Will the tile crack when punched, how to punch the tile will not crack

Drill holes with ceramic tile bits that will not crack.

Due to the needs of decoration construction, it is necessary to punch holes on the wall of tiled tiles, and there are many details to pay attention to at this time, so as to avoid cracking of tiles as much as possible and affect subsequent use. So how to punch tiles without cracking, and what needs to be considered for tile punching, do you understand? Now let's take a look.

First, how to punch the tile will not crack.

Before punching the tile, it is necessary to put the percussion drill at the same level as the tile punching position, and hold the percussion drill tightly to prevent it from getting off when punching, so as to effectively prevent the tile from cracking. In addition, you should not use too much force to punch holes in the tiles, but wait for the tiles to be penetrated, and then increase the intensity to make deep punches.

Second, what need to be considered for tile punching.

1. Before punching holes for wall tiles, it is necessary to know that the percussion drill will generate a lot of heat in the process of high-speed operation, in order to prevent unnecessary troubles, when using the percussion drill, it is necessary to add water to the percussion position, so that it can be better cooled down, and to a certain extent, it can also prevent the cracking of the tiles.

2. If the cracking of the tile is accidentally caused in the process of punching, then it can be repaired appropriately according to the actual situation. If the crack is not very large, you can use a toothpaste of the same color, apply it to the crack, and then use a soft-bristled toothbrush to paint it, and after the crack is not visible, you can do it.

3. The size of the hole punched in the tile depends on the size of the bolt to ensure that the bolt can be better embedded in the hole of the tile. In addition, before punching, you can also paste the sealing glue on the tile, which can prevent the slippage of the impact drill during the punching process, and reduce the cracking of the tile to a greater extent.

About how to punch tiles without cracking, and what needs to be considered for tile punching and royal belt holes, I will introduce it here, do you understand? There are a lot of details that need to be paid attention to when tile punching, if it is not dealt with well, it is very likely that the tile will crack, which will affect the overall aesthetic effect.

How to punch the tile so that it will not crack the pro! Hello, I am glad to answer for you<> pro-tile punching will not crack the method is as follows: the first step: tap to check whether the tile is hollow Select a tile with a more solid paving Try to choose to punch a hole in the center of a tile Mark the position with a marker.

Step 2: How to determine that there is no water pipe and electricity behind the detection of the perforation position? The most convenient way is to look at the layout of the water and electricity, and the owners who can't find it are safest with the help of a wall detector.

Use it to scan the walls, if there are wires in the walls, an alarm will sound, and then avoid the location to punch holes. To save money and trouble, you can also take a small look at the wall and then go deeper. However, you have to think clearly, if the position of the wire is detected, this hole will inevitably affect the visual appearance.

Step 3: Once you have determined that the position is OK, seal the perforated points with a wide transparent tape in a criss-cross manner, which is very important! Very important!

Reduce the chance of tiles bursting! Step 4: Lock the position with a nail and first drill a 2 3mm small hole in the borehole with a cement nail.

This action is mainly due to the fact that the surface of the tile is too smooth, and the drill bit is easy to slip when punching, which is dangerous and may also destroy the tile! Step 5: Then, enter the drilling link and first adjust the electric drill to the flat drill mode, slowly penetrate the tiles, go to the wall part after entering, and then adjust to the hammer drill mode, so that the tiles are not easy to break.

Once the hole is ready, then stuff the screw into the hole, tighten it, and you're done! Here are a few precautions, you should remember: when punching, it is best to have a partner next to you.

Prepare a mineral water bottle with water in advance, punch a few holes with a needle on the lid (it is easier to use a lighter to heat the needle and pierce the hole), and then when you punch the hole, you can get the water to the contact between the drill bit and the tile. Because when drilling, the temperature of the drilling position will rise sharply, causing the tile to burst. Do not punch holes in the bulging areas of the tiles, as there is a gap between the tiles and the wall, which is more likely to burst.

When two holes need to be drilled and the distance is very close, it is best to plug the plastic nut tightly after the first hole is made, and then make the second hole, which can reduce the possibility of tile cracking. Hope mine can help you <>

Do you have any other questions?

<> try not to use an electric hammer to punch the tile directly, you can use a special drill bit for tile drilling, you can also use rhinestone to drill holes, or you can also use the normal electric drill mode of a percussion drill to grind the outer porcelain surface of the tile, and then use a percussion drill to drill the hole. When drilling holes, it is best to use a pre-prepared mineral water bottle to pour them on while drilling the hole to avoid the problem of tile chipping caused by overheating.