The washing machine does not turn, where is it broken, how to fix it

It could be a motor failure. Try opening the back cover of the washing machine and moving the pulley by hand if it doesn't get stuck. When the power is turned on and the motor hums, but does not rotate, it means that the motor is short-circuited or damaged, or the motor circuit is not connected to the capacitor.

At this point, cut off the power supply, remove the motor belt, and restart. Other reasons: the brakes on the bottom of the spin dry barrel did not release.

Remove the back cover, open the door cover of the dehydration bucket, and check that the grip brake is loose. If not, check to see if the cable attached to the door cover is loose or broken. In the above case, simply tighten or connect the cable so that the brake can be released when the door cover is opened.

The bucket was leaking. Check the washing machine bucket for water leaks. If there is a water leak, the seal can be replaced.

If there is water leakage, a waterproof cover can be installed on the motor to prevent water leakage from flowing into the motor and damaging the motor.

The reasons why the washing machine does not turn and how to repair it are as follows:

1. The internal damage of the computer board.

The power supply of the washing machine motor is passed through the thyristor by the computer board.

Control the output, if the thyristor or related circuits in the computer board fail, the motor will not rotate naturally without a power supply, and the judgment method is to use a multimeter directly.

Measure whether the computer board has a motor output voltage.

If the computer board is working normally and there is no alarm, but there is no motor voltage output, it means that the computer board is damaged internally, and it can be repaired by replacing the computer board of the same model.

2. The water level sensor is broken.

The function of the water level sensor is to control the water level of the washing machine, under normal circumstances, when the water in the washing machine reaches the set water level, the water pressure in the bucket acts on the inside of the water level sensor through the connected soft rubber hose. The sensor feeds back to the computer board based on the perceived water pressure to control whether the water enters or not.

If the sensor is damaged or the soft hose connected to the sensor is damaged, leaking, and the computer board is not getting the correct feedback signal, there will be multiple water ingress or computer board alarms. When there is no voltage sent to the motor, the computer board will not turn, if there is too much water in the washing machine or the water in the washing machine alarms for a while, we can fix the fault by replacing the soft hose or water level sensor.

3. The motor is burned out.

An open circuit in the internal coil of the motor.

or a short circuit will cause the motor not to rotate. We use a multimeter to measure the power supply of the motor. If the 220V voltage is normal and the starting capacitor is intact, you can be sure that the motor is damaged and can be repaired after replacement.

4. Line problems.

If the motor drive voltage output from the computer board is normal, and there is no input voltage on the motor side, the circuit between the computer board and the motor is disconnected. It is easy to find by disassembling the case and inspecting the circuitry.

5. The capacitor is damaged.

The most common problem in washing machine repair is that the starter capacitor is damaged and the motor cannot turn. If the washing machine is flooded normally, and the motor does not rotate but there is a humming sound, it is actually a faulty starting capacitor capacity, which causes the motor to start the winding power to be insufficient and unable to start the motor, so it will make a humming sound. It can be repaired by replacing the capacitor of the same model.

1. Plug in the power cord socket to ensure that the line is unblockedThe power cord plug is not in good contact with the socket, and after twisting the washing timer knob and the dehydration timer knob, both sides do not work:Processing:

It may be that the power cord plug is not in good contact with the socket, and the line is not working. Plug in the power cord socket to ensure that the line is unblocked.

2. Screw the knob of the washing and drain selection switch to the standard or gentle positionWhen the knob of the washing and drain selection switch is in the drain position, the wave wheel does not rotate after turning the washing timer. This is determined when the washing machine is designed, in order to prevent damage to the laundry that is not taken out of the laundry bucket when the wave wheel rotates after drainage.

Precautions for the use of washing machines.

The drying capacity of the washer-dryer is half of the washing capacity, so you should pay attention not to place too much laundry when drying to avoid wrinkles after drying.

During the dehydration procedure, the lid must be closed, and the lid should not be opened frequently, and the washing and dewatering bucket should never be touched by hand to avoid getting your hands involved and causing danger.

Never wash or dehydrate clothes containing volatile substances (solvents, alcohol, etc.) to avoid accidents, in the dehydration imbalance of the computerized automatic washing machine can be dehydrated imbalance correction, if the correction of 2 times has not solved the imbalance problem, will stop and alarm, at this time, should open the cover, put the clothes on the side evenly, and then close the cover, press the start pause button.

The above content refers to Encyclopedia-**Common faults of washing machines.

1. The failure of the computer control panel causes the washing machine to not rotate, and it is recommended to replace it, because the control panel is covered with glue in order to be waterproof, which is quite inconvenient to repair.

2. If the motor does not rotate with a humming sound after the power is turned on, it may be that the motor is short-circuited or damaged, or the capacitor is not connected to the motor circuit. At this time, the power supply should be cut off, and the motor belt should be removed and restarted. If the motor still does not rotate or the speed is low, it is a motor failure and the motor should be repaired or replaced.

