When drilling holes in tiles with an electric hammer, how can I avoid tile breakage?

Confirm the location of the hole, and then make a visible mark with colored pencils, including the center of the hole and the area to be punched. Use a hammer and sample to punch holes, make a standard small hole in the mark, and take a rag to remove the enamel from the surface of the tile. Select the diameter you need, mount the drill bit on the hammer, and start drilling by aligning it at the point you just saw.

Don't push too hard. If you use too much force, the tile can easily crack and fail.

First of all, the selection of tools is very important, without a good tool, even if there is a good experience, it is useless 1, but also the speed switch, punching holes in the tile, need a cyclic gradual process, not in a hurry, and the speed switch of the electric hammer can adjust the speed of drilling, when punching on the surface of the tile, you can press the switch, slowly drilling, when the tile drilling, you can increase the pressure degree, accelerate the injection, so as to ensure that the tile is not broken 2, ordinary electric drill, if there is no electric hammer of the speed switch at home, If you only have an ordinary electric hammer, if you want to avoid the situation of broken tiles, you can first use an electric hammer drill bit to chisel a small hole, so as to avoid the use of electric drills when the drill bit slips on the tile surface, causing the tiles to break, and then use the electric drill to drill the tiles through the impact drill bit.

1. First make a cross mark on the spot you want to punch, and then gently tap the porcelain piece on this mark point with a cement steel nail. There are two important points to note at this time. The first point is that the steel nail tip should not be too perpendicular to the surface of the tile.

The correct way is to tilt the steel nail diagonally towards the tile so that there is an angle between the two, which is conducive to breaking the surface of the porcelain tile.

2. The force of striking the steel nail should not be too large. If the porcelain piece is not broken and struck hard, it is easy to cause the porcelain to collapse on the surface of the tile, and it will not be a point that will be broken at that time, but will show an irregular flake.

You can pad something under the tile, and then adjust the switch of the electric hammer, adjust its speed, enter slowly, and do not increase the pressure, otherwise it will cause the tile to break.

Do not use iron nails, use a pencil to mark the area to be drilled, and then apply tape, and when punching the hole, it should be vertical.

To solve the problem of fragile holes on the tiles, the materials that need to be prepared include: adhesive tape, pens, electric hammers, and water.

First, first use adhesive tape in the shape of the word "ten" and paste it on the tile.

Second, use a pen to make eye markings.

3. Then use an electric hammer to start drilling, drill a little first, and don't penetrate the tile directly at once.

Fourth, then tear off the adhesive tape, continue to punch the hole while sprinkling water, to cool down the tile, so as not to break the temperature too high.

Fifth, in this way, use an electric hammer to punch holes in the tile, and the tile is not fragile.

First, mark the position of the tile to be punched with a marker pen (the best part to choose a solid part), and paste the sealing tape. Use a hammer and a sample punch (if you don't have it, you can use a large steel nail, remember that you must have a steel nail, also called a cement nail, and not an iron nail) punch out about two small points in diameter at the mark, so that the enamel on the surface of the tile is removed.

Second, select the required diameter impact drill bit to install the punch, vertically for the punch point, give the appropriate amount of pressure to start the punch, the feed should not be too large, slow force can be able to penetrate the tile smoothly. After penetrating the tile, it can be forcefully fed to the desired depth.

3. After drilling the hole, select the appropriate expansion pipe to bury and fix the required installation objects with screws.

To see what kind of tile, if it is a homogeneous full tile, it is necessary to use a hand drill with a glass hole opener to drill holes, and must not use an electric hammer.

If it is an ordinary glazed brick, it is best to use an electric hammer with a special drill bit, and it is best to use cement nails to nail a shallow pit at the position where the hole needs to be drilled before using the electric hammer, so as to facilitate positioning, and the electric hammer is best to use low grade.

First, use a nail to eject a positioning point on the tile, the drill bit of the electric hammer should not be installed in place, it can rotate normally but will not be hammered until the tile is penetrated, and then the drill bit is installed in place to impact the wall.

It is not to be hammered with electricity, but to drill by hand, and if it is necessary to drill into the wall, it is necessary to drill the hole and then use the electric hammer.

First, it depends on whether your bricks are hollow when paved, and second, it depends on whether your bricks are made of full tiles. If one of the two points of appeal is answered in the affirmative, then the punch is bound to be broken. It is recommended to use a glass drill bit with an ordinary electric drill to punch holes is the safest.

The position of the hole to be punched is pre-calibrated to ensure the level. (Note that there should be no water and electricity lines in the corresponding position in the wall) when punching holes in the tiles with a glass drill bit, first make a pit in the direction of inclination; Otherwise, the tile is too smooth and difficult to locate; Or it's not all tiled, just make a small hole with nails; If you want to be precise, it is best to use a plate that already has holes (of the right size).

