Many people say that tile adhesive is good, why do masons prefer to use cement to lay tiles?

1. Is tile adhesive really better than cement mortar? Let's first talk about the use of tile adhesive: add water to the powder of tile adhesive in proportion, stir it, evenly apply it to the brushed wall, and then paste the tile directly on it, and force it evenly.

Tile adhesive does not need to soak bricks, do not wet the wall, do not need to mix mortar, simple operation, easy to use, reduce the difference in paste effect caused by the ratio error, so the adhesion and construction efficiency are much higher than cement mortar.

Tile adhesive is resistant to high temperature, good flexibility, waterproof, impermeable, crack-resistant, anti-aging, especially suitable for humid environments, such as toilets. Tile adhesive is also especially suitable for full tiles with low water permeability, vitrified tiles, or tiles with relatively large specifications, and is suitable for wall tiles.

2. Why do bricklayers still like to use cement mortar? There are three main reasons.

1. Habit problems. Cement mortar is a traditional practice, and if you find the right master, it can be described as inexpensive and has been generally accepted by everyone for many years. At the same time, whether it is users who do not know about decoration or masters who are engaged in bricklayers, the acceptance of new things is still relatively slow.

2. ** factors. At first glance, the price of tile adhesive is relatively high, and many users and bricklayers will still default to cement mortar.

In fact, the overall cost of these two materials is about the same. Why? Cement mortar is only cheaper than the material cost.

Although the tile adhesive is expensive, it uses less material per square meter, and the construction efficiency is high, which saves the construction time, that is to say, the cost of the worker is saved. In addition, the tile adhesive has a good effect and is firmly pasted, and the tile adhesive still wins in general.

3. Leveling is required. As we all know, uneven walls and floors in our rough houses are the norm. The tile adhesive has high requirements for flatness, so in many practical situations, users and bricklayers are unwilling to spend more money to level the wall and ground.

If it is not leveled, the amount of tile adhesive will increase, and the cost will increase. At this time, it is more advantageous to use cement paving.

Because cement is paved with tiles, the viscosity of cement is stronger, and the viscosity of tile adhesive will be reduced after a long time.

Before paving with tile adhesive, the foundation should be smoothed with mortar, so that the tile adhesive can be tiled, and the cement sand paving saves the cost of smoothing and the high cost of tile adhesive.

With tile adhesive, do you still have to shovel and hang the wall?

If you want the tiles at home to be stable and durable, not hollow and not cracking, on the one hand, it depends on the quality of the tiles, and on the other hand, it also depends on the way of paving. In particular, the adhesive material chosen for paving is also important. When laying tiles, some workers will suggest that the owner choose to use tile glue to pave the tiles of the whole house, which is claimed to have high adhesion and is better than cement mortar.

But is that really the case? Tile adhesive, commonly known as tile adhesive, is actually the same as cement mortar, but a little more glue is added after mixing. Therefore, it is more viscous, the texture is light and thin, and the tiles are not easy to fall off after being pasted on the wall.

Because of this, it is a new type of adhesive material that can replace cement mortar. Although it has more advantages than cement mortar, it does not mean that the whole house should use tile adhesive!

The main advantages of tile adhesive are strong tiling ability, waterproof and moisture-proof, and not easy to age. It is mostly used for exterior wall decoration, the construction is simple, and there is no need to soak tiles in advance. When using tile adhesives, only a thin layer is required, which also saves space for applying cement.

But compared with the cost of cement, the cost of tile glue will be much higher; The level of the tile glue market is uneven, and it is difficult to distinguish between the real and the fake. Inferior tile adhesive will also release harmful gases and endanger human health, so its environmental protection is relatively poor.

Now the quality of tiles is getting better and better, so even if it is a wall tile, the water absorption rate is not so high. Therefore, the water absorption principle of traditional cement mortar can no longer meet the requirements of current pavement. And the tile is getting bigger and bigger, and the tile glue is easier to paste.

Moreover, tile glue is not affected by climate and humidity, and cement mortar is likely to fall off due to thermal expansion and contraction.

