How to fix a broken zipper on clothes, and how to fix a broken zipper on a broken clothes

Updated on society 2024-07-13
6 answers
  1. Anonymous users2024-02-12

    Zippers are always indispensable in our daily life, not only our pants, coats, quilt covers and these dolls, the zipper on it is broken, because a small zipper throws away all these broken things, it is inevitable that there will be a little waste, so today I will share with you several very common ways to repair zippers.

    Preparation materials: old clothes, zipper pulls, pliers.

    Needle, thread. Clothes zippers are always broken, don't even throw away clothes, today I will teach you 3 ways to repair zipper pulls.

    One: Dress jacket zipper puller.

    If the zipper puller is broken, we don't need to throw away the whole piece of clothing, just a simple action, pull our zipper puller to the top, you look at the position of the teeth of our zipper pull, there will be an oblique angle here, it is designed to facilitate us to replace the zipper pull.

    Skim the zipper puller directly at this bevel angle and easily approach our zipper puller.

    Then we found an old garment from home and took the zipper off it in the same way.

    The old zipper that we removed was facing the top of our teeth, and there was a small tooth mark on it, and we put it on.

    Let's try it out after we put it on, and it won't matter if we zip it up, so we can easily save a piece of clothing.

    Two: pants zipper.

    The second is the zipper of our pants, if this side is broken, our pants should not be thrown away in their entirety. In fact, at the very bottom of the chain teeth of our pants, we cut a small opening with scissors.

    After cutting it, we pulled our zipper puller straight down and threaded it through this notch.

    We pull it and look at it, and if we find that it can't pull it, we give it an exit.

    Here we need to use a vice at home.

    Put our zipper pull, simply clip it, let's talk about it briefly, and try again.

    So that everyone can see that he has repaired it, and finally we take out the needle and thread and sew it up about a centimeter above the notch we have cut it, so that we don't pull the zipper pull.

    Three: **Zipper.

    The third is the zipper, which is also the most headache and the most common problem, in this case, the whole bed is too wasteful to throw away, pull our zipper head to the end, and then cut out a small gap for the battery on both sides.

    Then take off the zipper puller, we find a zipper puller of the same size, directly put both sides on both sides, and attach it on.

    So we can fix it as soon as we have a bed**.

    We also sew it up with a needle to prevent the zipper puller from slipping.

  2. Anonymous users2024-02-11

    If the zipper of the clothes is broken, see if the zipper is not easy to use, change the zipper or take the zipper to the tailor shop and replace it with a new one.

  3. Anonymous users2024-02-10

    How to fix a broken zipper of clothes, how to repair a zipper of a garment, no need to spend money to repair a broken zipper of a trot, a broken zipper of a dress can be easily repaired with a knife, a way to repair a zipper of a trot, no need to spend money to repair a broken zipper of a garment, the easiest and most convenient way to repair a zipper of a garment.

  4. Anonymous users2024-02-09

    If the zipper of the clothes is broken, you can replace it in the following ways.

    Use a straw to change the zipper:

    Cut one end of the straw about 1 cm long, then cut the cut part from the middle, fold it in half, and press it into a zipper pull.

    Glue the finished zipper puller to the damaged zipper with double-sided glue, then press it with pliers, and finally trim the excess corners to repair the damaged zipper. You can easily repair the zipper with a straw, which is really simple and practical, and you don't have to worry about it if the zipper is broken in the future.

    How to replace the zipper pull:

    If the zipper puller is broken, we don't need to throw away the whole piece of clothing, just a simple action, pull our zipper puller to the top, you look at the position of the teeth of our zipper pull, there will be an oblique angle here, it is designed to facilitate us to replace the zipper pull.

