What are the disadvantages of sticking tiles first and then punching holes?

Home bathroom, kitchen, one is the air is humid, the other is smoke. In order to protect the walls and clean the interior, the wall tiles must be finished. But in any case, after the bricks, some shelves of some life need to be hung on the wall so that they will be very neat.

However, the rack hangs on the wall. How to punch holes in the wall tiles to make sure that the tiles are free of cracks, but it is an insult for most people. In fact, as long as you master the correct stamping method, the tiles will not fall, and the tiles will be easy to punch.

Before punching holes, the waterline location must be determined to avoid hitting the water and line pipes. After deciding on a good location, you can use a pencil to draw it on the tile. Note: The punching method cannot have empty drums.

And it is easy to fry in an empty drum.

Once all the work is done, you need to use special triangles.

The drill bit punches holes in the tile. When punching, percussion drilling.

Flat and vertically perforated. To avoid taking holes, there must be a percussion drill before playing.

When it is best stamped, stamping water when spraying, avoiding drill bit and tile friction, thermal expansion and cold shrinkage. Second, don't use too much force in front of the drill bit, don't use too much force, and wait until you're wearing your back.

After the expansion of the thing is good, the rack can be hung up and then used with a screwdriver.

After the hole is good, the size of the expansion plug in the hole is located in the hole, the tile is improved, and the wall can also act as a protector.

Once the expansion plug is plugged, you can hang up the shelves and tighten the screws with a screwdriver to prevent them from falling off. If it is not fixed in the early stage, and the number of times it falls off in the later stage, the hole cannot be used. When punching, go to the perforated part to cool down the tile to prevent the temperature of the tile from changing sharply instantaneously during punching, resulting in cracking of the tile.

When punching, pay attention to the uniformity of the force of the percussion drill and the consistency of the direction.

After pasting the tile, if you punch the hole again, it may blow up the tiles that have been pasted, which will affect the beauty of the tiles. Second, even if the tiles are not damaged, they will be slightly loose and easy to fall. The third is that after the tile is pasted, it blocks the line on the wall, and the hole is easy to touch the line.

That will make the freshly pasted tiles fall down again, which will cause waste, and even if the tiles do not fall, there will be gaps due to vibration, and the tiles will not be well pasted.

When decorating, you should pay attention to the order of hard installation, and there are many disadvantages in sticking the tiles first and then punching holes. First of all, it will destroy the integrity and aesthetics of the tiles, and then affect the aesthetics of the entire area and destroy the aesthetics of the entire house. Secondly, the hardness of the tile is relatively large, and the post-punching undoubtedly increases the difficulty of punching and increases the labor cost.

You can choose to drill with an electric drill. DU can first adjust the electric drill to low speed, and then drill on the surface of the porcelain brick, and then accelerate after entering the DAO, so that the tile.

The version is not easy to shatter. Here's how:

1. Before starting construction, check the water and electricity road map of the previous home decoration to ensure that there are no water and electricity lines on this wall.

2. Draw the size and diameter on the wall with a pen, and then find a tile left over from the previous decoration. Draw the same diameter and drill a hole in the discarded tile first.

3. Spray some water on the wall, otherwise the temperature will rise when the eye is drilled for a while, and the tiles will be easy to crack. After spraying water, aim the hole on the waste tile to the hole on the wall, use an electric drill to align it vertically at that point, slowly force through the tile, and after opening a small opening, you can remove the waste tile, and then force it on the wall to reach the appropriate depth.

4. After the hole is laid, stuff the expansion tube of about the same size into it, and then use a screwdriver to screw the basket up, and then tighten it.

First, use glass drills to turn the tiles through, and then use an electric hammer to hit the holes, and there is no damage to the wall tiles.

First use the diamond drill bit of the hand drill drill to pilot the hole, and then use the impact drill to be foolproof.

1.Prepare the same type of porcelain source.

After the piece, the old cementing agent around the broken porcelain tiles on the wall should be cleaned first, and the damaged porcelain tiles should be removed.

2.If you want to cut it into curves or special shapes, you can first use a glass knife to carve out the wheel corridor, and then draw several cross blocks in this area.

3.Use flat-nosed pliers to carefully remove the carved wheel corridor piece by piece, and file the edges smoothly with a hand file.