The relevant content about whether the tile is glued or cement is shared here, I hope it will have a certain reference value for you. In addition, we should remind everyone that if the tile glue and cement are mixed together to paste the tile, it will affect the effect of the tile glue, so try to use tile glue when laying tiles. If the cost must be considered, the proportion of cement should also be mixed according to the regulations.

This is true, because tile adhesive is more viscous than cement sand adhesive and will not let the tile fall off easily.

It's really like this, such a setup will be better, and the quality is particularly good, and it is also particularly suitable.

It's true, because most people now put tiles on the wall, so if you use tile adhesive, it is not easy to fall off in the later stage, and it will not be hollow.

If you want the floor tiles at home to be firm and durable, not bulging or cracking, on the one hand, you need to look at the quality of the tiles, and on the other hand, you need to look at the paving method. In particular, the adhesive material chosen for installation is also very important. When laying tiles, some workers will recommend that the owners of the community choose to use tile glue to pave the floor tiles of the whole house, this kind of super glue is called high adhesion, which is better than mixed mortar.

But is this the case? Tile adhesive, also known as tile adhesive, is actually the same as mixed mortar, except that it is mixed with a little more super glue. Moreover, it has strong viscosity, light material, and the floor tiles are not easy to fall off after sticking to the wall.

Because of this, it is a new type of adhesive raw material that can replace mixed mortars. Although it has advantages over mixed mortar, it doesn't mean that the whole house will be made with tile adhesive!

The important characteristics of tile adhesives are that they have a strong ability to apply tiles, are leak-proof, and are not easy to age. It is generally used for exterior wall construction, the construction of the project is simple, and the floor tiles should not be soaked in advance. When applying tile adhesive, only a thin layer is required, which also saves space for plastering concrete.

But compared with the cost of concrete, the cost of tile glue will be much higher; The quality of the tile glue sales market is uneven, and it is difficult to distinguish between true and false. Inferior tile adhesives will continue to release harmful substances and harm health, and its environmental performance is very poor.

Nowadays, the quality of ceramic tiles is getting better and better, so even wall tiles are not very absorbent. As a result, the basic principle of hygroscopic absorption of conventional hybrid mortars has long been unable to meet the needs of today's laying. And the floor tiles are getting better and better, and the tile glue is easier to stick.

And the tile glue will not be harmed by climate and temperature, and the mixed mortar is likely to cause the perforated bricks to fall due to heat expansion and cold contraction.

The introduction of floor tiles to use super glue or concrete tiles is here, I hope it will have a certain practical value for you. In addition, we should remind everyone that if the tile glue and concrete are mixed together and pasted with wall tiles, it will affect the effect of tile glue, so tile glue must be applied when laying tiles. If the cost must be considered, the proportion of concrete also needs to be mixed according to the regulations.

When laying tiles, some workers will suggest that the owner choose to use tile adhesive to pave the tiles of the whole house, which is claimed to have a high degree of adhesion and a better effect than cement mortar.

Such a statement is not true, although cement mortar will be more advantageous, but the whole house tiles still have to use tile glue.

I think that's true, mainly because tile adhesives work better and they last longer.

Now people will use tile adhesive when laying bricks, and the tiles will be glued directly, and the effect of sticking out is also very good, which is not visible to ordinary people, and it is very convenient and saves money.

It is very easy to use, compared with cement, tile adhesive is better to use, and the appearance is higher.

I think it is better to choose tile adhesive when applying tiles, because the tile adhesive has a better anti-aging effect, water resistance will be better, and its viscosity is better than cement.

Summary. Hello, I'm glad to answer for you, my answer is <> below

I think it is better to use cement to stick wall tiles or floor tiles, so I personally think it is best to use cement to paste, because the stability of cement is better, and the technology is more mature, and the degree of adhesion is very high, so there will be absolutely no hollowing in the later stage.

Is it better to use cement or cement to mix glue on the tile.

Hello, Pi Tan is happy to answer for you, my answer is as follows<>

I think it is better to use cement to stick wall tiles or floor tiles, so I personally think it is best to use cement to paste it, because the stability of the water tease the mud is better, and the technology is more mature, and the adhesion is very high, so there will be no hollowing in the later stage.

