What are the tips for sticking wallpapers yourself? What are some tips when it comes to wallpapering

With the improvement of people's living standards, the requirements for the comfort and taste of the living environment are getting higher and higher. Wallpaper is increasingly used for decoration. Many people also like to put wallpaper in person, but in fact, it is not difficult to put wallpaper.

Just grasp a few key points. Next, teach netizens how to put wallpaper. If you are interested, please come and see me.

The method of applying wallpaper yourself, fill the holes in the wall with putty, and level the walls with a scraper. After measuring the size of the wall, measure the wallpaper based on the wall area, paying attention to the length of the wallpaper, which is 5 cm more than the actual veneer.

Add water to the powdered wallpaper adhesive and mix the regular wallpaper into it. Adjust the foam wallpaper to 1:2 and paste it with a wallpaper-specific adhesive that does not need to be modulated, or evenly apply a wallpaper-specific adhesive that is easy to be applied by a roller brush on the back of the wallpaper.

Then place the wallpaper against the wall and use a wooden handle to paste it from top to bottom, from the corners to the inside, to level the wallpaper. When encountering a power switch or outlet, cover it with wallpaper first, smooth it with a wooden handle, then use a utility knife to draw a cross on the upper corner, use a scraper to support the edge of the switch, and use a utility knife to cut off unnecessary parts.

When the printed wallpaper is meshed, find the matching position of the pattern at the junction of the two wallpapers. Stack, paste about 12 cm wide, support with scratches until the entire wallpaper is fully aligned, and then cut the overlap into blades. When pasting wallpaper, pay attention to pasting from top to bottom.

If you find an uneven float, you can soak it with a towel and re-level it with scratches. Handle the wallpaper around doors and windows. This is the same as the wallpaper treatment for the power switch.

After pasting the wallpaper, reinstall it with the original device and you're done. Carefully apply the wallpaper with a spatula, over the convex corners, but not on other walls. Sweep your hand through the corners of the convex wall from top to bottom, creating wrinkles and drawing a vertical line from the ceiling to the floor at a distance of centimeters from the convex wall.

Use a utility knife to cut the wallpaper along the vertical line above, guiding it with a ruler. Carefully pull out the remaining wallpaper, place it on the bench, and keep it for use. Flatten the stretched part with a seam pressure wheel, and then apply adhesive to the wallpaper where the lid is attached.

Stick it from top to bottom, pay attention to the strength, etc. Pay attention to the wallpaper yourself to be sure to start pasting from top to bottom, so as to avoid the situation that the wallpaper deviates when pasting; It is also necessary to pay attention to the strength when pasting, otherwise it will cause the wallpaper to stretch and paste unevenly.

When pasting wallpaper by yourself, first of all, you must measure the size, cut the wallpaper to the appropriate specifications, and then adjust the glue well, evenly wipe it on the wall, and then gently align and paste the wallpaper, and then use a cotton rag to smooth it out vigorously to remove the bubbles inside, especially the edges and corners, which must be smoothed, so that it will appear more flat.

When you paste the wallpaper yourself, don't tear out the wallpaper all at once, you should paste it slowly, you can choose a scraper, so that the wallpaper you paste is also very smooth.

Wallpaper is easy to wrinkle if you are not careful, so you need some tips when pasting wallpaper, first of all, you must clean the wall, it is best to brush the wall with a layer of varnish, so that the wall can be hardened, and then paste from top to bottom, it is best to use a professional scraper to ensure that the paste is relatively flat, so it is easy to paste beautiful wallpaper.

Before pasting the wallpaper, first of all, the wall should be cleaned up, the wall skin should be shoveled off, and then cut the appropriate size, apply glue, paste the wallpaper on the wall, after the wallpaper is pasted, close the doors and windows, and then put a pot of burning charcoal in the room, which can neutralize the smell of the wall glue.

Some materials should be prepared, and the wall skin should be removed and cut to a suitable size, some places should be painted, and some glue should be applied, and it should be paved and pasted so that the effect of sticking out is better, and it should be cleaned after pasting.

1. Wall treatment: use a scraper and scrape off the wall impurities, floating soil, and pave the holes and cracks with gypsum powder. It is recommended that you use varnish or varnish to be better, but varnish is not environmentally friendly, so that the wall is firm and the wallpaper will not fall off.

2. Cutting wallpaper: first measure the height of the wall, and then cut the length of the wallpaper, and consider the symmetry of the pattern for the flower wallpaper, so the cutting length should be increased according to the actual situation, usually 8 to 10 cm longer. 3. Coating glue:

Brush the wallpaper glue on the back of the cut wallpaper with a brush, pay special attention to the edges around must be coated with glue, so that the glue can be posted after completely penetrating the bottom of the paper, each time several pieces of wallpaper are painted, and posted in order.

