If I haven t used a hand drill to drill the tile wall, will it damage the tile? Any tips

Hand electric drill to drill tile walls, to use a tile drill bit, generally will not make the tile crack, but do not use too much force, the speed can not be too fast.

If you have tiled balconies, bathrooms and kitchens, it will be a hassle if you want to drill holes in them in the future. Because the tiles are relatively brittle, they will be broken if you are not careful. So how do you do that?

1. The first thing to do is to take a picture of the location of the hydropower with a camera to prevent drilling into the wires and water pipes. Then mark the area that needs to be drilled with a pencil and then apply some tape.

2. Remember not to use iron nails, to use sample punch or steel nails, first use a hammer and sample punch to make a small hole in the place just marked, so as to avoid the bricks will slip after touching the tiles. And the adhesive tape we just applied is to prevent accidental drilling.

3. Use the impact drill equipped with an impact hammer to vertically align the previously drilled holes, do not use too much force at the beginning, and then you can hit a little deeper after penetrating the tile.

4. After the hole is laid, the expansion pipe can be installed, and then the shelves to be installed are fixed.

Although the above is a more commonly used drilling method, but if the tile is more fragile, it is still easy to be cracked, here are three tips for you to offer:

1) When drilling, it will be better to choose the junction of the tiles, so that the tiles are not easy to crack, and it is best to be the junction of two tiles.

2) The middle part of some tiles is hollow, so remember not to be in the hollow place, which is easy to crack.

3) Because the water absorption of wall tiles is relatively high, you can continue to pour water on the wall tiles when drilling, and the tiles are less likely to crack.

In addition to the above methods, there is also a method introduced by netizens is to drill holes in the wooden board with a glass drill bit, so that the tiles can be fixed.

Hand drills are available to drill wall tiles.

A hand drill is a drilling tool powered by AC power or DC batteries, and is a kind of hand-held power tool. A hand drill can drill into walls, but if it is not a percussion drill, the drilling effect is not ideal. However, it can also be improvised, especially the brick wall is not too strong, and it is easy to drill holes.

In fact, the drill wall mainly depends on the drill bit, and the requirements for the drilling rig are not strict, just drill the hole and put a small plug or something. However, the drill bit generally needs an alloy head, otherwise it is easy to burn. The size of the hand drill is small, it cannot be used on the large drill bit, and the weight is also light, but it is easy to deviate and cause the drill bit to break.

Hammer drill (electric hammer) is different, it is the use of the bottom motor to drive two sets of gear structure, one to achieve it drilling, and the other set to drive the piston, just like the engine hydraulic stroke, producing a strong impact force, accompanied by the effect of drilling. Strength can split stones into gold.

The electric pickaxe is to let the motor drive the shaking stone to run in the form of bouncing, so that the pickaxe has the effect of chiseling the ground. The hydraulic pump pickaxe uses the gas pressure transmitted by the air compressor to drive the pump hammer in the electric pickaxe to bounce back and forth, so as to produce the effect of the pickaxe hitting the ground, but the electric pickaxe only chisels, and its pickaxe head does not rotate.

All in all, the electric drill can only drill, and the impact drill can also have a slight hammering effect. Hammer drills can drill and higher hammers, while electric picks can only do hammering and cannot drill.

OK. High-end drill chucks are mainly used in professional power tools, bench drills and other occasions with high requirements, and the demand for high-performance self-locking drill chucks and heavy-duty wrench drill chucks is increasing. The high-performance self-locking drill chuck has the characteristics of high precision, high technology content, high added value and high efficiency, and is mainly matched with the impact drill above 850W and the DC impact drill with 24V in professional power tools.

Due to the improvement of the quality performance of power tools, it is required to be able to reliably carry out drilling operations in vibration and impact occasions, so it is required that the supporting drill chuck has a locking function to ensure that the drill bit and other tools clamped by the electric drill in use are not loose. The global demand for self-locking drill chucks is expected to be about 19 million by 2010.

First, the electric drill product is a compulsory certification product stipulated by the CNCA, so when purchasing, you should first check whether the tool has the 3C mark, the method of checking is generally, whether there is a 3C mark on the outer packaging of the tool or the nameplate of the tool, if there is still doubt about this (because the manufacturer of the electric drill has not passed the annual supervision and review, the CNCA has suspended or revoked its certificate), you can go to the CNCA to check whether the 3C certificate of the tool is currently valid.

Second, when buying electric drills, you should choose large companies with good reputation and more influence, because these large companies have strong technical force, strict quality control, and standardized after-sales service. Users with strong purchasing power can also buy some tools from international brands.

OK. The main specifications of the electric drill are mm, etc., and the number refers to the maximum diameter of the drill bit drilled in steel with a tensile strength of 390n mm2. The maximum drilling diameter of non-ferrous metals, plastics and other materials can be 30 50% larger than the original specifications.

The working principle of the electric drill is that the motor rotor of the electromagnetic rotary or electromagnetic reciprocating small-capacity motor does the magnetic field cutting and does the work, and drives the operating device through the transmission mechanism to drive the gear to increase the power of the drill bit, so that the drill bit scrapes the surface of the object and better penetrates the object.