Our tiles are comparatively larger, 80 8.

80 80's.

Hello, I'm glad to answer for you, my answer is <> below

It is more convenient to use cement to bury the glue, but there will be a lot of problems in the future, and there will be hollowing or falling off, so I suggest that the banquet is closed with cement to bury the glue.

Hello, I'm glad to answer for you, my answer is <> below

If it's 80 80, I recommend using AB glue.

Our house is relatively tall, is it easy to fall off?

Hello, I'm glad that the lead hail answers for you, my answer is as follows<>

I think the cement is not as good as cement or AB glue, and I can only stick some more light finger decorations such as bamboo fiberboard.

Is it mixed with AB glue in cement?

Hello, I'm glad to answer for you, my answer is <> below

It doesn't matter if you use cement or AB glue to fight the banquet, the viscosity of these two is greater than that of the cement.

Hello, I'm glad to answer for you, my answer is <> below

Yes, it is generally mixed with a certain amount of AB glue in cement to stick the tiles.

The master bricklayer always suggested, we use cement, we don't understand, which one is better?

What the decoration company gave us was to mix glue in cement.

Hello, I'm glad to answer for you, my answer is <> below

It must be ab glue or cement good, I think he should be lazy to use cement, because the cement is very convenient to go directly without being sensitive, if the wall is relatively high, then it can be cement rent to take the beam with glue is better.

Hello, I'm glad to answer for you, my answer is <> below

Usually it is cement mixed with AB glue, so that the viscosity is the largest.

Hello, I'm glad to answer for you, and my answer is as follows<>

I am the builder of the decoration company, I understand this, under normal circumstances, if you are afraid of falling, then you can add this AB glue in the cement, which can be used to stick tiles. In fact, AB glue is also a kind of tile glue, which is a relatively new and wide decoration material.

In fact, this tile adhesive should be better, do not like to fall off, but also waterproof.

The most important thing is that the thinness of the application is possible, and space saving is possible.

The reason why the master of the decoration likes to use only cement and sand is here:

1. This thing is used more on the exterior wall and less on the interior wall, and many masters don't know how to use it, and it is not as convenient as the old way of cement and sand;

2. Now the quality of the project is really not flattering, many walls are uneven, and they have to be leveled if the old method of cement and sand is used, they paste tiles and even leveling and then tiling about 2-3cm; If you use tile adhesive, it will be expensive; If you level first and change the adhesive sticker, it will be troublesome.

To tell you the truth, I asked the decoration master, I put bricks yesterday, or chose cement. The most important point is that the environmental protection of tile adhesive is slightly worse.

The effect is similar, but if the tiles are more high-end, I recommend using glue.

Of course, it is better to use tile glue.

It is recommended to use Gomex tile adhesive.

Gomex C1TE universal tile adhesive: mainly suitable for all kinds of floor tiles, stone, small and medium-sized wall tiles and sandstone paste.

Gomex C2TE Tough Tile Adhesive: Ideal for wall pasting of large size tiles, vitrified tiles, sandstone and natural stone panels.

Gomex C2TES2 flexible tile adhesive: especially suitable for pasting stone and ceramic tiles on old walls or bricks, micro-vibration substrates, gypsum boards and other special substrates.

Gomex C2T two-in-one mosaic glue: especially suitable for pasting and caulking projects of various paper ceramic tiles, marble mosaics, glass mosaics, etc.

If you want to save costs, you can still use cement for floor tiles.

If you stick wall tiles, it is best to use tile adhesive.

We will find that in the bathroom, the brick joints in the kitchen will be black, which is mold.

General caulk, if the quality is not good, will be like this.

The CG2 color waterproof caulk: especially suitable for internal and external wall tiles, floor tiles, mosaics and all kinds of stone caulk, especially in wet places, can play a mildew and waterproof function.

It's a pretty good brand. You can try.

Now the tiling technology has been improved, and I think the tile adhesive should be relatively better than cement.