How do I fix the washing machine at home when it suddenly doesn t work?

The loosening of the belt of the washing machine will also lead to the reason why the washing machine does not rotate, and the loosening of the belt will slow down the speed of the wave wheel, or even not rotate in serious cases. Solution: First of all, loosen the motor screws and move the motor outward to make the belt tight, but the belt should not be too tight, too tight will increase the friction between the belt and the pulley, and affect the use time of the motor.

If the water inlet solenoid valve sounds, then it may be that the water level sensor is faulty or the water level pipe is leaking, resulting in water ingress all the time, because the computer board does not read the signal that the water level has been reached, so it has been supplying power to the water inlet solenoid valve. Precautions for the use of washing machine, do not put a lot of clothes at a time, the washing machine has a certain amount of clothing carrying capacity, if there are too many clothes, it will make the motor too heavy, which may cause the motor to stop rotating. It is recommended that you should first take the air outside to dry, and wait until the smell of some oil stains has dispersed, and then put it in the washing machine to wash again.

The above content refers to Encyclopedia-**Common faults of washing machines.

Check whether there is any problem with the wiring of the washing machine and the power supply at home, if it is powered on, there should be a power indicator light on the washing machine. If the power is normal and the washing machine does not turn, you have to contact the after-sales service personnel for maintenance.

If the washing machine suddenly does not run, there will be many reasons, such as the previous washing machine belt is loose and will suddenly stop running.

If it's not a power outage, let a professional fix it.

How to deal with the washing machine at home suddenly does not turn, my washing machine is often lazy, sometimes it does not turn, and it is a problem with the washing machine capacity that I checked on the Internet.

The washing machine at home suddenly stopped working and can be repaired as follows:

The washing machine dehydration bucket version does not turn: according to the single dehydration test, the complete wave wheel wheel wheel rotation mechanical right total bearing dehydration spring is broken, the washing machine is put down, the bottom plate belt is loosely unscrewed off the belt pulley, the screw is removed from the wheel and then the rubber gear dial can be seen. Take the accessories store to buy 2 3 yuan to put butter on the waiting note, a single dehydration wave wheel dehydration bucket, all turn to check the motor to start the capacitor to hit the washing machine cover, capacitive washing machine board, the left side of the capacitor 12uf or 14uf 2 lines to the accessories store to buy **20 yuan or so.

The washing machine turbine does not rotate the first wave, the motor belt, whether it falls off, the motor should turn the washing machine capacitor, the capacity is enough washing machine motor, it belongs to the capacitive start motor capacitor, the role is to improve the motor end voltage capacitor capacity enough motor end voltage to reduce the motor can start running. It is recommended that the washing machine sales service department contact for repair and replacement.

The drum washing machine does not turn for maintenance: the drum belt can be driven, the belt is broken, the belt is replaced, it is expensive to dozens, the motor is directly driven, it depends on the motor is broken, and the computer board problem is estimated to be hundreds.

1. When the washing machine comes to wash clothes, if the motor has its own buzzing sound, bai but does not turn, it may be a problem to start the DU capacitor. If the motor does not make a little noise, it may be that the lid linkage switch of the dehydration bucket is faulty.

2 Check whether the belt is loose, check the pawl and clutch, and see if the brake is tight or the mechanism plate on the drum cover is broken.

3 How to solve the problem that the automatic washing machine does not turn, hum and does not rotate, some have a clutch, the motor is very hot, the starting capacitor may be broken, or the wire head is off, causing the motor to not start, if there is no clutch, see if the motor is stuck, do not idle the belt first, whether the motor is stuck, whether it is stuck, if it is not stuck, most of the starting capacitors are problematic.

4. The spinning tube does not rotate, generally in the following situations: the motor is burned out (there is no reflection when the power is on), the starting capacitor is damaged (the motor cannot be started after the power is on), the brake line is broken (the motor cannot be started after the power is turned on), the timer is damaged (after twisting and twisting, the timer has no ticking sound), the water seal is damaged (the water seal is damaged, the clothes are difficult to put on the right until the official does not turn, at this time, the sound of the clothes tube can be heard), and the line is open (generally visible with the eye).

First, it is recommended to contact a professional repairer.

Second, there are many reasons for not running bai, and if you can't find the reason for du, you can't repair it. To find the cause, you also need some DAO tools and materials. These families are more difficult to have.

