What tools do you need to prepare for a home inspection What are the delivery standards for a rough

The tools that need to be prepared are small leather hammers, buckets, and rangefinders. Electrical plug, camera, tape measure. The standard of delivery is that all the pipes are packaged completely, without any damage, all the decoration is in line with the decoration project, and the pressure of various pipes is in line with the corresponding operation, and the decoration should be carried out in accordance with the decoration plan, and the water storage experiment should be carried out.

5m box ruler, tongs tool: with large socket with two and three plugs, mirror, flashlight, plastic bag, lighter. Whether the doors and windows are loose, and whether there is any water leakage in each room.

You need to prepare a tape measure, you need to prepare, a multimeter, as well as a voltage tester, feeler gauge, etc.; All the exterior decoration has been completed, the prefabricated floor slabs or unglued ceilings used in each room have been decorated, and the acceptance work of water pressure test has been completed, and the waterproof layer has been completed.

Home inspection is the overall inspection of the house, the professional and technical requirements are relatively high, and at the same time to prepare a lot of house inspection tools, ordinary owners to inspect the house is just a glance, take a look, for the details can not be controlled in place, and the use of house inspection tools can greatly improve the effect of the house inspection, so what tools are needed for the house inspection? Let's take a look, 1. Clamp tool: with a large socket with two-ended and three-ended plugs; **, TV, network monitoring equipment; Multimeter; Multi-use screwdrivers; A pair of No. 5 batteries, a voltage tester, a Fubi hammer, etc.

2. The multi-functional internal and external Li Tingxin right-angle detection ruler is mainly used to detect the deviation of the inside and outside right-angle of the object, as well as the verticality and horizontality of the ordinary plane. When using, push down the angle pointer box, when the pointer is in the zero position, the right angle is 90 degrees, and its deviation value is read directly, 1 mm per grid.

3. The purpose of the flashlight is to investigate the main structure of the house to see whether the wall is straight and whether there are protruding or concave parts. Hold a flashlight against the bottom of the wall and shine it upwards, and the shadowed part is the problematic area. At the same time, you can also use a flashlight in the flue and vent to check whether there is construction waste.

4. The vertical detection ruler is used for verticality, levelness and flatness detection, and is the most frequently used detection tool in home improvement supervision. Detect whether the wall and tile are flat and vertical. Detect whether the floor keel is horizontal and flat.

5. Vernier calipers are used to measure the length, inner and outer diameter and depth of the wheel room tool. Before use, wipe the measuring claw clean so that it is close together, check whether the zero tick mark of the vernier and the main ruler are aligned, if not, remember the zero error. When measuring, hold the ruler with the right hand, move the vernier with the thumb, and hold the object with the outer diameter (or inner diameter) to be measured with the left hand, so that the object to be measured is located between the outer measuring claws, and when it is closely attached to the measuring claw, it can be read.

The reading result is: l = integer part + decimal part - zero error.

6. There are three indicators on the test socket, from left to right, they represent the zero line, the bottom line, and the live wire, when the two indicators on the right are on at the same time, it means that the circuit is normal, and when the three lights are all out, it means that there is no phase wire in the circuit; Only the middle light is on, indicating a lack of ground wire; Only the light on the right indicates that the zero line is missing.

7. The water pressure gauge is used to detect water pressure, and it can also be used to measure the pressure of gas or liquid media that does not corrode copper alloy when the ambient temperature is between minus 40 degrees and 70 degrees.

8. Hose: Generally, during the house inspection, the water and electricity have been turned on. Owners can turn on each faucet to see if there is any water flowing out, and then pour some water into each drain outlet in a container to visually determine whether the drain pipe is smooth.

The inspection standards that should be paid attention to in the collection of rough houses are: it must meet the specified quality standards of housing construction projects and have a signed project warranty; Must have a housing quality certificate issued by the quality inspection station; Gas, water, electric heating, sewage, roads, 6 meters in front of the building, 3 meters behind the building, the site is leveled; It must be fully equipped and complete in accordance with the requirements of drawings and documents.

[Legal basis].Article 16 of the Regulations on the Quality Management of Construction Projects.

After receiving the completion report of the construction project, the construction unit shall organize the design, construction, engineering supervision and other relevant units to carry out the completion acceptance.

The following conditions shall be met for the completion and acceptance of construction projects:

1) Complete the construction project design and the contents agreed in the contract;

2) Have complete technical files and construction management materials;

3) There is an approach test report of the main building materials, building accessories and equipment used in the project;

4) There are survey, design, construction, engineering supervision and other units signed by the quality of the documents;

5) There is a project warranty signed by the construction unit.

If the construction project experience is qualified, it can be delivered.

How to inspect the rough house.

Specific to the closing of the house, buyers should pay attention to what problems to inspect, this article summarizes some of the problems that are prone to problems, buyers can do a comprehensive acceptance of the house according to the following content, or can ask professionals to accompany the house, in order to test out the problems that are not easy for us ordinary people to find.

1. Check the quality of the house in detail, including whether there is cracking in doors, windows, balconies and other parts.

2. Check the flatness of the wall, whether there is water seepage, and whether there are cracks. In particular, check whether there are water traces on some walls, especially the kitchen sanitary roof, exterior wall and other places, and if so, be sure to find out the cause as soon as possible. and let the developer carry out the repairs.

3. Carefully check whether there is any cracking of empty shells on the ground. If there is an empty drum, you must instruct the accompanying property personnel to repair it as soon as possible, otherwise it will be easy to penetrate the floor slab during the decoration.

4. Check the smooth flow of water, electricity and coal and whether it can be used normally.

5. Open all faucets to check for leaks, and make the water flow as loud and urgent as possible in order to check the water pressure and test the drainage speed.

6. Use a voltage tester to check whether the strong and weak currents are unblocked, and close the opening to check whether each branch line is fully controlled.

7. The acceptance of the drain includes basin drainage, bathtub drainage, toilet drainage, kitchen and sanitation and balcony floor drain.

8. Make an appointment with the owners upstairs and downstairs to check whether there is water leakage and seepage on the upstairs floor, their own ceiling, their own ground and downstairs ceiling, and record the record of the water meter.

After checking these work, if there is no problem, you can pay for check-in, if there is a problem, you need to determine the solution and solution date with the developer and property personnel, and then confirm the receipt of the house after agreeing that there is no problem, and the big problem can directly refuse to accept the house.

The rough house inspection mainly accepts the following items:

1. Building structure:

1.The quality of the building, such as foundations, walls, stairs, beams, columns, halls, floors, stairwells, etc.

2.The form of the building, such as beams, columns, walls, stairs, etc., dimensions, deviations, seismic resistance, etc.

3.The integrity of the building, such as wall bridges, wall perforations, foundation drainage and drainage pipes, etc.

4.The roof of the building, such as roof waterproofing measures, roof covering materials, etc.

2. Interior decoration of the building:

1.The location of water supply and drainage pipelines, the quality of installation, the connection watertightness, etc.

2.The decoration quality of the internal wall and floor, such as the flatness of the wall, the thickness of the mortar on the side of the key, the moisture-proof measures, etc.

3.The location, size, lock and sealing of indoor doors and windows, etc.

4.The location of indoor electrical installation, installation quality, safety protection measures, etc.

3. Decoration:

1.Wallpaper, carpets, tiles and other decoration quality.

2.Installation location and quality of lamps, switches, sockets, etc.

3.Ceiling, waist protection, partition and other decoration quality.