When decorating, the wall of the bathroom is not waterproofed, how to remedy it?

Many toilet water seepage and leakage are caused by seepage from the tile gap to the ground, so since the bathroom is not waterproof and the tile is pasted, then we start from the tile gap to do a good job of leakage. What should I do? If there is a water leakage problem, or it has never been waterproofed, then you have to remove the floor tiles, as well as the bottom 30 cm of the wall tiles, re-waterproof on the ground, use flexible waterproof mortar, or use membrane waterproofing, and do a closed water test for 24 hours after waterproofing.

As the flow of water increases, the water will slowly penetrate into the downstairs, causing the roof downstairs to leak, and it will also penetrate into the other side of the wall, resulting in water seepage and resurgence on the other side of our wall. For you in this case, it is more troublesome, if the developer has brushed a waterproof, it may be better, but if there is a change to the water or the ground is slotted, it will not work, and the wall must be slotted by the electrician There is a high chance of water seepage. If the wall is thin or lightweight, it is best to waterproof the entire wall.

This can only be planed, re-do waterproofing, is the most foolproof, save trouble, and downstairs neighbors awkward, there are also a lot of surface waterproofing on the market can be sold, temporary brushing can also be used, but the symptom is not a cure for the root of things, waterproof is like building a house to lay a foundation, there is no remedy to do waterproofing, need to pay attention to several special places, such as the joint between the wall and the ground, the joint between the water pipe and the ground, these areas are very prone to water leakage.

If you want to not plane tiles in the short term, there is also a way to not leak, that is, to use acrylic transparent waterproof brush several times to form a waterproof film on the surface of the tile to achieve the effect of waterproofing. Do the lower surface waterproofing or buy a separate bath room and then take 10,000 steps back to take a shower or something, as long as the tiles find the slope to find a good good water will not leak I am afraid of endless flushing or driving the washing machine all the time Others actually have little impact.

You can buy your own waterproof paint to apply, as long as the bathroom is dry, you can use the construction.

The best thing to do is to warp all the tiles off, and then re-tile them after waterproofing.

We can find a decorator and ask him to pass it on to us, so that there will be no leakage of the bathroom wall, so we still have to hurry up to deal with it.

At this time, buy a waterproof paint and apply it to the wall of the bathroom, or put a layer of waterproof wallpaper on the tiles, so that it can be remedied.

As we all know, the most important thing in toilet decoration is waterproofing. If you cut corners during decoration and don't do waterproofing, there will be a lot of trouble later. After using it for a period of time, it is easy to seep out of the ingots, fall off the tiles, mold and other phenomena, which seriously affects the use experience of the toilet.

First of all, we need to look for the cause of the water leakage, whether it is a problem with the water pipe or the waterproof layer. For example, the leakage part is not waterproof; The height of the waterproof layer is 180cm lower than the conventional standard; Later pipeline construction affects the waterproof layer; waterproofing material quality problems and so on.

Once the location of the leak is located, it is necessary to remediate it according to local conditions. If there is a crack in the pipeline, the pipeline should be replaced in time; If there is a leak at the pipe joint, it should be reinforced; If the waterproof layer is too low, you need to make a high waterproof layer; If you use waterproof products such as sealants, you should have a clear understanding of their brand. If you have doubts about the quality, the first choice is well-known big brand products, which are more guaranteed.

If it is waterproofing, pay attention to the details: whether the base layer is smooth and clean; Whether the waterproofing of key parts such as the connection of the ground wall and the connection of the sewer mouth is done well should be checked many times; The wall waterproofing project shall not be less than 180cm, and the closed water test shall be carried out within 24 hours after the completion of the construction.

The water level height and time of the closed water experiment should be carried out in strict accordance with the standard. Bathroom waterproofing should be resolutely implemented to prevent the mainstay, the principle of combining water fortification and investigation, in the decoration process, we must do a good job of active waterproofing, there must be no water leakage, in case of water leakage. Otherwise, if you find a water leak after moving in, it will not only be troublesome to do waterproofing, but the cost will be 3-5 times that of active waterproofing.

Bathrooms are not waterproofed. Probably still being renovated. I guess after pasting the floor tiles, I found that it was not waterproof.

That's good. We are renovating.

