How to do white and black open paint 40

Open coating is a set of new coating technology formed by using wood paint varnish and white paint series products, with the reasonable foil of color, and with the help of special construction technology. Compared with the fully enclosed coating, it can highlight the characteristics of fresh and bright, it not only has the characteristics of environmental protection and health, but also can be painted in hundreds of different colors according to different needs. According to different construction techniques, to create different decorative painting styles, is the current interior decoration and high-end home decoration fashion choice.

Yiduowei furniture panel furniture is the use of open paint technology, so that the color of the home is more vivid and changeable.

Construction technology: 1. Material selection:

Choose woods with deep eyes, uniform and smooth grain, and hard timber, such as oak, cherry, ash, etc.

Second, cable material treatment:

1.Confirm that the cable material is dry and clean, and sand with 240 sandpaper to remove the wood thorns;

2.Use a brush spray gun to remove floating dust from the surface.

3. Bottom rubbing color:

1.Use the color polish to directly modulate the color you need, 70% of it, and then fill the color according to the color requirements;

2.Wipe the prepared color directly on the cable;

3.Normal construction after drying.

Fourth, the construction primer.

1.Apply a sealing primer on a colored substrate, preferably sprayed;

2.Stir the paint evenly according to the correct ratio and let it stand for 15-20 minutes until the bubbles are eliminated;

3.Uniform spraying brushing, grinding and dust removal after drying;

4.Depending on the degree of openness, the number of times the primer should be applied is determined.

Fifth, the top coat color repair.

1.The topcoat is modified according to the desired color, using the selected topcoat as the base material. Mix the color of your choice with a color modifier, dilute the base material appropriately, stir evenly and spray the application;

2.According to the needs of the color, determine the number of color repairs, and polish and remove dust after drying;

3.Once the color is determined, spray the topcoat on one side.

White body sanding, sanding, spraying white primer, drying, applying black background, sanding, spraying white topcoat. After applying the black background, the polishing should be thorough, and the white top coat should be sprayed thinly.

1. It must be wood with large grains, such as American oak, water cedar willow, oak, etc.;

2. Do not make putty, directly make the primer; Mountain stove.

3. The spraying should be thin, and the paint should not be too thick;

4. The grinding should be clean, and the dust in the Yuweihong grain holes should be blown clean before spraying.

One primer and two topcoats can cover.

The construction difficulty of yellow background and white surface open paint is high, and the requirements for the substrate are high, which is suitable for ash panel as the foundation or the use of flat color rubbing treatment, the latter is more difficult; It is recommended to use the former, and use water to make Bichamu substrate for the panel! According to personal experience, the order of Shi Qing trembling on the yellow background and white surface should be reversed, that is, the face color should be done first, and then the background color should be yellow, the texture of the ash panel is clearer, and there is no need for putty to lay the foundation, it is recommended to paint the white paint directly (nitro paint is better), be sure to retain the texture of the depression of the wood grain, the painting process is the same as the general nitro paint, and then use the color treasure to wipe the color after the white paint is done, and the color part will all enter the depression of the wood grain, which is displayed as the depression of the wood grain is yellow, and the protrusion is white. After doing a good job of wiping the color, wait for drying and grinding, remember to cut the bottom is not visible, it is recommended to grind the 600 mesh abrasive cloth with water, and finally spray the nitro varnish again after checking that there is no problem to achieve the effect!

Ash panel to do open paint, how to make the wood grain black, the surface is light gray, solve!