How to apply tiles to waterproofing paint? What are some things to look out for?

If you want to paste the tiles, you must choose a rigid waterproofing agent, because of its poor elasticity, and the fit of the wall will be higher, even if the tile will have a pulling force, it will not tear off the waterproof layer, which can effectively prevent the tile from falling off, and the flexible waterproofing agent, although the life is longer, but some deformation will occur in the drying process. Put some lime paste in the cement mortar, and when applied on the waterproof layer, it will create an uneven effect, which can make it unsmooth, thereby increasing friction, and you can also use tile adhesive for thin pasting, which can also directly play a fixed role.

It is not possible to directly paste tiles on the waterproof coating, and you need to make a protective layer on the waterproof coating first; To clean the bathroom wall first, you need to do brushing, and then make a protective layer on the waterproof coating to paste the tile, which can make the tile more firm.

You can lay cement mortar on top of the waterproof layer, and then make a surface layer or tile paste; Don't apply too much waterproof paint when applying it, so as not to make the wall too thick and dry, and fail to achieve the waterproof effect.

1. When is it waterproof? How?

1. Toilets, first of all, toilets. This is the point of waterproofing. The toilet should not only be waterproof on the ground, but also on the walls. The waterproofing of the wall of the shower area should be placed on the top, generally above the meter; The waterproofing of the wall in other areas of the bathroom is generally more than 30 cm.

2. Kitchen, followed by kitchen. The kitchen uses a lot of water, so it also needs to be waterproof. The floor of the kitchen is also required to be waterproof, followed by the wall, the wall is required to be waterproof at least 30 cm, and the waterproof area behind the vegetable sink is required to be more than 50 cm at the water outlet.

3. Balcony, and finally balcony. Whether to waterproof the balcony or not, first of all, depends on the function of the balcony. If it is an unenclosed balcony, it will accumulate water during the rainy season, so it should be waterproof.

Enclosed balconies depend on whether they are living balconies or leisure balconies. The general leisure balcony does not leak the ground, does not need water, and does not need to be waterproof. If there are water pipes buried in the living balcony and the floor leaks, it must be waterproofed.

Generally, the floor is fully waterproof, and more than 30 cm from the wall is waterproof. There is a washbasin and a washing machine on the general living balcony, and the waterproofing of this part of the wall must be about meters.

Second, after waterproof construction, why can't the tiles be sticked?

In fact, it is also a general phenomenon to paste tiles after the wall is waterproof, and the bricklayer master told me that as long as you find the right reason, it can be solved. As you know, when we apply tiles, we apply cement mortar on the back of the tiles. Moisture will solidify when it penetrates the wall, but it will become smooth enough with a waterproof layer.

At that time, moisture does not enter and becomes difficult to air dry. Therefore, it is not possible to fix the paste firmly when tiling.

3. After waterproof construction, are the tiles not firmly pasted?

The fact that the tiles are not firmly pasted is related to the fact that the waterproof layer does not penetrate into the water. Generally tiled. The back of the tile is coated with cement mortar.

Moisture would have soaked into the wall and dried out, but with a waterproofing layer, the wall will become smooth and water will not penetrate. If it is slow, it will be difficult to fix the wall tiles. How to solve this situation?

There are several such methods. 1. The waterproof coating should be used correctly in proportion, and the hair should be made on the surface during painting; Or wait for the waterproof to dry, use cement to "stretch the hair" of the wall, and then paste the bricks; 2. There are two main ways to paste ceramic tiles. It is made of cement mortar or brickwork.

When using cement mortar, the cement mortar should not be too thick, and there should be a gap between the bricks; If bricks are used, the viscosity is several times that of cement mortar, so I don't pay much attention to details. 3. Refuse the wall on the floor tile, some owners hope that they can decorate the personality beautifully, but the wall on the floor tile is popular again, I hope so. However, floor tiles are laid on the ground after all, so when they are laid on the wall, the size is too large, the mass is too large, and it is easy to fall off.

If the waterproof coating has been done on the wall, you can directly apply tiles on it, because the next step is to directly apply tiles to the waterproof coating.

No, it is necessary to make a layer of insulation or thermal insulation layer and fireproof layer to protect the waterproof coating, improve safety, improve the durability of the waterproof coating, and improve the functionality of the waterproof coating.

OK. After the waterproofing is done, the closed water test is done, and when the paint is dry, you can paste the tiles. First brush a layer of tile adhesive on the back of the tile, then brush cement and sand, and then brush a layer of adhesive on the wall or ground, and then paste the tile on the wall, which will increase the service life of the tile a lot, and it will not fall off or hollow.

1. After the wall is made of waterproof coating, we must not be able to directly paste the wall tiles on it, we need to make a protective layer of mortar waterproofing agent on the wall, and we can paste the tiles after the mortar protective layer is completely dry, and the quality of the tiles will be better and better, so that the water absorption rate of the tiles will be reduced, and it is difficult to meet our needs by using the sand cement pasted tiles to be paved.

2. And for the current waterproof coating base is mainly based on the concrete wall, we only need to do a good job of waterproofing before we can paste the tile, but now the market also has a waterproof coating that can be done directly on the tile, but in fact, this method is still unreliable, and there is basically no waterproof effect after the best.

1. If we choose cement mortar waterproof coating, we can actually directly paste tiles on it in this case, but generally in order to achieve better adhesion during our construction, we generally paint a layer of 108 construction glue on the wall and then pave the tiles.

