How should you tile a wall that has already been putty painted?

There are two issues that need to be paid attention to when pasting ceramic tiles and wall tiles, one is to explain what we should do with putty on the wall. Because as we all know, putty is divided into two types, one is ordinary putty, and the other is water-resistant putty. After ordinary putty encounters water, it will directly fail and fall off.

The water-resistant putty fails very slowly after encountering water, and has a certain water-resistant effect, but it will fall off after a long time.

After the putty layer is scraped, we can use waterproof paint to paint another layer on the putty, and then paste the brick after the waterproof paint is dry, the putty in the bedroom and living room can not be waterproof, but the putty in the toilet and kitchen is still waterproof when tiling. The stuffy head is treated to make the surface rougher, increase the adhesion of the mortar, and also cause the tile to fall. Because in this way, if you want to stick the tile on it, you must shovel off the putty, and the cleaning ability of the tile after burning ensures that the subsequent paving will not fall off in use, and the effect will be better if you apply the cement or interface agent again before paving.

If our tiles have been stuffy, be sure to clean up all the stuffy areas before applying them again. Remember, it's clean. There is no residue.

Ordinary putty is very simple, can be washed off, and is easy to shovel clean and then clean. Water-resistant putty is more troublesome, and it is necessary to use a special grinder to polish it off. Therefore, I also advise you here, if there is putty on the wall, we want to paste tiles on the wall, then we must completely shovel the original putty, and resolutely do not allow it to come up and directly paste tiles on the putty, so that the tiles will have problems sooner or later.

The above is a detailed interpretation of the problem, I hope it will help you, if you have any questions, you can leave me a message in the comment area, you can comment with me, if there is something wrong, you can also interact with me more, if you like the author, you can also follow me, your like is the biggest help to me, thank you.

First determine the location of the tiles, then polish the putty off the area, and then follow the normal process to apply the tiles.

In this case, the putty should be sanded first, and then the tile glue should be pasted on the wall, which is relatively firm.

Try to stick it with your hands. Keep it at a right angle when pasting. In this way, it can be closely integrated with putty.

Remove the putty layer. The place where the tile needs to be pasted should be easy to brush the putty layer with water and then remove it with a dust knife. After removing the putty layer, try to clean the wall as much as possible, and then roll the primer on the wall so that you can stick the wall tiles.

If you don't do the above, your wall tiles will not be firm after they are pasted. Scrape off the latex paint, and if you plan to apply the tile with a thin sticker, you need to check whether these two points meet the requirements. If it does not meet the requirements, the wall needs to be treated accordingly, and the tiles can be applied only after meeting the requirements.

With the continuous improvement of living standards, people have a new pursuit of home decoration. It turns out that the putty on the wall was refurbished for various reasons. The walls are tiled and look stylish and beautiful.

When the walls are dirty, it is clean with a damp towel. Especially the process of shoveling putty is more troublesome. Some people say it's easier to shovel walls with water, and that's right!

But it's just that it's not easy to shovel the older putty walls, as well as those that have just been scraped and want to change the tile decoration. Therefore, the wall is plastered with putty first, and tiles are pasted behind.

The landlord said that there was no way to change it, so he could only change it. As we all know, tiles are generally pasted on cement walls, so how can tiles be pasted on walls that have been brushed with putty? The original wall was shoveled by hand, and if the tempered paint was sprayed with water and the wall was soaked, a shovel was used.

In fact, the shovel is quite fast, so be sure to shovel it clean. But that doesn't mean it's okay to just lay tiles on the wall. Special treatment must be done to make the wall tiles fully meet the requirements of paving before they can be laid, so that the tiles laid on the wall can ensure the quality.

Generally speaking, on the wall surface of the original putty, it is necessary to remove the putty at the bottom layer, that is, to clean the original plastering layer.

We should prepare cement, and we should make the walls, and we can also live the cement, and then we should put tiles, the method is very simple, and it is also very good.

In fact, we can apply a layer of cement glue on the wall with putty, and then paste the tiles, which will be very good and very convenient.

