How long does it take to brush latex paint after scraping putty putty and latex paint are brushed tw

Generally, the putty can be brushed with latex paint in three to five days after scraping. But according to the local weather, you can't brush it until he's done anyway. The construction of plastering is generally one plaster, two putty, and two latex paints.

A more stringent painting will have a bottom and two sides. But generally speaking, the putty can be treated with latex paint on both sides.

Usually, the wall of the blank house needs to be scraped three times with putty. Gypsum powder needs to be added to the first putty to increase the hardness of the putty layer; For the next two coats of putty, you can directly use ordinary putty to scrape; If it is not a rough room, depending on the condition of the original putty layer, it is decided whether the putty layer needs to be removed. If the quality of the original putty layer is good, then you can brush the ordinary glue (such as 801, etc.) first, and then scrape the putty twice to level it, and then brush the wall paint after sanding.

The wall paint is generally brushed 2 or 3 times (determined by looking at the hiding power of the wall paint), and the primer must be brushed before the wall paint is painted.

Putty only needs to be brushed once, since there is interior wall putty, why do you need to brush exterior wall putty? Exterior wall putty is not environmentally friendly and is not suitable for indoor use. Now that you've brushed the exterior putty twice, it's time to brush the interior putty!

However, this formaldehyde and other pollution may be more, and you need to dry it for a while. Chenguang putty powder is water-based and environmentally friendly, with strong adhesion, to ensure the long-lasting decorative effect of the topcoat. The process of brushing latex paint is to brush putty leveling first, then primer, and finally latex paint.

Need. After scraping the putty, it can generally be brushed in about 3 to 7 daysLatex paint

Scrape putty. It is one of the methods of interior wall decoration, scraping putty on the wall to ensure that the wall is flat. Generally, scrape three times, and after drying, polish it with sandpaper.

This step is carried out before the latex paint is applied. Scraping putty refers to the most important step in the treatment of the base layer by filling or overall treatment to remove the uneven part of the surface of the base layer and keep the wall flat and smooth.

Precautions for brushing latex paint:

1. Try not to participate in water for dark paint, otherwise it is easy to have color difference; It is best to complete the painting at one time, otherwise it is easy to have color differences.

2. Do not paint in humid weather or winter, otherwise it will affect the overall construction quality, and the paint is not easy to dry.

3. Pay attention to indoor ventilation and heat dissipation, and the grinding of paint and paint should be carried out after it is completely dry.

4. When the brush is finished and waiting to dry, soak it in water, and see if there are bubbles in the brushing place, and if there are bubbles, they will burst immediately.

5. When the brush is dipped in paint, the part of the bristles immersed in the paint should not exceed half of the hair length, if the root of the bristles is stained with paint, the paint brush will be deformed, and the service life of the paint brush 4 will be shortened.

Now many owners generally have two ways to deal with this wall, one is directly pasted with wallpaper, one is directly painted, with good coverage of latex paint or can, excessive, if the decoration to the age, the conditions are still allowed, redesign and decorate the answer given by the person, this construction process is not correct. The decoration sequence process is reversed, the ideal decoration effect cannot be achieved, and it is easy to rework if it is not done well, so it is very important to decorate according to the process order.

<> use a special ruler to level the baseboard base, glass fiber mesh cloth for trunking, and gypsum board ceiling seam pasting; Plaster leveling with large area leveling, waiting for the set door and custom wardrobe to be installed. Is it to scrape putty on the wall, install the wardrobe, door, and baseboard and then paint latex paint? In this question, the order of the installation of the wardrobe, the installation of the door, the installation of the baseboard and the painting of latex paint is asked.

So below the home miscellaneous altarDyeing furniture, polluting decoration phenomenon. In addition, if you install furniture such as wardrobes and then paint latex paint, it is difficult to brush the corners and corners, especially when your latex paint is darker, and even the color will be uneven. Brush latex paint first, brush the wardrobe or brush more than one in order, hit the wooden floor keel, make a fixed wardrobe, batch putty, spray latex paint, connect lamps, wooden doors, lay wooden floors, and press the baseboard.