1.When pasting wallpaper, do not build during the rainy season. The room temperature should be higher than 5 degrees Celsius, the temperature should not change significantly, and the air humidity should be less than 85.

After stripping the putty, tape, all walls need to be treated, the walls must be smooth; Drywall, wall color development stone color bright background when the end of the screen shows a clean surface, color matching.

2. Because the wallpaper is eco-friendly, it is inStick your own wallpaper tricksPacked with the glue we use, and there will be harmful substances such as formaldehyde. In order to be safer and more environmentally friendly, we will use environmentally friendly adhesives for packaging. wallpaper glue can not be adjusted early to avoid dry glue.

When you go to the wallpaper, pay attention to whether the pattern of the wallpaper is aligned or not. You can put the numbers on the back of the wallpaper.

Stick your own wallpaper tipsWe apply glue to the back of the wallpaper, then fold half of the wallpaper and leave it open for about 10 minutes. Wrapping from left to top, this pattern wrapping glue spills out of the wrapper, wipe the screen when the wrapper aligns.

Once the wallpaper has been placed, a scraper or flat brush should be used to flatten the wallpaper.

4. After laying the wallpaper, the doors and windows should be closed. When you open the doors and windows, the wallpaper will immediately appear as a drum. Usually, the wallpaper dries for 3 days. In everyday life, it is best to wipe the surface of the wallpaper with a dry towel or vacuum cleaner every 2-3 months.

1.The plaster substrate must be protected from cracking.

If the floor of the original wall is drywall, thenStick your own wallpaper tipsBe careful to block moisture. The first step is to put all the self-tapping screws into the anti-rust paint to prevent rust and prevent the wallpaper from corroding. This is followed by gypsum shrinkage and crack prevention, white latex powder filling gypsum, gypsum board gasket.

Experts here emphasize that due to the use of putty gypsum powder, gypsum powder and gypsum material are the same, expansion and contraction coefficients are the same, if putty is used, other shrinkage factors, will also lead to cracking.

Stick your own wallpaper tipsIn order to prevent cracks, dry gypsum powder should also be sewn and bandages should be pasted. Generally, there are good cloth, kraft paper, mesh gauze. Due to the narrowness of mesh gauze and weak adhesion, it is rarely used nowadays.

After processing the patch, perform a polishing putty operation and then place the wallpaper normally.

2.Wooden floors prevent deformation.

If you need toStick your own wallpaper tipsWhat to do on a wooden board? First of all, a thin layer of paint must be applied to the board to prevent the wood from deforming due to moisture. In the case of cracks, the joints are replaced with putty instead of plaster powder.

Due to its high hardness and stability, there is no problem of shrinkage and expansion. The next step is putty. Apply a thin layer of white latex and water to the putty in a ratio of 10 x 1778 1.

In fact, it is as thin as paper and fills in the unevenness of the board. Putty should be able to stick to the board, and then it can easily lead to wallpaper. After sanding and reapplying a thin lacquer (solvent-based or water-based paint), it is possible to prevent the deformation of the wallpaper with wood problems.

Once you have done this, you can perform the normal wallpaper task.

The materials that need to be prepared for wallpaper include: measuring instrument ruler, wallpaper, glue, paper cutter, brush, and scraper.

1. Use a measuring instrument or ruler to mark the wall, and align the mark when pasting the wallpaper.

Second, then brush a large area of glue on the wall, you can brush part of the paste.

3. Paste the wallpaper according to the marked mark.

Fourth, try to reserve more wallpaper for the switch part, and then cut it with a paper cutter to avoid warping.

5. Where there are bubbles, you can scrape a few more times with a scraper to remove the bubbles.

The steps of the wallpaper method are as follows:

1. Crop wallpaper:

Measure the height from the top of the wall to the baseboard, then crop the wallpaper. Do not cut the flower wallpaper by about 10 cm according to the height of the wall, and use it for trimming up and down; The symmetry of the pattern needs to be considered for the flower wallpaper, which needs to be cut and numbered after planning more than 10 cm, so as to paste it in order.

2. Brush oil and scrape:

Brush the primer, evenly brush the alkyd varnish on the wall with a moderate thickness, and scrape putty twice on the wall. After the putty is dried, polish the wall with sandpaper to grind off the uneven particles to make the wall smooth and flat; Cover oil, paint the wall evenly again with clear oil, without being too thick.

3. Glue: In order to ensure that the paste is firm, the back of the wallpaper and the wall should be brushed, and the glue should be evenly painted, and the edge can not be wrapped and piled up to prevent the wallpaper from being soiled. Glue the wall 30 mm wider than the wallpaper. After brushing the back of the wallpaper, fold the glue side and leave it for 5 minutes.