Brush a layer of cement glue on the putty wall, so that it will be more convenient to paste the tiles again, and it will also be very firm.

The wall should have a certain strength, and it should also be particularly flat, so that it can be tiled, and the effect will be particularly good.

The wall that has been painted with putty should be swept clean before tiling. The putty layer should be scraped before the bricking construction, and if the putty has been scraped before the bricking construction, then it needs to be removed, otherwise it will bury a lot of hidden dangers for the later tiling. After the putty layer is scraped, we can apply another layer of waterproof paint on the wall, and then paste the wall tiles after the waterproof paint is dry.

The walls of the bedroom and living room can be left unwaterproofed, but the walls of the bathroom and kitchen should be tiled.

1.Tiles need to be laid before laying, which is the so-called pre-laying, mainly to calculate the amount of tiles laid to see the laying effect. Once the relevant highly elastic lines are marked, they are ready to be pasted.

Many tiles have to be soaked in water before pasting, and they can only be taken out to dry after no bubbles come out. That's about two hours. The key to tiling is the adhesive material, that is, cement mortar, which must be proportionally proportioned when blending, requiring uniformity and no bubbles.

2.We need to clean the base layer before plastering the wall, and then we need to clean all the things such as lime latex paint, wallpaper and other things on the wall, because tiles need sand and concrete. If putty is used, it will affect its adhesion to walls and wall tiles.

Over time, the tiles may fall off and crack, so be sure to remove the particles on the wall before applying tiles. When applying tiles, check whether the tiles are qualified. If there are cracks in the wall, in this case, the cracks should be announced before tiling.

If the cracks are not repaired, directly applying the tiles is also a kind of damage to the tiles.

3.If we have putty on our walls, we have to remove all the putty before pasting the wall tiles. Remember, this is to be cleaned up, and there should be no residue.

Ordinary putty is very simple, it can be shoveled off after washing, and it is easy to shovel off, and then it is also easy to clean up. Water-resistant putty is more troublesome and has to be sanded off with a special polishing machine. The above is the answer to the question of how to tile the wall that has been painted with putty.

You can sprinkle some water on the ground, so that you can put the tiles well, and it will make the tiles look very neat and beautiful, you can choose gray tiles, you can also choose some black tiles.

When pasting tiles, you need to scrub the dust on the wall with a rag first, and then paste the tiles along the corners in turn.

First remove the oil and dust, sprinkle water on the place where the tiles are glued, then scrape the putty off with a knife, clean the wall, and put some interface agent on the wall to paste the tiles.

If we plan to apply the tiles thinly, we need to check that these two points meet the requirements. If it does not meet the requirements, it is necessary to treat the wall accordingly, and the tile can only be pasted after the requirements are met. With the continuous improvement of living standards, people have a new pursuit of home decoration.

The original putty on the wall, for various reasons to redecorate, choose the wall to paste tiles, look fashionable and beautiful, the wall is dirty with a wet towel gently wiped very clean.

In particular, which process is more troublesome to shovel out putty. Some people say that it is easier to wet the wall with water, and that's right! But it's only for the older putty wall, and which ones have just been scraped and want to change the tile decoration is not what is easy to shovel?

That's why I put putty on the wall first, but then I want to put tiles on it. The landlord said that there was no way to change it, so we could only change it. As we all know, ceramic tiles are generally pasted on cement walls, so how to paste tiles on the walls that have been brushed with putty.

The original wall used to be made with a batch of scraping tempered coatings, there are batches of putty, manual shovels, if the tempered paint, the wall is sprinkled with water and soaked on the line, shovel it off with a shovel, in fact, the shovel is also very fast, must be shoveled clean. But it is not that you can just pave the tiles directly on the wall, you must do special treatment, so that the wall can fully meet the requirements of tile paving, and then you can pave the tiles, so that the tiles on the wall can ensure the quality.

Generally speaking, on the wall of the original putty, the putty needs to be removed to the bottom, that is, it is necessary to clean up to the original plastering layer that can be seen, if it is ordinary paint putty, it is easy to deal with, use a professional shovel knife to spray water on the original wall to humidify, you can simply dispose of it!

