Is it better to have a primary color or a layer of blue?

Of course, the new iron pot is the primary color of the iron pot, which is better! So it's best not to use the one that has a blue coating! Because all coated cooking utensils will inevitably have concerns about the adverse health ingredients in the coating.

For a new iron pot, it is better to have a layer of blue, because a layer of blue is fired at a high temperature, and after a certain amount of processing, such an iron pot is still better.

It's all about the same, even if it's blue, it's baked at a high temperature, and it won't have any impact on health, so just buy what you like.

1.Inflate the balloon to the desired size (need to compare and confirm with cupcake paper molds)2After inflating, tie each balloon with duct tape.

Bamboo skewers are fixed Please be sure to stick them firmly and avoid them.

Falling halfway during a long period of drying leads to deformation failure.

3.Soak the gelatin tablets in edible ice water to soften (ice water is about the same amount.

7-8 minutes full), softened and dried the water before adding.

30g of cooking water is heated through water until gelatin is completely melted.

4.Be sure to smear a little oil on the balloon before dipping it into the liquid gelatin to avoid not being able to get off the mold!

5.If there are bubbles in the gelatin after heating and melting, the bubbles should be scooped up or set aside before use.

There will not be too many bubbles on the surface to affect the appearance.

6.If the weather is cold, you can add a basin temperature under the container.

The water remains in a liquid state so that it does not start to solidify at the end of use.

Sprinkle with natural silver edible glitter.

7.Stick the bamboo skewer on the styrofoam.

Allow to dry for about 24 hours and wait until it is completely dry.

Dry (The weather in Taiwan is humid, such as wet.

Spend more time in Takasu).

8.Wait for the surface gelatin to dry completely.

It doesn't feel sticky or cold to the touch.

Cut the balloon slightly and slowly release the air to demold.

After five minutes of washing, wash it several times with clean water, and then dry burn it over high heat to burn off the coating on the surface. In the process of dry boiling, the edge of the pot should be shaken constantly to ensure that the iron pot can be heated evenly

Summary. When the wrought iron pan is heated and boiled, you will notice that the inside of the pot turns blue, and this process is called "blue".

When the wrought iron pan is heated and boiled, you will notice that the inside of the pot turns blue, and this process is called "blue".

Because there is a layer of ferric tetroxide on the surface of the wrought iron pot, it will form an oxide film in the pot, which can reduce the contact between iron and oxygen and avoid rust in the iron pot.

The iron pot is burned blue, which is related to the substances contained in the iron pot, mainly because the material of the iron pot is not of high purity and will turn blue.

The carbon content of the wrought iron pot will be less than the characteristics are that the iron is soft and plastic, but the disadvantage is that it is easy to deform and the strength is relatively low.

It generally doesn't matter if the newly bought iron pot turns blue after using it once, which is a normal phenomenon in metal technology, which is caused by uneven heating. After the iron pot is fired for a period of time, a layer of oxide film will be formed on the surface, so that the surface will not appear blue.

It is normal for an iron pot to turn blue after boiling.

Then brush the wall of the pot with lard, ** heating, which can make the inner wall of the iron pot form a protective film to prevent rust. 2. Don't clean the hot pot immediately after frying, the pot is still very hot, at this time, if you add cold water to produce smoke, you should wait for the iron pot to cool down before rinsing, or rinse with hot water.

Hello, how else can I help you?

This is a normal "bluing" process and does not affect the use!

Under normal circumstances, before the official use of the iron pot (without the simple coating), it is necessary to do a "pot raising" work, that is, to smear the pot that is very hot and hot with lard skin, so that after a few times, the iron pot is not easy to grow rust and not easy to stick to the pan!

When the iron pot is burned very hot, the hot iron slowly cools down in the air, and an iron oxide film will be formed on the surface of the iron pot where it is not covered by lard, and this film is dark blue, so it is called "blue"!

In daily use, do not use wire wipes, dish soap and other things to wash the pot unless necessary, otherwise it will lose its effect and you will have to re-raise the pot!

In the picture below, you can see the difference between the pot in the lower left corner and other pots after raising it!

Summary. Hello, this one is because there are impurities in the iron pot, so it will appear blue. This white iron pot turns blue when burned because a layer has formed on the surface. Ferric oxide. So it's blue.

Hello, I'm helping you sort out the answers to your questions, please wait a while Hello, this Zen is because there are impurities in the iron pot, so it will appear blue. This white iron pot turns blue when burned because a layer has formed on the surface. Ferric oxide.

Therefore, the blue He Meng code is presented.

I can't turn blue with this.

The first is that the method is not right, and the second is that the iron pot contains more impurities.

I've burned it for a long time.

There is no fat or meat skin to smear the pan.

Can such a pot be used, of course, you can use the current pot, and the better pot does not need to be boiled. The manufacturer has already opened it.

Summary. Hello dear, this means that you are using a wrought iron pot, the quality is relatively good, the pig iron pot has many impurities, and the bottom of the pot does not turn blue after burning. The bottom of the wrought iron pot turns blue, which is a natural phenomenon that occurs when iron meets high temperatures, and the chemical changes that occur when iron is oxidized when it is heated.

Hello dear, this means that you are using a wrought iron pot, the quality is better, the impurities of the pig iron pot are scattered, and the bottom of the pot does not turn blue after burning. The bottom of the wrought iron pot turns blue, which is a natural phenomenon that occurs after the iron meets high temperatures, and the chemical changes that occur when the iron is oxidized by hand when it is heated.

The natural phenomenon that occurs after iron meets high temperatures, and the chemical changes that occur when iron meets heat oxidation, normal phenomena.