How to make a handmade car

Material preparation: an old hard cardboard box (such as a toy box, snack box), plasticine.

Latex, 2 small wooden sticks, 1 ruler, 1 utility knife. Production process:

1. Observe the appearance of the box, if there is a beautiful appearance, it can be used as decoration. The smiling face shown below.

3. Cut out the scrap material to a good size to make the head cover.

4. Dig out a front windshield opening for the front hood.

5. Paste transparent plastic with glue as the front glass.

6. Paste the front cover on the body, and the body also dig out the left and right window glasses and paste transparent plastic.

7. Make four wheels out of plasticine.

8. Wear the wheels with wooden sticks and install them on the body, and the carton car is made. Precautions 1: Tie a few toothpicks in the plasticine used to make the wheel, and the wheel will be more stable. 2. The decorative pattern of the body should be fully used, and attention should be paid to the cutting position.

3. The carton should be selected to be a bit harder, so that the body frame is more stable.

Here's how:Prepare materials: toothpaste box, four vial caps, double-sided tape, scissors, plasticine, straw.

The first step is to prepare all the equipment you need.

The second step is to cut the toothpaste box to the one shown in the picture.

Fourth, use the excess pieces of paper to make the head and tail of the car.

Step 5: Stuff the plasticine into the cap and use the straw as the axle.

Step 6: Fix the wheels on the body.

The seventh step is completed.

Simple way to make a handmade car:

Materials required: colored paper, paper tube (after the toilet paper is used up), 4 caps for mineral water bottles, wooden sticks (remove the cotton swab head), double-sided tape, hot melt glue gun, scissors, etc.

Step 1: Make the axle, cut a piece of colored paper shorter than the length of the wooden stick, roll it into a small paper tube, as shown in the figure below, pay attention to the wooden stick after rolling, the wooden stick should be able to move.

Step 2: Make the body, cut the colored paper suitable for the paper tube, wrap the paper tube, and then use your imagination to decorate the body.

Step 3: Wheel making, drop the hot melt glue in the center of the bottle cap, place the small wooden stick in it, wait for the glue to dry, put it into the small paper tube, and the center of the other bottle cap also drip into the hot melt glue, and then glue the other end of the wooden stick, in the same way, make two, and the wheel is finished.

Step 4: Drip hot melt glue on the axle, and then glue the DIY body to serve.

Prepare materials: paper boxes, colored paper, toothpicks, scissors, tape.

5. Finally, stick the wheels to the bottom of the car.

Prepare the materials:

Toothpaste box, four identical vial caps, double-sided tape, scissors, plasticine, straw Specific steps:

1. Prepare the materials that need to be used, it should be noted that the four bottle caps as the wheels of the car should be the same, which can increase the aesthetics of the car.

2. Cut the toothpaste box according to the following **, pay attention to the left and right sides to be the same size.

3. Glue double-sided tape on the edge of the top piece, fold it down, and glue it tightly.

4. Use the excess paper cut out to make the head and tail of the car. See ** below.

5. Stuff the plasticine into the bottle cap and pinch it flat. Use a straw as an axle and insert it into plasticine.

6. Glue the two pairs of wheels under the body with transparent glue.

7. Check if there are any unsightly places and make adjustments, so that the handsome car is ready.

1. First of all, prepare a toothpaste box, corrugated paper, bottle cap, double-sided tape, colored pencils, and scissors.

2. Then cut the toothpaste box in half according to the edge creases.

3. Then cut it at a right angle to facilitate the front of the car;

4. The cut right-angle effect is shown in the following figure:

5. Then use scotch tape to attach it, as shown in the figure below

6. Cut out a long strip to make the front nose of the car, and then cut out a long strip to make the rear wing of the car;

7. Then use the bottle cap to draw 4 circles on the paper skin, the four wheels of the car, as shown in the following figure:

8. Then use double-sided tape to stick the four wheels on both sides of the car, as shown in the following figure

9. In this way, a toddler's handmade car is ready.

1. First of all, prepare the double-sided tape, bottle caps, corrugated paper, waste cartons (taking common toothpaste boxes as an example), colored pens, clay, and scissors required for DIY cars.

2. Then cut the toothpaste box to 1/2 length with scissors, as shown in the figure below

3. After that, cut one end of the cut half of the toothpaste box and cut a right-angled triangle along the edge;

4. The effect of cutting the right triangle is shown in the following figure:

5. After that, press down on the top end and glue it with adhesive tape to make a car head, as shown in the figure below

6. After that, cut out two long strips, which are used as the front nose and the rear wing of the car respectively, as shown in the figure below

7. Then cover the corrugated paper with a bottle cap to draw a circle, and cut out a circle as a wheel, as shown in the following figure:

8. Then use double-sided tape to stick the wheels on both sides of the car, as shown in the figure below

9. Such a car is DIY.

Here's how to make a handmade car:

1.Prepare materials and tools

To make a handmade car, you need to prepare some materials and tools. Commonly used materials include cardboard, wooden strips, rubber bands, plastic tires, etc. In terms of tools, you need to prepare scissors, glue, small hammers, nails, etc.