4. Pasteing: The principle is first vertical and then horizontal, first up and then down, first high and then low. When pasting the first piece of paper, find the baseline at the corner of the wall, gently flatten it with your hands from top to bottom, from the middle to both sides, and then scrape with a scraper to make the wallpaper and the wall solid.

When pasting the second piece of wallpaper, overlap the overlap with the first sheet by 20 mm, use a wallpaper knife to cut off the overlapping part, remove the remaining part and scrape it flat with a scraper.

5. Paste wallpaper:

After applying the wallpaper glue evenly to the wallpaper with a roller, leave it for a while for thicker wallpaper. When you start to apply wallpaper, for the seams, squeeze the two sides of the adjacent wallpaper together so that they fit, then press the seams with a scraper, and clean the extruded glue. After the wallpaper is pasted, use a scraper to roll out the wallpaper from top to bottom.

Many times, the wallpaper we post is either uneven or uneven. In response to this problem, the master talked about some of his methods, come and listen to it!

Remove the wall skin: Be sure to remove the original paint and other things, fill up the cracks in the wall with plaster powder, and apply a bandage after leveling.

Cut the wallpaper: Measure the height of the wall with a ruler and cut the wallpaper. There are two situations here, one is that the pattern of the wallpaper does not need to be aligned, in this case, the wallpaper is cut 5-8 cm more; There is also a pattern of wallpaper that needs to be aligned, in which case it needs to be cut by 8-10 cm.

Glue coating: When gluing the back of the wallpaper, you must pay attention to the edges around it must be coated with glue to ensure quality. The painted wallpaper should be folded and placed for 5-10 minutes without external force to prevent creases. After the liquid has completely penetrated the bottom of the paper, it can be posted.

Wallpaper construction: Generally the first wallpaper is posted on the side of the door or in the dark corner from top to bottom, with a scraper from top to bottom, from the inside to the outside, gently scrape the wallpaper, squeeze out bubbles and excess glue, so that the wallpaper is flat and close to the wall.

Clean. Use a sharp blade to cut off the excess wallpaper, and then use a sponge dipped in water to completely wipe off the glue remaining on the surface of the wallpaper to prevent the wallpaper from turning yellow. After the wallpaper is dried, if there are bubbles on the surface, inject glue with a syringe and then flatten it.

2. If the wall is very high, the workbench needs to be erected, and the workbench is required to have a smooth surface and be easy to scrub.

3. Mix the adhesive according to a certain amount of ratio and prepare it for later use.

4. Two buckets for cleaning paper towels, and two towels for wiping wallpaper glue.

5. Prepare wallpaper knives, brushes, rollers, rulers, plastic scrapers, elastic tools and line pendants.

After the basic preparation is completed, the next step is to start putting the wallpaper, the steps are as follows:

1. Brush the primer with an environmentally friendly varnish solution, etc., and paint the surface of the base layer. It is also possible to brush the base film, but varnish is the best option.

2. The frame elastic line should be arranged according to the wallpaper format in the indoor front facing the indoor dead corner, the male corner should be wrapped, and the yin corner should be overlapped, and the vertical line should be bounced according to the frame plan, and the number is indicated as the baseline of the paste.

3. Cut the paper according to the size of the wall frame, cut the paper according to the requirements of the wallpaper pattern parquet, compile the corresponding number, reserve 30-50mm She at both ends, and lay it flat for later use.

4. Wipe the workbench with adhesive first, flatten the back of the cut wallpaper upwards, evenly brush it with a large flat brush or roller, and press the upper one-third, the lower two-thirds, and roll the glue surface into a cylinder for posting. Do not brush glue on the back of wall cloth and wall felt to avoid polluting the front, and only brush glue on the wall.

5. Paste the upper part of the wallpaper after brushing, paste it on the wall, stick it vertically (horizontally) on the wall (ceiling) along the baseline, scrape it flat with a plastic scraper or brush, drive out bubbles and excess adhesive, wipe the wallpaper seam clean with a clean towel, and finally cut off the upper and lower excess parts with a wallpaper knife.

If the natural edge of the wallpaper of the flower, then the paper edge of the flower can be strict; If the natural edge is uneven and cannot be seamed on the natural edge, the seam is glued with the knife drawing method. (That is, the two pieces of paper are glued to a little overlap after the flower, cut off with a long ruler rod and a wallpaper knife along the middle line of the overlapping part, tear off the two paper edges that have been cut, and scrape the paper seam with a scraper, and it can be tight).

The corners of the yang corner are compacted, the corner of the yin corner is seamed, and the seam head is left on the backlit side. Note that the wall cloth and felt can not be pasted on the back of the knife, if the edge is not neat, should be cut straight with a wallpaper knife before the wall sticker.