Three, possible reasons for not working:

1. Poor contact with external power supply.

2. The components of the control module are aging and damaged, and the running module is not started.

3. Vibration causes the internal circuit to loosen and short circuit.

4. The motor is damaged and the transmission parts are loose.

The range of possible causes is wide.

Specifically, you can say the next washing bai

What is the model of the clothing machine? zhi

The washing machine suddenly could not dao

Under normal circumstances, the contact contact of components such as timers, program controllers and selector switches on the washing machine can be considered for poor contact, which will cause sudden failure to work, in addition, the mechanical system causes of the failure are:

1) The V-belt falls off.

2) The wave wheel is entangled in clothing.

3) The power supply voltage is unstable.

4. Wave wheel axle holding shaft.

5) The motor is burned out.

6) The fastening screws on the pulley are loose.

1. Plug in the power cord socket to ensure that the line is unblockedThe power cord plug is not in good contact with the socket, and after twisting the washing timer knob and the dehydration timer knob, both sides do not work:Processing:

It may be that the power cord plug is not in good contact with the socket, and the line is not working. Plug in the power cord socket to ensure that the line is unblocked.

2. Screw the knob of the washing and drain selection switch to the standard or gentle positionWhen the knob of the washing and drain selection switch is in the drain position, the wave wheel does not rotate after turning the washing timer. This is determined when the washing machine is designed, in order to prevent damage to the laundry that is not taken out of the laundry bucket when the wave wheel rotates after drainage.

Precautions for the use of washing machines.

The drying capacity of the washer-dryer is half of the washing capacity, so you should pay attention not to place too much laundry when drying to avoid wrinkles after drying.

During the dehydration procedure, the lid must be closed, and the lid should not be opened frequently, and the washing and dewatering bucket should never be touched by hand to avoid getting your hands involved and causing danger.

Never wash or dehydrate clothes containing volatile substances (solvents, alcohol, etc.) to avoid accidents, in the dehydration imbalance of the computerized automatic washing machine can be dehydrated imbalance correction, if the correction of 2 times has not solved the imbalance problem, will stop and alarm, at this time, should open the cover, put the clothes on the side evenly, and then close the cover, press the start pause button.

The above content refers to Encyclopedia-**Common faults of washing machines.

1. The failure of the computer control panel causes the washing machine to not rotate, and it is recommended to replace it, because the control panel is covered with glue in order to be waterproof, which is quite inconvenient to repair.

2. If the motor does not rotate with a humming sound after the power is turned on, it may be that the motor is short-circuited or damaged, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted. If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

3. The washing machine cannot be rotated due to the damage of the solenoid valve, because the washing and dewatering of the automatic washing machine is completed by the gear at the bottom of the conversion of the solenoid valve, if the solenoid valve is damaged, the washing machine can not enter the dehydration program, it is recommended to replace the solenoid valve.

4. Check the power supply or power plug, because the connecting wires of the drum washing machine are all connected with connectors, so during transportation, due to vibration and other reasons, the motor plug is often loosened or the plug is ejected during installation, if the plug is loose, it can be re-fixed to prevent it from falling off again.

1. Check why the washing machine cannot work properly, if the washing machine does not rotate because the motor is damaged, we have to cut off the power supply, open the cover plate behind the washing machine, try to move the belt of the washing machine by hand, and check that the belt is not stuck. If the belt is not stuck, but the motor still does not rotate and there is an abnormal sound, see if there is a short circuit. At this time, the power supply should be disconnected, the belt should be removed, and the machine should be restarted.

If the machine still does not rotate, it should be repaired or replaced with a new motor.

2. The wash-off function of the washing machine is realized by the solenoid valve driving the gear at the bottom, the solenoid valve is damaged, the washing machine does not rotate, it is recommended to replace the solenoid valve. 3. The operation of the washing machine needs to be connected to the wire, and the washing machine does not turn to check whether the plug is loose, and plug the plug back in to prevent the plug from falling off again.

4. Check whether the computer control panel has water ingress, if the computer control board has fog and the washing machine does not turn, it is recommended to find a professional maintenance personnel to repair it. 5. Check if there are too many clothes, turn off the power and take out some clothes. Start the washing machine again.