We can still do it. Let's rebuild it, cut all the way down to the bottom of the caisson. Don't just knock out the floor tiles, waterproofing the screeds, or overhead prefabricated panels.

Because in this way, the water seeping into the pores of the tile, do not go, accumulate in the mortar layer, for a long time, it will breed bacteria, mold, and serious water will enter from the threshold, the inlet and outlet of the pipe, resulting in the door of the bathroom, the opposite aisle, the basic surface of the living room and the room putty moisture absorption, resulting in the delamination of yellow and black bubbles, and so on.

How to remedy the waterproofing of the bathroom wall.

1. If the wall is not waterproofed, you need to put the wall close to the root of the wall.

Bricks and floor tiles are knocked open, waterproofed again, and tiles are pasted after the waterproofing is done after the water test is successful.

2. If the waterproofing at the bottom of the wall is not done, you need to knock all the floor tiles open and do the waterproofing again.

3. The waterproofing of the wall is not done due to the damage of the drainage pipe, and the new water pipe needs to be replaced.

The right way to waterproof your bathroom.

1. Brush the waterproof paint for the first time.

Before brushing the paint, the base surface should be cleaned clean, there should be no foreign matter, and the base surface should be kept dry, so as to ensure that the coating and the base surface are more tightly bonded, and there will be no falling off in the later stage. When painting, it is necessary to ensure that the painting height of the entire base surface is the same, and the thickness of the painting must meet the construction requirements.

2. Brush the waterproof paint for the second time.

After the first coat of paint has dried completely, start brushing the second coat of paint. This will make the waterproofing effect better.

3. Lay a protective layer.

If it is just a simple waterproof layer, it is easy to be damaged in the later construction. Therefore, a protective layer should be made on the surface of the waterproof layer. The protective layer should be fully covered with the waterproof layer to ensure that it is tightly bonded with the base layer, so that the effect will be better.

4. Closed water test.

After completion, the closed water test must be done, and there will be no water leakage after the experiment, so as to be qualified. If there is a water leak, it needs to be re-waterproofed.

The bathroom is a space with more water, if the waterproof is not done well, the comfort of life will be greatly affected, so it must be waterproof before it can be used normally.

Knock the tiles off and re-apply them to waterproofing. The bathroom must be waterproof, if the room is not waterproof, it must be remedied in time, otherwise the downstairs residents will become a water curtain hole, resulting in unnecessary disputes.

In such a situation, you can choose to lay tiles on the wall of the bathroom, because this can play a very good role in thermal insulation, and then it can also play a waterproof effect to a certain extent.

You can knock down the wall of the bathroom and re-do the relevant waterproof layer work, which is relatively difficult.

Remedy for bathroom wall not waterproofing: After finding a place for water seepage, it is necessary to carry out rescue according to the situation. If there is a gap in the pipeline, the pipeline should be dismantled and replaced immediately; Water seepage at the pipe joints requires structural reinforcement; If the ground waterproofing is too low, you need to do high ground waterproofing; If you use waterproofing materials such as sealants and other architectural coatings, you will have a clear understanding of their brands.

If you have doubts about the quality, you can choose famous and well-known brand products, which is more ensured. If it is to do moisture-proof, pay attention to the details: basically whether it is leveled and tidy; Whether the moisture-proof in key areas such as ground wall connection and sewer mouth connection is done well should be repeatedly checked; Wall waterproofing project, not less than 180cm, within 24 hours after the construction of the project, to do a good job of irrigation test.

The relative height and duration of the water level of the irrigation test should be carried out in strict accordance with the specifications. Bathroom waterproofing should be implemented from beginning to end in order to prevent problems before they happen, the surface and water cloth and inventory are closely combined with the standard, in the decoration process, we must do a good job of positive moisture-proof, there must be no water seepage, to prevent the concept of water seepage. Otherwise, after moving in, it is found that there is water seepage, and then it is inconvenient to do moisture-proof, and the cost is 3-5 times that of active waterproofing.

Toilets are not moisture-proof. It is quite possible that it is still being renovated in the interior.

Before brushing latex paint, the datum should be cleaned up, there should be no dirt, and the datum should be kept dry, so as to ensure that the architectural coating is more closely bonded to the ground, and it will not fall in the middle and later stages. When painting, it is necessary to ensure that the relative height of all datum surfaces is the same, and the thickness of the brush should meet the construction requirements. After the first coat of architectural paint is thoroughly dried, the second coat of material is brushed.