    Skimming the zipper puller directly to the hole and burning the angle, we easily approached our zipper puller, and then we found an old dress from home and took the zipper off it in the same way. The old zipper we removed was closed at the top of our chain teeth, there was a small tooth mark here, we put it on, and after we installed it, we tried it, and our zipper would not affect it at all, so that we could easily save a piece of clothing. <>

  5. Anonymous users2024-02-08

    Tips for repairing broken zippers on clothes:

    1. After the zipper is closed, it is always easy to open or it is difficult to pull.

    This problem is easy to solve, just use soap to apply back and forth on both sides of the zipper to make the zipper smoother. After application, strengthen the zipper and pull back and forth a few more times. So that the zipper is repaired, and it's very simple.

    In addition to using soap, if you have candles at home, you can also fix the zipper.

    2. The zipper can't be closed.

    The surface of the zipper does not seem to have any problems, but after the zipper is closed, the two chains are separated because the upper and lower parts of the zipper are stretched apart from each other or left and right. You can use pliers up and down or left and right to gently clamp a clamp, it should be noted that it must be very light, and then test it, if you can pull it on, if you can't pull it up, then gently clamp it twice, until it is repaired.

    3. The zipper head is broken or damaged and cannot be used.

    At this time, don't replace the entire zipper, just replace the zipper pull. Removing the zipper puller is very simple, there is a groove at the top of the zipper, and you can simply remove the zipper puller from the card slot by pulling it out in an oblique direction.

    Zipper maintenance tips:

    1. When using it at ordinary times, it is necessary to pay attention to whether there are "broken belly", "tooth loss", crooked and other problems on the zipper. If the zipper is loose and the teeth are missing, you can use a small hammer to gently knock a few times on the zipper head to make the upper and lower chain teeth bite tighter, and the teeth will not be removed again.

    2. The zipper of aluminum alloy is more susceptible to corrosion, so it should be kept dry and not damp, so as to prevent the aluminum teeth from generating white oxides, which will cause the zipper to rust over time, affecting the use of the search, and at the same time, it should be noted that it is not in contact with alkaline and acidic substances. When preserving in the mu, it is necessary to ensure a certain degree of ventilation, do not seal and store, and do not store in a humid environment, and use moisture-proof paper or dehumidifier when necessary.

    3. When pulling the zipper, you should first align the teeth on both sides, and then pinch the zipper head and gently pull it forward along the track, without pulling hard, so as not to cause "crooked teeth", "broken belly" and "tooth loss". If the zipper is astringent and inflexible to pull, you can wipe it with a cloth first and then put a layer of white wax on the "teeth".

  6. Anonymous users2024-02-07

    1. Find a white wax, even a candle, or the yellow or white wax of the pill, and apply it to the teeth of the zipper.

    2. The oil of the sewing machine is relatively transparent and clean, and the crack can be dripped on the zipper, but don't do so much, otherwise it will stay. If you don't have sewing oil, you can make do with peanut oil and vegetable oil, and it is not recommended that the oil is dirty.

    3. When the zipper is not smooth, if there is someone at home who knows how to tinker, you can sew a wind and discipline buckle hook with a needle and thread at the part below the zipper, so that you can hook the square hole at the top of the zipper, so that the zipper activity is smoother, and it is also relatively firm, and it is not easy to derail.

    4. The zipper is not good, you can see if there is a problem with the head of the zipper, you can try to replace a good head, go to the outside clothing store, and change it on the street.

Related questions
14 answers2024-07-13

Repair cracked zippers you need tools and materials:

Needle-nose pliers, zipper pulls (if the zipper puller is too bad to bite the zipper on both sides, or if the zipper puller is plastic, then you may need a zipper puller of the same size, usually you can find one on other old clothing). >>>More

13 answers2024-07-13

1. First remove the old zipper, which can cut the needle and thread intermittently, and then slowly remove it. >>>More

7 answers2024-07-13

1. Pull the zipper to the head.

Pull the zipper to either end of the zipper so that all the teeth are exposed. Try to expose all the teeth so that the zipper can be pulled back smoothly. >>>More

30 answers2024-07-13

Have you ever been in this situation where the zipper of your clothes has been accidentally broken? >>>More

9 answers2024-07-13

First, if you put too many things in the bag, it will crack, or the teeth are too loose, so you should clamp the mouth of the zipper puller with a vice. >>>More