The easiest way to drill and punch holes, the formula for drill drilling

Platoon drill drilling:

1. Classify the plate according to the specifications and sizes, and select the panel, side plate, etc. before punching, and the plate must be handled gently.

2. Customize the sub with the plate size with the largest number of widths.

3. First use flat drills and vertical drills to beat all the big flat buckles, after the same system is drilled, if you need to mobilize the system, the operation is as above after adjusting the hole position.

4. Take the width of the panels on both sides of the drawer as the size benchmark, and customize the left and right subs; The two side panels are thick and leather together and placed in the middle position to punch holes, and the left and right panels of drawer panels are enlarged by 10mm and then placed on the platform to punch holes.

5. Every time the system is transferred or the drill bit is replaced or the drill button is switched, the machine must be self-checked, and when the machine is abnormal, the emergency stop button should be pressed immediately and shut down in time.

Introduction to drill rows. Drill row and row drill are related to drilling, just from the literal point of view to know that these are two different products, first of all, the drill row is placed in the drill bit for work, and there are 21 drill rows, 22 drill rows, 11 drill rows, 3 drill bags, multi-hole drill rows. Its principle is to fix the drill bits together to facilitate drilling processing, which can play a role in batch drilling of products.

1. Percussion drill: This is a tool commonly used to punch holes in the wall, with good drillability, and harder walls can also be drilled.

2. Use a wooden drill to punch holes: You can also use a wooden drill to punch holes, and add an iron nail drill bit at the top of the drill wood to punch holes in the wall, which is very simple.

3. Masonry hammer: If you don't have an electric drill, you can try a masonry hammer, which can punch holes in both the wall and the stone.

1. Place the plates.

According to the classification of specifications and sizes, the panel, side panel, etc. must be rolled before punching, and the plate must be handled gently 2. 3. First use flat drills and vertical drills to beat all the big flat buckles, after the same system is drilled, if you need to mobilize the system, the operation is as above after adjusting the hole position. 4. Take the width of the panels on both sides of the drawer as the size benchmark, and customize the left and right subs; The two side panels are thick and placed together and placed in the middle position to punch holes, and the large reeds made on the left and right sides of the drawer panel are increased by 10mm and then placed on the platform to punch holes; 5. Every time the system is transferred or the drill bit is replaced or the drill button is switched, the machine must be self-checked, and when the machine is abnormal, the emergency stop button should be pressed immediately and shut down in time.

6. After punching the hole, put all the plates on the trolley, do not fall, and then stack them together according to the size of the plates; 7. Turn off the power of the drill row and blow the saw foam on the socks on the machine.

Summary of rhinestone drilling skills:

What to do if the drill bit gets stuck!

1. Outside the wall, make a small hole inward. That is, two heads to fight. For example, if you drill 100 holes, the whole wall is 400 thick, and you can drill at a depth of 200 points, then use a small drill bit outside the wall to punch 200 deep, and use a steel drill to smash out.

2. If it is a high-rise building or the ground, there is no condition to fight. At this time, the lead screw is used, and the lead screw is screwed in from the drill bit. Then use the hammer to hit the drill bit, and twist the lead screw while knocking.

3. Drain holes on the side of the road. If the amount is large, you can use rhinestones, with screws.

It is fixed on a base made of channel steel. Punching, saving time and effort.

4. Time-saving and labor-saving tips for using hand-held rhinestones.

Find a manufacturer to customize the drill bit. Machining a "short and fat" drill bit. A large drill bit of more than 300, 370 high, exhausting people with hand-held rhinestones. The solution is to reduce the height of the drill bit by half, 200 high, which is much more comfortable.

5. What should I do if it is not good to drill a large hole with a hand-held rhinestone?

For example, if you hit a diameter of 300, draw a 300 circle on the wall, and make 4 holes in 25 holes on the inner edge of the inner circle of 290, about 6 cm deep, 1 at the top and bottom, and 1 on the left and right. Then, nail a wooden wedge. Try it by putting the drill bit on a wooden wedge.

6. How to fight dry without adding water.

The walls must be dry, not damp. When drying, there is a new water drill bit, try to use a new water drill bit, too old is easy to chuck.

7. The automatic water supply pump of the water drilling rig saves time and effort with things, and you can search for a treasure by yourself.

8. Fight cattle across the mountain. Double-wall punching method. Sometimes, the spacing between buildings is 300-500 mm.