In that way, the actual effect of moisture protection will be stronger.

If the protective layer is simply waterproof, it is very easy to be destroyed in the later construction process. Therefore, a protective layer is also needed on the surface of the moisture-proof layer. The protective layer should cover the ground as a whole and be waterproof, so as to ensure close bonding with the rural grassroots, so that the actual effect can be stronger.

Irrigation test, after the end of the irrigation test, must do the irrigation test, after the test will not occur water seepage problem, can be regarded as up to standard. If there is water seepage, it must be re-proofed. The toilet is an indoor space with more tap water, and if the waterproof is not done well, it is very harmful to the comfort of life, so it must be strengthened to prevent moisture before it can be started normally.

1.If the toilet is not waterproof, there will be water leakage in the process of using water. We can find the leakage point and check if there is a problem with the water pipe.

2.If the water pipes are good, it is determined that it is the problem of the waterproofing layer. If it's really a problem with the waterproofing layer, we need to fix the defective waterproofing layer.

We can use brick joint filler or repaint.

It is very important to make the wall of the bathroom waterproof, if it is not waterproofed, it is likely to cause water leakage, which will affect the use of bedrooms and other functional partitions, so it should be repaired as soon as possible.

If the wall of the bathroom is not waterproof, then you can use it like this first, and then ask a professional construction team to rectify it when there is a problem.

The bathroom will not only install a toilet, but also install a washbasin, shower, etc., will often be in close contact with water, so it is very important to do waterproofing on the bathroom wall, if you do not do waterproofing, it will lead to leakage and water seepage on the floor or wall, which makes many homeowners feel very annoyed, so what to do if the bathroom wall is not waterproof, what can be done to remedy the bathroom wall without waterproofing? Next, let's take a look at it.

1. What should I do if the bathroom wall is not waterproofed?

1. If the bathroom wall is not waterproofed, you can smash the connection between the floor drain and the drainage pipe and the floor slab.

2. Stir the mortar and alum stone expansion agent ratio, then stir evenly, apply it to the open position, and apply it evenly for 4 weeks.

3. If the bathroom is not decorated with a bathing area, it is dry and wet separation, in this case, it is no problem not to do waterproofing, and no special remedy is required.

4. If the bathroom is not waterproof, the water vapor will seep into the tile joints of the wall and the ground, resulting in the leakage problem of the floor slab, which will bring trouble to the residents downstairs, especially in the rainy area, if you do not do waterproofing, this will lead to mildew on the wall and water seepage, so the shower area must be waterproof, and there are strict requirements for the waterproof height, generally about 1.8 meters.

Second, what is the way to remedy the bathroom wall if it is not waterproofed.

1.You can make a waterproof layer on the back of the wall, which can prevent the furniture from becoming moldy, of course, if the opposite side is someone else's wall, this method will not work.

2.You can use waterproof glue to fill the gaps in the wall tiles to make up for the lack of waterproofing.

3.If the bathroom is not waterproofed, you need to install the bathtub far away from the wall when using the bathtub, and buy a waterproof shower curtain, but this method is not a long-term solution.

4.Tap the tile with your hand, if you find that there are many hollow places, it means that the tile is not pasted well, and you need to reopen the tile to make waterproofing.

5.There are not many empty positions of the tile, which shows that the quality of the tile is very good, it has a waterproof function, at this time, you can use the acetate map to infiltrate into the tile, and then use sodium silicate to wipe it repeatedly, so that you can make up for the water leakage of the tile to play a waterproof role.

6.Bathroom wall waterproofing must be done, did not listen to the opinions of others, bathroom shower area tiles will be in contact with water for a long time, water deep into the tiles will lead to the phenomenon of water seepage and mildew in the canopy, so users must do a good job of waterproofing the wall when decorating the bathroom.

The above information is prepared for everyone about the bathroom wall is not waterproofed what to do, the bathroom wall is not waterproofed what to do to remedy the content, here is the end, I believe that by reading the above information on the bathroom wall waterproofing, there is a deeper understanding, if you want to know more, please continue to pay attention to the hunting Internet café.