6. Look at the gap around the washing machine and the laundry bucket to see if there are any clothes or other sundries stuck in it, resulting in the washing machine not working normally. At this time, you need to find a slender object and pick out the debris in the gap. In the process of daily use, clean the washing machine in time to avoid unnecessary trouble caused by debris blockage.

If the washing machine does not turn, it is best not to repair it yourself, because if you repair it yourself, you may use your own damage to make the repair more difficult, and it is also possible that the maintenance personnel will come to the door, saying that it is caused by your own maintenance, and you will not bear the cost of this door-to-door and bear the cost of maintenance.

If the washing machine does not turn and repair it by yourself, you need to read the specific instructions and understand its internal structure in order to repair it better. If you are not familiar with it, it is best to find a professional master to repair it, and it is easy to break it by blindly disassembling it to repair.

1.Use a screwdriver to remove the set screw in the middle of the wave wheel.

2.Use wire bending to make two small hooks or use two flat-edged screwdrivers.

3.Insert symmetrically into the gap around the perimeter of the roller, gently pull up or pry, and change the direction of symmetry.

4.Slow vertical and slow force, the wave wheel will slowly move up from the wave wheel axis, and the Yu Hong wave wheel will be taken out. Pay attention to Huipei not to exert too much force at once, but to use even force and change the direction.

1.Use a screwdriver to remove the set screw in the middle of the wave wheel. 2.

Use wire bending to make two small hooks or use two flat-edged screwdrivers. 3.Symmetrically insert into the gap around the dust seepage blind wave wheel, gently pull up or pry, and change the symmetrical direction.

4.Slowly exert force, and the wave wheel will slowly move up from the wave wheel shaft, and the wave wheel will be taken out. Be careful not to exert too much force at once, and use the shouting force and changing the air direction evenly.

5.If the wave wheel and the wave wheel shaft are glued, the heat can be blown by a hair dryer, and the glue will be softened.

The washing machine at home suddenly fails to operate, in the case of ensuring that the power supply of the socket is normal, check as follows:

1. Check whether the fuse on the circuit board of the washing machine is broken.

2. Check whether the tap water is stopped, and the washing machine cannot run if there is not enough water.

3. Open the back cover of the washing machine, smell whether there is a burnt smell, if there is, the motor is burned out, contact the after-sales maintenance.

4. In the middle of washing, if you open the washing machine door, the washing machine door is not closed.

5. There is no problem with the above, only contact after-sales.

There are two reasons why the washing machine suddenly cannot be stopped during the washing process:

1. If the indicator light is not on, it is a power outage, mainly check whether the socket has electricity, no electricity, check whether the indoor air is tripped;

2. If the indicator light is on, but any button does not work, the computer board is broken, and you can replace it with a computer board.

The washing machine suddenly does not run, first of all, to see whether the power supply is out of power, it is best to contact the after-sales service of what brand of washing machine you use.

First check the power supply and mode, then check the water level sensor, fuse, and traction motor.

How do I fix the washing machine at home when it suddenly doesn't work?

Hello, I'm glad to serve you1. Check if the fuse on the circuit board of the washing machine is broken. 2. Check whether the tap water is stopped, and the washing machine cannot run if there is not enough water. 3. Open the back cover of the washing machine, smell whether there is a burnt smell, if there is, it is that the electric Huimu machine is burned out, contact the after-sales closed limb maintenance.

4. In the middle of washing, if you open the washing machine door, the washing machine door is not closed. 5. There is no problem with the above, only contact after-sales.

1. The washing machine is not washed from water inlet to overflow

Check whether the water level switch is connected to the void and whether the connecting pipe of the water level switch is perforated. Check if the capacitor fails, if the belt falls off and breaks because it is too loose or too tight, if the clutch is stuck, or if the clutch is turning but the wave wheel is not working. Find the reason to replace the relevant parts, if there is no problem, check whether the motor is powered, if not, even check whether the wiring falls off or the circuit board is short-circuited.

2. The washing machine is buzzing and not washing

Replace the starting capacitor of the vertical non-combustion motor, rewind the coil winding of the motor or replace it with a new motor. When the washing machine makes a humming noise, regardless of the above reasons, the power supply to the washing machine must be cut off immediately. If it is the humming sound of the motor, then it is caused by the decrease in capacitance value, and you can change the capacitor.