How to make a water sticker, how to use a water sticker How to use a water sticker

Production process:

Step 1: Make the water sticker pattern you need first (first draw the water sticker pattern we want on the computer, the size. Color.

Pattern here. It is not a good way to scan the output of the water sticker, the resolution is not high, and the effect will be much worse.

Use vector output as much as possible for pattern output, and use software to draw the required diagram yourself).

Step 2: Output (print) to the water sticker.

Step 3: Since the inkjet ink is water-based (melts in contact with water), we need to spray transparent paint as a protective layer. (The purpose of varnish is to protect the printed ink, because the ink of the general inkjet machine is water-based, and it melts when it encounters water, cut the pattern we need and then spray the protective paint, when spraying the transparent protective paint, spray thinly, do not spray too thick, or too shallow).

Step 4: After drying, cut the pattern to a suitable size, put it in water to soak quietly, separate the membrane paper, and then paste it on the object, and slowly push out the bubbles and blisters inside the paste with cotton fiber until smoothed.

How to make water stickers.

There is a thing called water transfer paper (also called water transfer paper), it has two kinds, one is varnish-free, the other is varnish-free, and what we want to talk about here is this method of making water stickers from varnish-free water-to-paper.

Tools and materials: one ordinary inkjet printer, one plasticizer (also known as glue machine), one water-to-paper without varnish.

Production process: First of all, the pattern to be printed is processed with drawing software, this kind of varnish-free water-to-paper has a total of two sheets, one is the bottom paper, the other is a transparent film, and the pattern we want to print is printed on this transparent film. There is generally an indicator mark on the transparent film, and the side where the indicator mark is located is the printing surface of the pattern, put the transparent film into the paper inlet of the printer, align it with the printing surface, and start printing.

After printing, allow the clear film to cool down and let it sit for more than two hours with the print side facing up. Then the side of the transparent film printed with the pattern is aligned with the white side of the bottom paper, and after alignment, it is put into the plastic machine to make the two sheets of paper completely glued together, and then let the water paste cool for a period of time, and after the water paste is cooled, the transparent film is torn off, so that a water paste is manufactured.

Precautions: 1. The printed pattern is in the opposite direction to the pattern on the computer.

2. The printing surface must be the side with the indication mark.

3. The transparent film must be cleaned before bonding with the bottom paper.

4. The transparent film and the bottom paper must be completely bonded.

5. The use of the made water sticker is the same as the use of the model water sticker, I hope it will be useful to you.

The water sticker is as follows:

Tools required: Cutting pad, tweezers, shallow water tray, model knife, paper towels and cotton swabs, water stickers, water sticker softener.

1. Once you finish the color spraying of the model, you should try to ensure that the paint surface of the model is smooth and complete, and the smooth surface will ensure that the water sticker you want to add can be better stuck on the surface of the model, even if the initial paste is not correct, it is easier to adjust the position of the sticker.

2. Engrave the sticker pattern from the whole sticker, once the pattern is completely cut, you can put it into the shallow water tray and soak it in water. It takes about a minute to soak the stickers.

3. Use a cotton swab dipped in a little water to apply the water sticker to the position where the sticker needs to be pasted.

4. Pinch up the water sticker with tweezers, put the pattern face up on the model, gently press the water sticker with a cotton swab, and pull out a little bit of the base paper.

5. Use a knife (or cotton swab) to adjust the position of the water sticker.

6. Use a paper towel to absorb excess water and gently press out the bubbles.

7. Now, after correctly aligning the water sticker, you can brush a little water sticker softener (in this case, the green cover softener used by the county clerk) when brushing the action is gentle, do not let the water sticker move, if there are signs of movement, you must quickly adjust it with a knife or cotton swab.

Then use a paper towel to absorb the softener again, be very careful, if you use too much force or can't correct it in time, then the water sticker may be damaged.

The water sticker softener works very quickly, and the water sticker seems to melt away when you first apply it, but don't worry, if you use the water sticker softener correctly, then the water sticker can be firmly attached to the model and will not leave traces of the transparent part.

8. The water sticker has been pasted now, and the next step is to clean up the remaining transparent part, and then you can continue to paste the other part of the water sticker.

