How should a water dispenser be disinfected? How to disinfect a water dispenser

Unplug the power supply, remove the bucket, turn on the drinking switch, and drain the remaining water in the cavity of the water dispenser. Expert Comment: The first step in disinfection of the water dispenser is to release all the remaining water in the cavity of the water dispenser.

However, when we open the tap of the water dispenser, we can only release a small part of the water, so there is a big disadvantage in this method. Correct method: Open the sewage pipe behind the water dispenser first and drain the remaining water.

Because the remaining water in the sewage pipe is the key to the secondary pollution of the water dispenser, and then, turn on all the drinking water switches to release water. Hold the alcohol cotton with tweezers and carefully scrub the inner tank of the water dispenser. These parts of the water dispenser are prone to bacterial accumulation due to direct contact with the air.

Scrubbing with alcohol can remove dirt from the top and prepare for the next step of disinfection. Pour 300ml of multi-purpose disinfectant into the inner tank of the water dispenser and soak for 10 to 15 minutes. The capacity of the cavity of the water dispenser is about 2 liters, and only 300 ml of disinfectant can only disinfect the extremely limited space in the cavity of the water dispenser, and such disinfection is ineffective.

Dissolve 300 ml of disinfectant into about 2 liters of water, fill the entire cavity and leave for 10 to 15 minutes. Turn on the drinking water switch and drain the disinfectant. As mentioned above, the drinking water switch can only release a part of the disinfectant, and most of it remains in the cavity, which will become a new source of water pollution if it is not drained.

Correct method: Turn on all the switches of the water dispenser, including the sewage pipe and drinking water switch, and drain the disinfectant. Rinse the entire water dispenser cavity with 1000ml of water, and then turn on all the switches of the water dispenser to release water.

Rinsing with 1000ml of water is not enough and will cause the disinfectant solution to remain in the water dispenser. Rinse the entire cavity of the water dispenser continuously with 7 8 liters of clean water, and turn on all switches to drain the flushing liquid. Scrub the back wall of the water dispenser switch with a rag.

Expert Comment: When using a cup to hold water, it is easy to touch the back wall of the water dispenser switch, so it is not just a simple decontamination treatment here. Do-it:

Scrub the back wall of the switch with alcohol cotton. Put the bottled water, the disinfection staff turn on the switch, put a glass of water and drink it all, indicating that the user can drink it with confidence. After the disinfection of the water dispenser, there may be a trace amount of disinfectant remaining, so you should not drink it immediately.

Do: Put a glass of water and smell if there is any chlorine smell. If so, put water in it until you can't smell chlorine before you can drink it safely.

When disinfecting the water dispenser, turn off the power first, remove the bucket on the water dispenser, and discharge the remaining residual water in the water dispenser through the sewage pipe. The remaining water in the water dispenser is the key to secondary water pollution, so be sure to remove the residual water. It is not recommended to use chemical drugs to disinfect the water dispenser, and it is unsafe to use chemical drugs for disinfection, and it may not only fail to disinfect the water dispenser, but also aggravate the pollution of the water dispenser, affecting people's health.

When disinfecting the water dispenser, you can use alcohol to disinfect, and the disinfection effect of alcohol is very good. When using alcohol disinfection, use tweezers to clamp the cotton sticky to the alcohol to scrub the inner tank of the water dispenser, the inner tank of the water dispenser is the most likely to accumulate bacteria, so you must be careful when cleaning. After cleaning the inner tank, you need to use the disinfectant, first dissolve the quantitative disinfectant in the water and pour it into the inner tank of the water dispenser and let it stand for about 10 minutes.

When the time is up, turn on the switch of the water dispenser (note that all the switches are on/off) and drain the disinfectant. After the disinfectant is discharged, it does not mean that our disinfection process is over, and then we should use clean water to rinse the water dispenser, clean up the residual disinfectant in the water dispenser, and rinse it several times if you feel that the cleaning is not clean once. The last step is to use alcohol to clean the faucet, and the whole process of disinfection of the water dispenser is completed, is it very simple.

First, open the sewage pipe behind the water dispenser, drain the remaining water (the remaining water in the sewage pipe is usually the key to the secondary pollution of the water dispenser), open all drinking water switches and empty the residual water; Dissolve 1 tablet of "Shu Yikang Decontamination Effervescent Tablets" specially used for disinfection of water dispensers in about 2 liters of clean water, and use part of its disinfectant to scrub the inner tank and the inside and outside of the lid of the water dispenser; The rest of the disinfectant fills the entire cavity, and after leaving for 10-15 minutes, turn on the switch of the water dispenser, including the sewage pipe and drinking water switch, and drain the disinfectant; Continuously rinse the entire cavity of the water dispenser with 7-8 liters of clean water, and then turn on all switches to drain the flushing liquid; Finally, the back wall of the switch is scrubbed with disinfectant to complete the entire disinfection process.

If you want to disinfect the water dispenser, you can use the disinfection function of the water dispenser to disinfect, find the disinfection rotation button on the side of the water dispenser, and adjust the button scale according to the disinfection time; You can also disassemble and soak some parts of the drinking water machine, especially the blind water tank of the water dispenser, which needs to be repeatedly soaked in chlorine dioxide for disinfection and sterilization.

At present, most of the water dispensers on the market have their own disinfection function, which can generally be used for daily disinfection or care. Find the disinfection rotary button on the side of the water dispenser, adjust the button according to the time you want to grind the bridge to disinfect, the water dispenser can be disinfected for 5 minutes after one month of use, and wait for the water dispenser to disinfect itself after adjusting the scale.

Manual disinfection is more suitable for detachable water dispensers, so that the disinfection can be more thorough and comprehensive, especially for old-fashioned water dispensers, because of the aging of parts and gaps, resulting in dust and bacteria falling into the water dispenser, the inside of the water dispenser needs to be opened for comprehensive cleaning and disinfection, so as to prolong the service life of the water dispenser.

Open the faucet of the water dispenser, empty the water dispenser's water tank, pour in chlorine dioxide disinfection water and soak for 10 minutes, then clean, and rinse with clean water repeatedly, which can effectively clean the scale in the water tank and carry out disinfection and sterilization. Disassembling the parts of the water dispenser and soaking the parts in boiling water for 5 minutes can also achieve the purpose of disinfection.