Hand drills are only suitable for more use scenarios and more efficient when they are powerful. This SATA Shida 320W 10mm AC hand drill, 320W strong power, more powerful than similar lithium drills, multi-tuyere ventilation design, effective heat dissipation, prevent the click temperature from being too high. The product has passed 3C certification, and the safe use is guaranteed.

The following cross-sectional illustration shows the fine internal structure of the drill.

The ergonomically designed spherical non-slip handle, the bottom sticks out forward, which is very firm to grasp, and it is not easy to accidentally slip off during use. The shell of the electric drill is also designed with matte, so it is not easy to slip when in use.

Of course, you can drill small holes directly with a small drill bit, but the strength is lighter and you can take it slowly. Large holes are not good, because the drill bit is large, it is easy to damage the tile surface, you have to use a glass drill bit to drill through the tile first, and then install the drill bit back and then drill.

Drilling tools that use electricity as power. It is a conventional product in power tools, and it is also the most demanded power tool products. The annual production and sales volume accounts for 35% of China's power tools.

The main specifications of the electric drill are mm, etc., and the number refers to the maximum diameter of the drill bit drilled in steel with a tensile strength of 390n mm2. The maximum drilling diameter of non-ferrous metals, plastics and other materials can be 30 50% larger than the original specifications.

There are special glass drill bit cut-outs. There are 6mm, 8 passwords, 10 passwords, 12 passwords, and 18mm can be installed on the hand drill.

The small electric drill is very useful, and there is a suitable drill bit that can easily drill through the tiles!

It is used when installing small parts in the bathroom.

It is safer than percussion drills, and can be used to drill 6mm holes with alloy bits and lower expansion plugs.

It's easy to break the tiles, but there are successful examples, which may have something to do with the sharpness of the drill.

It's still okay to change the drill bit, if it's not a glass drill bit, it's recommended not to drill.

Drilling with an electric drill is optional. You can first adjust the electric drill to low speed, then drill on the surface of the tile, and then accelerate after entering, so that the tile is not easy to break. Here's how:

1. Before starting construction, check the water and electricity road map of the previous home decoration to ensure that there are no water and electricity lines on this wall.

2. Draw the size and diameter on the wall with a pen, and then find a tile left over from the previous decoration. Draw the same diameter and drill a hole in the discarded tile first.

3. Spray some water on the wall, otherwise the temperature will rise when the eye is drilled for a while, and the tiles will be easy to crack. After spraying water, aim the hole on the waste tile to the hole on the wall, use an electric drill to align it vertically at that point, slowly force through the tile, and after opening a small opening, you can remove the waste tile, and then force it on the wall to reach the appropriate depth.

4. After the hole is laid, stuff the expansion tube of about the same size into it, and then use a screwdriver to screw the basket up, and then tighten it.

If you want to punch holes, you only need to use an ordinary electric drill, and you only need to change an electric drill bit and use our open electric drill. The drill bit will do, and it can be punched on the assassin, and you can make as many holes as you want.

The safest way is to use a hand drill to clamp a glass drill bit to open a hole, so that the tiles will not break!

Yes, but not as well.

1. It is better to use a percussion drill or electric hammer to drill the wall, and the hand electric drill can be used to hit the red brick wall, but the drilling effect is not ideal, but it can not be used to drill the cement wall or the concrete envy of the earth wall, and it is easy to scrap the drill bit, not to mention that it is thankless.

2. You can choose the combination of hand drill and electric hammer to drill the red brick wall, so that the work efficiency is relatively high and easier.

3. The drill wall mainly depends on the drill bit, and the drilling rig requirements are not strict, just drill the hole and put a small plug or something. The drill bit should be alloy head, otherwise it will be easy to burn if it is cautious. You can also choose to buy a percussion drill set, which has the function of a hand electric drill, but Brother Xiaoshan is similar to the electric hammer with a weaker function.

Hit with a tile drill will definitely not break. I've been using it for decades.

The tile surface is perforated, and the position is selected correctly. Before punching the tile, we should confirm whether the tile at the hole is hollow, and also confirm whether there is a water line pipe in the wall. If the hole diameter of the hole we punch on the surface of the tile is very small, choose a special drill bit for the tile to drill the hole.

The aperture is relatively large, and it is recommended to choose a special hole opener for ceramic tiles. Be sure to prepare a tool for flushing before punching.

Before punching, check whether there is a hollow drum in the punching part, and pay attention to the straightness of the direction of the drill bit and the uniformity of the strength when punching.

First of all, do not hit the edge of the tile easily crumbling. Secondly, first chisel a small hole to avoid slipping, and use the electric drill of the speed switch to drill the hole step by step. Finally, after making the holes, select the appropriate expansion tube to bury and fix the required installation objects with screws.

When using a glass drill bit to punch holes in the tiles, first make a pit in the direction of inclination; Otherwise, the tile is too smooth and difficult to locate; Or it's not all tiled, just make a small hole with nails; If you want to be precise, it is best to use a plate that already has holes (of the right size).