1. Use scissors to cut off the water sticker. Put the sticker in the water for 30 seconds, then remove it.

2. The water sticker will be separated from the carrier paper, and the water sticker will be transferred to the part to be pasted with a cotton swab.

3. Then use a dry cotton swab to absorb the water around the sticker.

4. Water stickers, that is, stickers that can only be used after water immersion. It is a new transfer technology that uses water as a carrier to separate the pattern from the bottom paper and then transfer it to the substrate to realize the principle of indirect printing. Widely used in:

Patterns of the appearance of various car models, electronic products, room supplies, daily necessities, indoor building materials, etc.

First put the water sticker in the position you want to paste, and then wet the back of the water sticker with water, etc., and then take the water sticker, and the pattern will be printed to the place you want to print.

Cut the sticker, put it in the water for a few seconds, then pick it up and put it in the position to be pasted, press it, scrape it, and don't let the sticker move, otherwise it will be broken.

The transparent plastic paper was removed, and the pattern was pasted onto the model.

Put it in the water, pick it up, and you can stick it.

Water stickers are usually made by a printing shop that makes stickers.

However, the printing house is to have a quantity, if you print hundreds of copies at a time, if your shape is special, you have to cut along the pattern, then you have to pay a knife mold fee, I remember that there is a special whiteboard water sticker on the Internet, you go to ** to see, and then you can print the pattern you designed on it.

Water transfer paper transfer method:

1. Uncover the protective paper, cut out the pattern that needs to be pasted, and immerse it in clean water for about 1 minute 2. Take out the transfer paper, the surface of the paper will be very smooth and the pattern can slide on the surface of the paper;

3. Clean the surface of the pasted product, slide the pattern onto the product, align the position, and scrape the moisture under the pattern layer;

4. Naturally dry for more than half a day, the pattern has been well attached, such as the tearable film water mark, then tear off the adhesive film;

5. According to the product requirements, the varnish spray or baking treatment is carried out, that is, all the transfer printing has been completed.

Step 1: Wipe the surface of the object to be repasted clean, and remove the transparent protective film on the surface of the water sticker;

Step 2: Soak the water sticker in water for 20-30 seconds until the painting is completely soaked;

Step 3: Place the painted pattern surface on the object, and use a ruler, eraser, magnetic card and other items to fully scrape off the moisture and air from behind;

Step 4: Leave for about a minute and moisten the back of the painting with a damp cloth.

Step 5: Wait for one minute to move the bottom paper, if it can be moved, then smoothly remove the paper in one direction, and the pattern will be transferred to the object;

Step 6: Once the pattern is completely dry, wipe it with a damp rag and you're done.

Step 7: Wait for the film to dry naturally, tear off the film, spray the varnish, and then put it in the oven to bake. Better results.

The model water sticker should first cut the required part from the whole sheet of paper and soak it in warm water for about 1 minute.

Then gently try to twist it with your fingers. Confirm that the glue between the top layer of the plastic film and the bottom adhesive paper has melted, and the plastic film can be separated, and then remove it from the water.

Place it near the location on the model where you need to attach the pattern, and use your fingers to gently slide the plastic film printed with the pattern from the backing paper to the surface of the model. The liner paper can be thrown away.

After adjusting the position of the pattern accurately, use a tampon swab to absorb the residual water between the sticker and the model, and squeeze out the residual air bubbles at the same time. Then let it dry, and the plastic water stickers printed with various logos can be firmly glued to the surface of the model.

Step 1: Soak the water sticker in water for about 10-20 seconds;

Step 2: Remove the water sticker when it slides freely on top of the liner (together with the liner);

Step 3: Place the water sticker on the surface of the object, slowly pull out the bottom paper, and let the water sticker rest relatively flat on the surface of the object;

Step 4: Then drive out the water from the part of the water sticker that is in contact with the surface of the object, so that the water sticker is completely in contact with the surface of the object;

Step 5: Put it on static drying for 3-4 hours, that is, it is completely dry: (1) If it is a water label, it is not torn off the film label, and it can be sprayed with oil after drying; (2) If there is no film label, that is, the tear-off film label, tear off the surface film after drying, and then spray oil.