Choosing the right materials and tools according to the design requirements ensures that the production process can be completed smoothly.

2.Designed and conceived by Yousun

Before you can make a handmade car, you need to design and conceive. The shape and structure of a car can be designed by drawing a sketch or using modeling software. Considering the functions and characteristics of the car, how to arrange the layout of components such as chassis, body and wheels is an important nonsense step.

Meticulous design and conception can provide guidance and direction to the production process.

3.Fabrication of chassis and bodywork

The first step in making a handmade car is to make the chassis and body. Using materials such as cardboard or wood strips, the corresponding parts are cut and glued according to the sketches of the design, and assembled into the basic skeleton of the chassis and body. Make sure the chassis is structurally stable and leave proper space for other components.

4.Install the wheels and power system

The next step is to install the wheels and powertrain. Secure the plastic tires to the bottom of the chassis to ensure smooth turning. Choose the appropriate bearings or screws to secure the wheels and ensure their stability.

If you want to make the handmade car have power, you can use rubber bands, batteries, motors and other components to install them inside the chassis.

5.Decoration and adjustment

The final step is to decorate and adjust. Depending on your preference, you can add colors, stickers, or patterns to your handmade cars. In addition, it is necessary to check whether the connection of the individual components is firm, whether the wheels are rotating smoothly, whether the power system is operating properly, and make the necessary adjustments and corrections.

Summary:

Making a car by hand requires the preparation of materials and tools, design and conception, fabrication of the chassis and bodywork, installation of wheels and powertrain, and finally decoration and adjustment. This process requires patience and meticulousness, and it is also a process of exercising hands-on skills and creativity. By making handmade cars, you can not only gain a sense of accomplishment in doing it yourself, but also develop an interest in mechanics and engineering.

1. Prepare all the materials as shown in the figure below:

2. Cut the cardboard into a rectangle and use it to make the chassis of the car.

3. Draw the chassis of the car with a pen, and the front end is used to hang rubber bands.

Fourth, after the outline, use scissors to subtract the excess part, and the tray of the trolley is done.

5. Use extra cardboard to draw out the four wheels.

6. Use scissors to cut out the drawn wheels, if you feel that the wheels are a little thin, you can cut 4 more and then glue every two into one.

7. Cut out 4 small sections of the ballpoint pen refill.

8. Put the cut ballpoint pen refill on two bamboo sticks, and each set of two pies.

9. Tie a rubber band to one of the bamboo sticks and glue it with hot debate booth melt glue.

10. Fix two bamboo skewers at both ends of the cardboard base of the car.

Ten. 1. Install the finished 4 wheels on the car, and then fix the wheels.

Ten. 2. Hang the rubber band at the other end of the base of the trolley as the power system of the trolley.

Ten. 3. Now that the production has been completed, the rear wheels of the car are constantly rotated backwards to store energy, and then put it on the ground and it will run.

Simple steps to make a handmade car:1. Prepare a toothpaste box, scissors, double-sided tape, transparent glue, pen, and ruler.

2. Use a ruler and a knife to cut the toothpaste box into two sections, one end of the carriage and the other end of the car, and the ratio is 3 to 1.

3. We use a pen and ruler to draw the diagonal line of the front part of the car, and then use a knife to cut it.

4. Fold it and paste it with double-sided tape and transparent glue at both ends, so that the front of the car will come out.

5. We cut off one end of the rear of the car with scissors, and pasted the front and rear of the car, which basically looks like a car. Draw the tire with a pen and cut it out.

6. Decorate the windows of the car according to your preferences. You can use colored pens to draw a pattern, cut it out and paste it, and the final result is like this.

Here's how to make a car by hand

Material preparation: colored paper, paper tube (after the toilet paper is used up), 4 mineral water bottle caps, wooden stick (remove the cotton swab head), double-sided tape, hot melt glue gun, scissors, etc.

1. Make an axle, cut a piece of colored paper shorter than the length of the wooden stick, roll it into a small paper tube, and pay attention to the fact that after rolling, the wooden stick should be able to move.

2. Body production, cut the colored paper suitable for the paper tube, wrap the paper tube, and then use your imagination to decorate the body.

3. Wheel production, the hot melt glue is dropped in the center of the bottle cap, the small wooden stick is placed in it, after the glue is dried, the small paper tube is set, and the hot melt glue is also dropped into the center of the other bottle cap, and then the other end of the wooden stick is glued, in the same way, two are made, and the wheel is made, and the effect is shown in the figure below.

4. Drip hot melt glue on the axle, and then glue the DIY body to serve.