, unscrew the screws on one side of the sponge mop head, and then use the same method to remove the two screws on the other side.

When the screws on both sides are removed, the original sponge mop head can be removed, and the new mop head can be replaced, pay attention to the position of the screw hole of the new sponge mop head should be consistent with the original one, and then align the hole of the new sponge mop head with the hole on the mop pull bar, and tighten it.

Precautions for the use of sponge mops.

Use a sponge mop to mop the floor, as this sponge dries easily, you need to prepare a basin or pool of water to soak the sponge mop in beforehand. Wait until it is completely soaked, then squeeze the mop dry, mainly to squeeze the sponge dry before mopping the floor.

When mopping the floor, drag it out of the room, clean the sponge mop, and keep squeezing the sponge when cleaning, and then mop the floor again. So repeatedly, wait until the ground is mopped, finally clean the rubber wool mop, soak it in the solution, you can add baking soda and white vinegar, the surface stains are cleaned, and finally put it under the faucet to rinse it several times, squeeze out the water, and put it in a cool place to dry for the next use.

Dear, I'm glad to answer for you: how to put the mop sponge back when it falls A: dear, the mop replacement sponge head is also relatively simple, first of all, there is a clip at the bottom of the mop, we only need to break the clip, we can take off the old sponge head, and then install the new sponge head, although the replacement method is very simple and scattered, but you must pay attention to your own strength when operating, because the clip is generally plastic, if the strength is relatively large, it is easy to cause damage to the clip, At that time, you will have to buy a new mop.

In fact, now as long as you buy the products of large manufacturers through regular channels, the general manufacturers are equipped with manuals, and I only need to operate according to the instructions.

Extruded sponge mop head replacement method:

First use a screwdriver to remove the screws on both sides of the sponge mop head, and then remove the sponge mop head, and replace it with a new mop head.

Specific method: 1. First find the position of the screw that fixes the sponge head, use a screwdriver to unscrew the screw, if the screw is rusty, you can drip some cooking oil to unscrew it. 2. After unscrewing the screws on it, you can remove the sponge head.

3. Unpack the new sponge head, align the rod and the screw hole, and then fix the screws in order, and the mop head will be replaced.

Maintenance of sponge mop

1. After use, the sponge mop should be soaked and cleaned with disinfectant water in time, and then placed to dry, and then placed in a dry corner, which can effectively kill bacteria.

2. The sponge mop is not suitable for exposure to the sun, otherwise it will affect the secondary use, resulting in the weakening of the sponge mop's effect on absorbing water stains, which is not conducive to the maintenance of the mop.

3. And after the use of the sponge mop, the mop head should be placed upwards, for the health of the family and the smooth use of the mop, the sponge burial mop should be replaced in time after two or three months of use, and do not use the sponge mop to drag the heavy oil stained area, which will reduce the time of its use.

Summary. Hello dear, I'm glad to answer for you, 1. Disassemble the sponge head.

The sponge head of the folded sponge mop is stuck on the pallet. We can insert a slotted screwdriver into the gap between the mop and the sponge head, and use the screwdriver to push the sponge head out forcefully, and then we can remove the buckle of the sponge head from the card slot of the pallet and remove it. Or we put on gloves, hold the mop in one hand, hold the middle of the sponge head in the other, and pull it out vigorously.

2. Prepare the sponge head.

If there is a spare sponge mop head at home, we can find the sponge mop head and tear off the plastic film on the outside with scissors. If we don't have a spare sponge mop at home, we need to buy it in store. Generally, mops are general-purpose, and you can buy general-purpose sponge mops.

If you are not sure, we can measure the size of the original sponge mop and purchase a mop head of the same size.

3. Install the sponge head.

When installing the sponge head, we can first rinse the tray at the bottom of the mop and wipe it clean. Then we take the sponge head, and there are two plastic sheets above the sponge head. Let's align the buckle on the plastic sheet at one end of the sponge head with the card slot of the mop pallet and insert it.

Next, we push the sponge forward and mount the plastic sheet at the other end of the sponge head on the mop holder. Finally, we flatten the sponge head.

How to change the sponge mop head.

Hello Zheng Defeat, I am happy to answer for you, call Cong Bi 1, disassemble the sponge head folding sponge mop The sponge head is stuck on the pallet. We can insert a slotted screwdriver into the gap between the mop and the sponge head, and use the screwdriver to push the sponge head out forcefully, and then we can remove the buckle of the sponge head from the card slot of the pallet and remove it. Or we put on gloves, hold the mop in one hand, hold the middle of the sponge head in the other, and pull it out vigorously.

2. If there is a spare sponge mop head at home, we can find out the sponge mop head and tear off the plastic film on the outside with scissors, and try to reduce all the plastic film on the sponge head without residue. If we don't have a spare sponge mop at home, we need to buy it in store. Generally, mops are general-purpose, and you can buy general-purpose sponge mops.

If you are not sure, we can measure the size of the original sponge mop and purchase a mop head of the same size. 3. Install the sponge headWhen installing the sponge head, we can first rinse the supporting plate at the bottom of the mop and wipe it clean. Then we take the sponge head, and there are two plastic sheets above the sponge head.

Let's align the buckle on the plastic sheet at one end of the sponge head with the card slot of the mop pallet and insert it. Next, we push the sponge forward and mount the plastic sheet at the other end of the sponge head on the mop holder. Finally, we flatten the sponge head.

I hope mine can help you, if you are satisfied with my service, please give a thumbs up, I wish you all the best!