I have to admit that decoration is a troublesome matter, but no matter how troublesome it is, you have to be patient to get it, otherwise it will be a big trouble to rework in the end, or it may be uncomfortable to live after completion.

Our new house is built to be painted, but also to install the cabinet, wardrobe according to my previous construction experience, first brush latex paint, let the master adjust the color when leaving a part of the adjustment for later repair, because there will be some bumps before moving in at home, and so on the home furniture, household appliances these are all in, let the latex paint if the door is installed first, there is a benefit to the wall painting, that is, after the door sleeve is fixed, the wall leveling is more obvious, When painting, it can repair the uneven wall surface, so that the wall and door cover are more flat and beautiful; In particular, door sleeve lines are generally difficult.

Twice. First use a roller to dip water in the wall ceiling and roll it again, then use a shovel to shovel off the white ash, wait for the foundation to dry thoroughly before making putty and brushing latex paint.

It must be full of putty, and the original wall white ash should be shoveled off before scraping the putty, the specific method is: first use a roller to dip water in the wall ceiling to roll again, and then use a shovel to shovel off the white ash, and then make putty and brush latex paint after the foundation is dry.

If you want the wall to be flat and free of cracks, then batch putty as a whole (preferably on both sides). After repairing the wall, you will be dissatisfied, and you will have to start again.

Scrape the putty 2-3 times, brush the latex paint once for the primer, and twice for the topcoat. Scraping putty is one of the methods of interior wall decoration, scraping putty on the wall to ensure that the wall surface is flat. Scrape 2-3 times, dry and smooth with sandpaper.

1.Generally, wall putty is most suitable to blow 2 or 3 times. After the putty is completely dry, it is sanded with sandpaper and then painted with latex paint.

Latex paint should generally be brushed more than twice, and it should be brushed evenly. Usually latex paint has to be brushed and sanded again, and finally sanded again. The two main ingredients in putty powder are talcum powder and heavy calcium carbonate.

The purpose of talcum powder is to plug the holes in the wall and make the wall smooth. Ground calcium carbonate is used to enhance the strength of putty powder, prolong the life of putty powder, and make it less prone to bumps. Both of these substances can be understood as powders made from stones, and talcum powder is made from talc.

Heavy calcium carbonate is made by grinding marble, limestone, and other stones. Both of these ingredients are non-toxic and harmless, but at the same time, both of them are non-sticky and cannot be attached to the wall. The key to scraping putty on the wall is leveling.

2.The so-called scraping putty a few times is actually to make up for the unscraped place in front. After the putty is scraped, it is thoroughly dried and sanded.

Sanding is to make the wall surface smooth and smooth. You can check whether it has been reached. Method: Use a 200-watt white fabric lamp to observe whether the wall is smooth.

Inevitably, in order to meet the construction period, some decoration teams start to scrape before the next layer is completely dry, and the moisture in the putty cannot be completely volatilized, so it is easy to crack and hollow. Generally, the first layer of putty can be scraped after it has slowly dried in the shade, while the third and second layers can only be carried out after they are completely dry every 3 days or so.

3.Before applying latex paint. After scraping the putty, look at it with a searchlight at night and pay attention at night!

Not in broad daylight! Close to the wall, you can clearly see the sanding, and then see if there is a hollow drum. Once you find that it is not done, quickly find a master to repair it, otherwise it will be difficult to rework the latex paint!

To protect the finished product, because when we paint latex paint, it is inevitable that there will be residual latex paint dripping, so we must first protect the finished product that has been decorated with something, generally using old newspapers or plastic wrap and the like. Do finished product protection, because when we paint latex paint, it is inevitable that there will be residual latex paint dripping.

4.Before painting latex paint, be sure to protect the finished product that has been decorated with something, usually old newspaper or plastic wrap or the like. That is to say, most of the latex paints on the market are not allowed to add water.

Rather, it is based on the requirements of the latex paint product itself. Some latex paints have their own thinners, and some latex paints can be used directly in open barrels. Therefore, when we mix latex paint, don't blindly add water.

Finally, I would like to remind you that the blending of latex paint must be in accordance with the product requirements. Once the grading is done, try brushing it and comparing it with our color chart until we get the latex paint color we need.