Set to make a shallow mark can remove the positioning of the orifice plate, and. Prepare a water bottle in advance, drill a hole in the cap, and fill the bottle with water. Then, when punching, the water should be moistened to the contact part of the drill bit and the tile at the same time; Especially with all tiles, there must be water.

There is no need to change the percussion drill bit. Punch through the tile part and continue to punch the screw depth. Pay attention to make a hole, remove the glass drill bit, and dredge the hollow part of the blocked drill bit.

In the process of drilling, you start by drilling slowly, and don't push too hard.

But what I use at home is cheap tiles, to give you a tip: I use an impact hammer, when drilling, you can't drill with iron nails on the porcelain tile lightly hit a dozen to break the glaze, to prevent the drill bit from slipping on the porcelain tile. Won't crack.

No, first you make sure to turn off the impact is no problem, if you don't grasp it well, you can take a steel nail and snail it on the wall at the position where you expect to hit the hole, so that the electric hammer will not slide out of the predetermined position. For newbies...

If the tiles are better, they won't. And when making holes, the point should be fixed as much as possible, hold the hammer steadily, and don't let the hammer slide everywhere. The installation of things in my bathroom is, and the few holes are very good.

If there is a crack in the tile, there is no way to repair it.

It is recommended that you remove the cracked tiles and put new tiles on them, which is more beautiful. There is the original cement on the wall, and the new tiles can be pasted with super glue, and the adhesion of super glue is high, and the tiles can be fixed on the cement wall.

In addition, use an impact drill to punch holes in the tile, you must pay attention to the top angle of the drill bit should not be too sharp, keep it at about 120 degrees, the speed of the impact drill should not be too fast, and the operation should not be too hard.

For the decoration of a new house, it is indispensable to punch holes in the tiles and install various pendants. How do you make an eye on the tile? Electric hammer or electric drill for tile drilling?

To be honest, even if it is a master, it is inevitable that he will accidentally break the porcelain tile by punching holes in the tile, but the master has a trick in how to repair the tile hole. Next, I will mainly introduce you to tile eye-punching matters.

First, how to punch the tile.

Be sure to check whether the tile has a hollow drum, and you must choose a place without a hollow drum for punching, otherwise the tile will crack. Step 2: Paste the sealing glue at the perforated position for the purpose of positioning, and the other can also prevent the tile from cracking.

Use an electric drill to open the tile first to the flat drill mode, and clamp the special opening. To keep cooling the drill bit with water, at the beginning due to the smoothness of the tile drill is not easy to position, you can open a shallow crescent groove to do positioning, after penetrating the tile, and then use this drill bit is obviously inefficient, then use an electric hammer or impact drill.

Take a cement nail, open a small hole in the place where you want to punch, the purpose is to prevent the drill bit from slipping when punching, you must pay attention to the electric hammer is a flat drill, just start punching, you should easily press the switch first, and slowly punch the hole.

Second, how to repair the tile hole.

If there are cracks in the tiles, how should Lao Zheng repair them? Regarding how to repair the tile hole, you don't have to panic. If the void is not too large and does not affect normal life, it can be filled with glass glue, and toothpaste can also be used instead without glass glue, the purpose of this is to prevent the gap from becoming black.

If the tile is accidentally cracked, you can use tile repair agent to repair it, and you can easily open it to repair the cracks and small holes as before.

Third, ceramic tile drilling with electric hammer or electric drill.

Electric hammer or electric drill for tile drilling? The master told you that you need it, in addition, with a marker, sealing glue (glass glue, toothpaste). After the electric drill breaks through the cement wall, change the original flat drilling mode to the hammer drilling mode, and press the switch button at the same time to quickly punch the hole, which can be completed.

When punching holes, if the whole wall is covered with tiles, remember to add water to cool the holes.

Tile drilling is a careful job, you can't be impatient, fortunately now many things have become non-punching, and there is no need to be so troublesome to punch.

The above is for you to share how to drill the tile, how to repair the tile drilling, the relevant knowledge of the tile punch or the electric drill, I hope it will help you. If you want to know more about how to drill ceramic tiles, how to repair ceramic tile drilling, and information about using a hammer or an electric drill for tile drilling, please continue to pay attention.

First of all, the surface of the tile is simply treated, and the part of the drilling position on the tile surface is removed first, so that the drill bit will not directly touch the surface of the tile and prevent cracking. The other is to drill with a special tile drilling tool, and then drill with a percussion drill to drill deep.

If you want to prevent the tile from breaking, the best way is to pour a little water on the tile, and then use the electric hammer hard, and then drill the hole, so that you can, the effect is very obvious and will not break.

Tape the tile in a cross-shaped shape, and then mark it with a pen and punch it so that it doesn't break.