Rhinestones plus drill bits, with a length of almost 800 mm. Therefore, where the rhinestone is less than 800 mm, it cannot be put in, and it is impossible to punch holes. The solution is to make a 51 mm hole in the center point and open the head wall.

The extension rod extends into the 51 mm hole, and then screws on the water drill bit to punch the hole.

9. The center of the drainage hole of the squatting toilet is not less than 540mm from the wall: the hole is 600.

The center of the drain hole of the sitting toilet is not less than 420mm from the wall, and the hole is punched at 450.

The height of the sitting surface of the sitting toilet from the ground is 300mm:

The edge of the basin is about 800mm from the ground;

The upper edge of the bathtub is not more than 520mm from the ground

10. The desktop rhinestone punching is unstable. Solution: Buy a large expansion tube.

11. Skillfully unload the extension rod. Sometimes, the extension rod and the extension rod, or the drill bit, are too tightly tightened to remove it, and the board is screwed out. What to do, you can pad the extension rod on the stone, and hit the screw buckle with a hand hammer, that is, 3 cm away from the side, which can relieve the strength.

While beating, turn at the same time.

12. The smaller the diamond particles, the sharper they are. However, those drill bit manufacturers don't think so. In addition, if the diamond particles can be broken and used to make drill bits, it will be extremely sharp.

13. The carbon brush of the desktop rhinestone can be replaced by the carbon brush of the hand-held rhinestone. But use it flat. There are few places that are not quite suitable, grind it.

After the hole layout is completed, the drilling rig is fixed with a steel pipe support system on the pre-drawn drilling line, and then the ejector rod is rotated, and the ejector rod is firmly pressed to make the drilling rig reliably fixed. If the ground is partially uneven, it must be padded with a wooden wedge or plank to make it stable, and then plug in the water inlet pipe (the water source is placed outside the embedded pile). After the rig is fixed, connect the power supply and install the leakage protector.

Before drilling, a steel plate casing should be buried to fix the pile position to prevent the orifice from collapsing. The gap between the casing and the hole wall is filled with clay to prevent water leakage, the inner diameter of the casing should be 200mm larger than the diameter of the drill bit, the depth of burial, and the upper mouth is 400mm higher than the ground to ensure that the mud surface in the hole is more than 1m above the groundwater level.

Draw the line in advance at the exact location where the drill hole is needed, and install the drill bits with the same diameter and size of the drill hole. Connect the water pipe to the machine, the size of the water is appropriate and then turn on the machine, generally the hole is with the arm top, slowly advance it, the service life of the drill bit depends on the quality and what object you drill, generally if the concrete is about 20 eyes, if you encounter too many steel bars, it will be 10 eyes.

If you have any questions about this answer.

Summary. How to calculate the hole position?

Hello dear, the three drill bits are placed on the far left 320 one, 64 one, and the right 192 one. The left ruler is 320 + 44 = 364, and the right ruler is 192 + 44 = 236. Note that all three holes are spaced together.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

How to calculate the hole position?

How to calculate the hole position? Hello dear, the three drill bits are placed on the far left 320 one, 64 one Lu Jia, and the right 192 one on the line. The left ruler is 320 + 44 = 364, and the right ruler is 192 + 44 = 236.

Note that all three holes are spaced at the same distance, I hope it can help you. If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your efforts are very important to me, and your support is also the driving force for my progress. Finally, I wish you good health and a good mood!

4 rows of drilled rows of holes.

Hello dear, international standards. Between each drill bit is 32mm. To use an analogy:

I want to drill a 58mm hole, put the drill bit on 32mm, and then 32+58=90mm and then adjust the ruler to 90mm. And it came out. And so on ...

The hole spacing of the row of drills is 32mm, as long as the hole position is confirmed according to the drawing, how to calculate the hole position each time, it may be different, because there are too many custom furniture now, so it is necessary to accumulate the size and data of the hole spacing of the calculation fiber. Hope it helps.

Hello dear, I'm very sorry, we can't receive or send ** voice here, please describe it in text in detail, so as to better help you answer.

3 rows of drilling rows of holes what to calculate.

3 rows of drilling, what to calculate Hello dear, three drill bits are divided into buckets, don't put them on the far left 320 a, 64 a, and 192 on the right on the empty core. The left side is 320 + 44 = 364, and the right side is 192 + 44 = 236, I hope it can help you.