2. When the tile is paved, we generally use cement mortar directly to paste the ceramic tile on the load-bearing wall, but for the flue or the sewer pipe of the red brick package, in order to avoid the situation that the tile falls off in the later stage, we had better draw the wall before the formal tiling, and then we paste the tiles, so as to increase its adhesion.

3. The main purpose of treating the waterproof surface is to prevent the tile from hollowing and falling off, so for the current construction method can also be like this, choose to use the tile paste for the tile paste, which is what we call the thin paste, because the viscosity of the tile paste is relatively large, it can better avoid quality problems, but in this way, the construction cost will increase a lot.

In fact, for the current decoration market, the technology is more reliable, many often appear problems, now in the construction, professional workers and masters will have a reasonable way to deal with it, so when we are constructing, we must find professional construction personnel, we can tell them our questions, so that they can give reasonable solutions according to the actual situation.

The waterproof coating can not be directly pasted with tiles, and the waterproof layer should be covered with 20mm thick 1:3 cement mortar, and then the surface layer or tiles should be pasted.

Hello, about your question I think 1, after the wall is made of waterproof coating, we must not be able to directly paste the wall tiles on it, we need to make a protective layer of mortar waterproofing agent on the wall, and we can paste the tiles after the mortar protective layer is completely dry, and the quality of the tiles will be better and better, so that the water absorption rate of the tiles will be reduced, and it is difficult to meet our needs by using the sand cement pasted tiles used to pave.

2. And for the current waterproof coating base is mainly based on the concrete wall, we only need to do a good job of waterproofing before we can paste the tile, but now the market also has a waterproof coating that can be done directly on the tile, but in fact, this method is still unreliable, and there is basically no waterproof effect after the best.

3. Can you directly paste tiles directly on the waterproof coating, but also depends on our construction quality and material quality, at present, there are cement mortar waterproof coatings on the market, so that the waterproofing can penetrate into the wall well, forming a better waterproof layer, and the adhesion between the surface and the tile is also very good, and it can also prevent mildew.

In fact, you can paste it directly, so that it will not damage the waterproof material, and many decorations are pasted like this, such as the kitchen and bathroom, it is impossible to apply waterproof tiles.

The waterproofing paint can be air-dried and then the tiles can be pasted with a cement mixture.

It is not possible to brush waterproof paint directly on the tile.

The use of waterproof coating must be on a clean, firm and flat base surface to form a strong adhesion, and directly painting waterproof coating on the tile can not really achieve the waterproof effect.

The properties of waterproof coatings are as follows:

1. Solid content.

Solids refers to the proportion of solids contained in a waterproofing coating. Since the solid components in the paint form a coating film after brushing, the solid content is closely related to the thickness of the film and the quality of the coating film.

2. Heat resistance.

Heat resistance refers to the fact that the waterproof film after the waterproof coating is formed does not soften and deform at high temperatures. Non-flowing performance, i.e., high temperature resistance.

3. Flexibility. Flexibility refers to the ability of the film layer of the waterproof coating to remain flexible at low temperatures. It reflects the application and use performance of waterproof coatings at low temperatures.

You can apply transparent waterproof glue directly on it, but one thing is that it cannot be broken with sharp objects, and it is better to apply several more layers.

The use of waterproof coating must be on a clean, firm and flat base surface to form a strong adhesion, directly on the tile waterproof coating is not really able to achieve the waterproof effect, because the surface of the tile has a layer of enamel, the waterproof layer on the surface of the tile is easy to cause falling off, can not be firmly bonded with the base layer, there is a kind of propaganda on the market "can be waterproof and seepage waterproof agent without smashing the floor tiles" In fact, it is not a waterproof coating, it needs to be mixed with cement and concrete, is an additive, It does not have the waterproof function itself, but only through the mixing of cement and mortar, the density of the cement is increased to achieve the waterproof effect, but this is a rigid waterproof, after a long time the rigidity is easy to produce cracks, to completely plug the leakage must remove the decoration layer and protective layer.

Generally, it is not possible to brush waterproof paint directly on the tile, because the use of waterproof coating must be on a clean, firm and flat surface to form a strong adhesion, if the waterproof coating is directly painted on the tile, it is impossible to really achieve the waterproof effect we want, because the surface of the tile has a layer of periphery waterproof layer on the surface of the tile is easy to cause falling off, and it is impossible to bond firmly with the base layer.

Shuanghong nano penetrating waterproofing agent.

Colorless and transparent, with unique waterproof properties, can penetrate into the inside of the cement substrate, save the dosage, and can construct 4-5 square meters per kilogram. It can adapt to a variety of substrates, such as walls, lime, cement mortar stucco layers, concrete surfaces, and can also be used on ceramic tiles, mosaic joints, with waterproof and color retention effects. It is the best waterproof material for direct painting on ceramic tiles.

If you brush it directly, the effect is not very significant. Downward seepage may also be due to the floor tiles. Some floor tiles will absorb water if they are not of high quality. It may also be that the gaps are not well handled when the masonry is done.

No, the building is solid and easy to apply waterproof coating is a waterproof project when the blank is specially done, and what you need should be a brick-free waterproof type.

We must pay attention to the use of cement mortar, we must protect the waterproof coating, so that we can better waterproof, pay attention to the selection of ceramic tiles, and pay attention to the choice of ceramic tile adhesive.

Before tiling, the wall should be kept flat, and the waterproof paint should be applied particularly flat, so that there will be no hollowing.

You can start by laying a layer of cement. Wait for the cement to solidify before pasting the tiles, pay attention not to be too fast, otherwise it will be packed.