4.Apply the cementing agent to the back of the new porcelain tile with a scraper, taking care to leave a blank space of about 12 mm around the edges.

5.Hold the edge of the tile in your hand and apply pressure gradually, paying attention to whether it is flush with the surrounding tiles.

6.Fill the edges of the tiles with cement, taking care not to leave gaps, and remove excess mud.

7.Remove any remaining cementing agent with a damp cloth and the perfect wall is revealed.

First of all, you need to figure out that there is no water pipe or electric line behind the location of the hole, and then mark the position that needs to be drilled, which can be marked with a marker, etc., to play an eye-catching role, and paste the sealing tape at the marked position, the first step is very important, and it must be done well.

Secondly, prepare Yang Chong and hammer, and punch out a small hole of about 2-3 mm in the position of the sealing tape, which can remove the porcelain enamel on the surface of the tile, otherwise the surface of the tile is too smooth and not easy to eye.

Then prepare the drill bit that matches the size of the hole, aim at the punch point, activate the impact hammer, and use just the right amount of force to slowly penetrate the tile until it has drilled deep enough.

Use a professional hole turning tool, or you can prepare 1 brick like the wall tile, so that the hole can be filled with that tile

Skids drill holes to reduce vibration.

1. The top of the tile can be punched.

2. As long as we prepare the relevant workers and tools, and then determine the location of the punch. Because not any place on the tile can be punched, we must be very familiar with the arrangement of the tile, in order to ensure that the hole is easy to star.

3. You need to mark it with a marker, and then prepare an electric drill to drill gently. If there are no problems, punch the hole quickly and accurately.

To punch holes on the tiles, first of all, you must determine the location of the water pipes and wires to avoid damaging the water pipes and wires.

When decorating, it is inevitable to punch holes, and punching holes in the tiles will not lead to cracking of the tiles: the location of the holes is calibrated in advance to ensure the level (pay attention to the corresponding hydropower project route in the wall). If the floor tiles are too smooth and not easy to accurately position, use steel nails to immediately make a pit or use a plate sleeve with holes to play.

Then, prepare an Aquarius and fill it with water, and let the water reach the point where the twist drill and the floor tile touch when you open the hole. Make a hole, lower the tile drill bit, and use a triangular drill bit or a percussion drill bit to block the hole and pass through the soil in the hole at a high speed, so that the surging sleeve will go deeper when knocked in, and it can also promote the installation of the object to bear more firmly.

Before opening the hole, it is necessary to clarify the wiring position of the water and electricity lines to prevent them from entering the water pipes and threading pipes. After determining the location, you can directly use a pencil to draw the location of the hole in the tile. And there can be no wall hollow in the open area, and it is very easy to burst the floor tiles in the hollow area of the wall.

After all the work is ready, use a special triangular drill bit to make a hole in the tile. When opening a hole, the impact drill Chunyou, open the hole vertically to prevent the hole from being deviated, and be sure to hold the impact drill tightly before hitting to prevent it from changing hands.

It is best to open a hole while sprinkling water to prevent the twist drill from rubbing with the floor tile to generate heat, and the heat expansion and contraction will burst. In addition, before the twist drill has not burst the floor tiles, you can't use particularly large force until you hit it hard. After the hole is laid, the same size of the plug is stuffed into the hole to improve the wear resistance of the floor tiles, and it can also have a protective effect on the wall.

If there is no fixed in the early stage, the number of times it falls down in the middle and late stages, this hole can not be used, in the process of opening the hole, pay attention to grasp the smoothness of the direction of the twist drill and the symmetry of the strength; In the process of opening the hole, two people can actually operate, one person is responsible for the opening, and the other person can sprinkle water on the opening position (you can take the mineral water bottle cap to punch the hole, and then fill the Aquarius with water, and sprinkle the backlog of water to the opening position).

Choose the right machine to solve the problem, make arrangements in advance, then you can ensure safety, the choice of tiles is also very important.

If you want to punch holes when decorating, you must ask a professional master to do it, which can reduce the chance of tile cracking.

When decorating, if you punch holes, it is likely to cause the tiles to crack, so try to avoid this, and if you want to punch holes, try to avoid places with tiles.