3. The washing machine cannot be rotated due to the damage of the solenoid valve, because the washing and dewatering of the automatic washing machine is completed by the gear at the bottom of the conversion of the solenoid valve, if the solenoid valve is damaged, the washing machine can not enter the dehydration program, it is recommended to replace the solenoid valve.

4. Check the power supply or power plug, because the connecting wires of the drum washing machine are all connected with connectors, so during transportation, due to vibration and other reasons, the motor plug is often loosened or the plug is ejected during installation, if the plug is loose, it can be re-fixed to prevent it from falling off again.

1. Check why the washing machine cannot work properly, if the washing machine does not rotate because the motor is damaged, we have to cut off the power supply, open the cover plate behind the washing machine, try to move the belt of the washing machine by hand, and check that the belt is not stuck. If the belt is not stuck, but the motor still does not rotate and there is an abnormal sound, see if there is a short circuit. At this time, the power supply should be disconnected, the belt should be removed, and the machine should be restarted.

If the machine still does not rotate, it should be repaired or replaced with a new motor.

2. The wash-off function of the washing machine is realized by the solenoid valve driving the gear at the bottom, the solenoid valve is damaged, the washing machine does not rotate, it is recommended to replace the solenoid valve. 3. The operation of the washing machine needs to be connected to the wire, and the washing machine does not turn to check whether the plug is loose, and plug the plug back in to prevent the plug from falling off again.

4. Check whether the computer control panel has water ingress, if the computer control board has fog and the washing machine does not turn, it is recommended to find a professional maintenance personnel to repair it. 5. Check if there are too many clothes, turn off the power and take out some clothes. Start the washing machine again.

6. Look at the gap around the washing machine and the laundry bucket to see if there are any clothes or other sundries stuck in it, resulting in the washing machine not working normally. At this time, you need to find a slender object and pick out the debris in the gap. In the process of daily use, clean the washing machine in time to avoid unnecessary trouble caused by debris blockage.

If the washing machine does not turn, it is best not to repair it yourself, because if you repair it yourself, you may use your own damage to make the repair more difficult, and it is also possible that the maintenance personnel will come to the door, saying that it is caused by your own maintenance, and you will not bear the cost of this door-to-door and bear the cost of maintenance.

If the washing machine does not turn and repair it by yourself, you need to read the specific instructions and understand its internal structure in order to repair it better. If you are not familiar with it, it is best to find a professional master to repair it, and it is easy to break it by blindly disassembling it to repair.

First check whether the power is connected and whether there is a power outage; In addition, the inspection considers that the motor is aging, resulting in the inability to rotate; Then in turn, Nataja inspects the wave wheel, motor belt, washing machine program and other parts, and after detecting the problem, replace the corresponding components or let professional maintenance personnel repair them.

Solution: 1. Check the power supply: If the washing machine does not turn, check whether the power is connected and whether the power is off, and ensure that the power supply is on.

2. Motor failure: according to the use time of the washing machine, detect whether the washing machine has been used for too long and there is a click failure, if the motor of the same model can be replaced.

3. Wave wheel failure: see if the screw of the lower wave wheel is loose, and tighten it loosely; Check whether the buckle of the wave wheel is broken, if it is broken, it will not be able to follow the operation of the motor, and the buckle can be replaced at this time.

4. Belt problem: the belt is excessively worn, becomes longer and smoother, resulting in loosening and no lifting collapse method to pull the hole early, and the new belt can be replaced at this time.

5. Washing machine program failure: The fault mainly refers to the system failure of the computer board, and the program cannot be started.

Note: During the warranty period, it is best not to disassemble the machine for inspection by yourself, because this will affect the after-sales service of the washing machine.

Hello, 1 3 step by step reading Reasons and solutions for washing machine drums not turning: First, when the washing machine is washing clothes, if the motor has a humming sound, but does not turn, it may be a problem with starting the motor container. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

Second, check whether the belt is loose, check the pawl and clutch, and see if the brake is tight or whether the mechanism plate on the drum cover is broken. 2 3 Third, the automatic washing machine does not rotate, some motors with clutches are very hot, and the starting capacitor may be broken, or the wire head falls off and the motor cannot be started. If you don't have a clutch, see if the motor is stuck, don't dismantle the belt quietly under the idling motor experiment, whether it is stuck, if it is not stuck, most of the starting capacitors are problematic.

3 3 Fourth, the spinning drum does not rotate in the following situations: 1. The motor is burned out (there is no reflection of the bul when the power is on). 2. The brake line is broken (the motor cannot be started after the power is turned on).

3. The timer is damaged (after twisting and twisting, the timer has no ticking sound and is old). 4. The water seal is damaged (the water seal is damaged, and it is difficult to put the clothes right until the official does not turn, and the sound of the clothes tube can be heard at this time). 5. The line is open (generally visible with the eye).