However, it will not take two or three years to repaint the putty and the same status quo will appear, and the wallpaper and wall cloth will only give the "emperor a new dress", and will not substantially solve the problem.

If you want to stick wall tiles, you must first polish the putty, otherwise the putty is too smooth and the tiles will fall off easily.

Tiles are only pasted up in the kitchen, bathroom, and laundry room. After I built it 10 years ago, I was helped by a friend who helped me find a real estate developer construction team to help me paste. I even want to paste on the putty layer wall, which is purely child's play, and it is purely a waste of tile money, cement mortar money, and pasting costs.

This method of water is not advisable, and there is a safety risk of falling off after pasting, so it must not be done in this way.

Because putty powder is only a wall decoration material, although it has a certain bond strength, it cannot be compared with concrete, and it will fall off after being wet, and its load capacity cannot withstand the weight of floor tiles! In recent years, more and more people will choose "floor tiles on the wall", laying tiles on the walls of the living room and dining room, abandoning the traditional latex paint, wallpaper and wall cloth.

Which construction method is stronger? This is related to many factors, such as the quality of the tile, the size of the gap in the tile paving, the soaking time of the tile, the construction technology and method of the tiling master, the mixing of cement mortar, the amount of cement, the various problems and construction methods of the tile are also very well understood. Which construction method is stronger?

The easiest way is to first roll the putty layer with varnish, and after drying, cover the walls with newspaper on the putty layer, and then paste the tiles with structural adhesive or other glue products on the newspaper. Anyone who tells you that you can keep the wall glue of their house is not pretending to know how to fool you into buying his glue. The surface of the putty itself that you can see will lose powder, and you can't guarantee the bottom layer.

Ecological Luyi replied: Putty can't stick to bricks, clean up the putty and chisel the wall. Before construction, the waterproof and moisture-proof wall should be done first, because the water absorption rate of the whole brick is usually more than 9%, but immediately after the waterproof construction, sprinkle a layer of fine sand, or sprinkle pure cement slurry after drying, and then paste the brick, in order to ensure the firmness of the wall tiles.

Yes, the wall can be shaved, then applied with cement mortar, and then tiled to make it very firm.

The adhesive of wall tiles is generally carried out on the plastering surface. Due to the fact that at this stage, the vast majority of regional wall tiles are all selected thin paste methods. That is, use the commonly used tile adhesive, scrape a thin layer on the wall, and then scrape a thin layer on the back of the floor tile.

After that, you can put the floor tiles and stick them directly to the wall.

The adhesive of wall tiles is generally carried out on the plastering surface. Due to the fact that at this stage, the vast majority of regional wall tiles are all selected thin paste methods. That is, use the commonly used tile adhesive, scrape a thin layer on the wall, and then scrape a thin layer on the back of the floor tile.

After that, you can put the floor tiles and stick them directly to the wall. If the tempered paint, the wall is sprinkled with water and wet, and it is shoveled with a batch of knives, and it is actually shoveled out quickly.

Be sure to shovel it clean. Otherwise, the shovel is not clean, the lower half of the tile is pasted, the putty powder of the interior wall that cannot be shoveled will be powdered, and the mixed mortar can not be efficiently integrated with the wall, which may cause the wall to crack. After shoveling through the wall, the wall will drop powder and sand, be sure to brush the wall solid, until the wall can not sand off the powder, the wall is not detailed here, it mainly has the effect of waterproof putty.

In order to better make the wall tiles more solid, after the wall is solidified, a layer of brushing agent can also be brushed.

It is not easy to go wrong with the tiles in the back, provided that the professional skills of the tiling master are better. It turns out that the putty powder on the inner wall on the wall has added concrete to it, so it is more laborious, and it is so laborious that you begin to doubt life, impact drills, electric scripts, knocking, beating, grinding, and all the expatriates sometimes can't eliminate how much money it costs! In order to better stick the expected goal of the quality of wall tiles,You'll have to keep going to the bottom!

If it is a large area, it is recommended to ask someone to deal with it, the effect is better!