The antiseptic factory invites a knife sharpener master, is there a preservative wood to recruit a k

According to the following list of special trades, spinning workers belong to special trades.

Textile industry chemical fiber toxic and harmful types of work:

1. Carbon disulfide fabricator.

2. Calcium sulfite liquid medicine manufacturing worker.

3 cookers 4 washers.

5. Bleaching workers 6. Sulfur chemical industry.

7. Plate and frame filter.

8. Spinning worker, 9. Filament twister, silk thrower.

10 filaments to the head.

11. Filament hanging wire.

12 cellophane fabricators.

13 Iron-chromium salt fabricators.

14 Cotton linter preparer.

15 Bleach Liquid Makers.

16 Unloading logs.

17 Log porters.

18 Turner.

19 Carpenter.

20 Carbon disulfide storemen.

21 Carbon disulfide preservation worker.

22 Staple fiber post-processing workers.

23 Carbon disulfide ** work.

24 internal precision workers (spinneret finishers).

25 External Precision Workers.

26 Power wire parts replacement.

27 Waste Wire Cleaners.

28 Strong bobbin finisher.

29 Powerful wire metering pump assembler.

30. Strong wire grader, loading and unloading wire worker.

31 Strong Silk Packer.

32 strong silk beginning, double twist stop lathe.

33 Strong silk weaving cloth stopper.

34 Strong silk glue worker.

35 Sulfonation machine, spinning machine maintenance worker.

36 Acid Station Acid Bath Worker.

37 Acid Station Security Worker.

Hello, it is recommended that you go to the regular talent recruitment** to inquire about the recruitment information! You can also check out the local talent market! But be careful!

Have a great day!

In this kind of recruitment, the revelation is often posted at the gate, and it is recommended that you go around, or go inside to ask, look for a job, and ask more without shame, only in this way can you find a suitable job. Good luck, remember.

Do you sharpen knives and change knives?

Hello, I will tell you responsibly: not a special type of work!

The silk reeler is very hard, especially the reel, standing for 8 hours a day, not to mention, and his hands are still soaking in hot water.

However, there is no harmful and toxic working environment, and there is no particularly heavy manual labor workload, so it is not a special type of work.

Special types of work refer to: engaged in underground, high-altitude, high-temperature, particularly heavy physical labor or other work harmful to physical health, the retirement age is 55 years old for men and 45 years old for women.

Not count. But it's hard.

He uses oil stones, which are more lubricating than water, and are not easy to scratch, and are brighter, because the viscosity of oil is greater than that of water, and it is easier to form a lubricating film.

The grinding stone is an oil stone, which is finer and brighter when ground with engine oil.

It depends on what kind of whetstone is used.

Epoxy zinc phosphate paint anticorrosive coating Tianjin Qirui paint production and sales, before the construction of the substrate polished clean pretend to be rust removal hall stool field, if the cold galvanized paint is too thick, must be diluted to the required consistency with a special thinner after construction. Stir well before rough use.

If the epoxy zinc phosphate paint anticorrosive coating is too thick, it must be diluted to the required consistency with a special thinner material before construction. Stir well before use. I think the Qirui paint manufacturers are very good at early production, you might as well try it slowly.

There are two reasons for this: this streak is very similar to the chatter mark, which is caused by the high vibration of the grinding wheel of the grinding machine.

If the grinding workpiece requires high precision, it is best to use the on-site grinding wheel dynamic balancer such as Taiwan Hongfuxin PY2700G to test, the spindle vibration, if the vibration is too large, it is best to adjust the grinding wheel dynamic balance online, and the general grinding machine vibration is controlled within the international standard.

The black lines may be burned as a result, that is, there is no grinding fluid, so it is best to try to open the grinding fluid.

The spindle is not shaking, is it too much to eat the knife, and burn the knife.

Sharpen your knife and watch it often, and don't sharpen it blindly.

First of all, there should be two whetstones, one is rough like the one you posted, and the other is a little thinner.

Sharpen on the rough surface first, and then move on to the fine whetstone.

Always look at the blade with your eyes, and if the handle is facing you, you will see a white line in some places that is black and in others. The black is the well-proportioned place where it is polished, and the white line is rolled on one side, and then it is ground back.

Oh my God, you're really talented, it's strange that you can grind so dullly.

Are you **? If you're from Xi'an. I'll help you sharpen your kitchen knife, guaranteed profits

Tilt 45 degrees grinding, both sides.

Don't sharpen the kitchen knife randomly, teach you the correct way to sharpen the knife, and tell your family after reading it!

The blade of the knife sharpens the edge of the axe, and the blade of the chisel cannot be sharpened into the edge of the chisel.