The bottom of the computer chair is made of steel pipe, will it wear out the floor?

The wheels of a computer chair can scratch the floor if used for a long time.

Here's how to make a computer chair on wheels without damaging the wooden floor:

1. Put a carpet under the computer chair to avoid scratches.

2. Use PU wheels, but keep the ground clean and hygienic. If there are some large dust particles, they will scratch the floor when moved.

The characteristics of PU infusion wheels: elasticity can achieve a certain shock absorption effect (even better than inflatable wheels), good grip, not easy to slip, more wear-resistant, and good comfort.

Extended information: The maintenance method of the computer chair is as follows:

1. Clean with water and detergent, avoid scrubbing with gasoline.

2. Do not dry clean, it is recommended to wash with water, and the water temperature should not exceed 40°C.

3. Do not place the chair in a place with high temperature and strong light.

4. Don't put the chair together with some organic solvents.

5. PU leather cannot be maintained like ordinary leather, please do not use commercially available care agents to spray the surface of the chair. It can be gently wiped with a damp cloth.

on Jan 30, 2020

Hello, if the part of the computer chair touching the ground is a steel pipe, it will definitely wear out the floor, it is recommended to go to the hardware or furniture store to buy a rubber sleeve to cover the corner of the chair, so as to avoid the computer chair from wearing the floor, if you can't buy it, you can buy a rubber pad to stick it can have the same effect.

Of course, the sheath will wear out after a long period of use.

Wear and tear is also possible.

Check the sheath regularly when you have time.

The cotton carpet under the computer chair is larger than the chair, 50 yuan a piece,,, and it is estimated that the cloth head market around the country is about the same. Does not affect chair dragging.

Use two layers of waste fabric to pour some sponge or cotton, then sew it up and loop the leather band, and sew a small lace on it. The weaving you are talking about is more troublesome. There's an easy way to knit it by hand.

PU wheels do not hurt the floor.

1. Large contact area.

2. PU soft material, hardness is lower than that of the floor.

You can take a look at Ruiyou's computer chairs, which are all PU spinner wheels.

Yes, there's no deadline for any floor, it's just a matter of time.

If you want to repair and continue to use, you must check the hole of the air rod and the middle air rod, the normal is to be stuck, the air rod is inserted too much, it must be a part in the contact position (air rod or five-star foot) is damaged, can not be stuck, replace the damaged parts.

It's best not to use it, be careful.

You still don't use it easily**.

Exactly the same problem as the landlord. The floors are all abrasive.

It is best to use laminate flooring for office use, and even if the solid wood is protected, it will not be completely guaranteed not to be damaged.

The feet of the general computer desk are wrapped in rubber, which is afraid of wearing the chair and floor, if you don't have rubber, you can pad something fast.

Generally speaking, there is some damage, and the best way to do this is to put a blanket under the stool to make it look good.

Non-slip and does not harm the floor.

Cloth covers on the four footbags of the computer chair.

Buy a larger cushion and spread it in the place where the computer chair often moves, and it is better to be thicker, so that the wheels move on the cushion and will not grind to the floorMaterial, I think it's better to be like that kind of floor glue, to be thick and soft, don't buy hard, use carpet is OK, but sometimes I'm afraid it will make it inconvenient for you to walk

For example, slipping, etc., the most troublesome and cost-effective thing is to use a large cardboard, but to fix it on all sides with adhesive tape, because the cardboard cannot be moved, but the glue left by those adhesive tapes may be more difficult to clean when you clean up in the future, but you can use alcohol or gasoline to clean, but it is also very troublesome to clean, so let you think about it yourself and see which way is more suitable.

PU wheels, but to keep the floor clean and hygienic, if there are some large particles of dirt, it will also cause scratches on the floor when moving. The characteristics of PU infusion wheel: elastic can play a certain shock absorption effect (even better than that of inflatable wheel), good grip, not easy to slip, more wear-resistant, and good comfort performance.

If you want to install the casters, you also use a hammer to knock on the small place in the middle of the casters, if you remove the casters, the plastic rubber sleeve in the middle of the feet is also removed, you have to go to the place where the computer chair is sold, sell a rubber mother suit, and then install a new caster (the feet are wood and iron frame, there will be a rubber mother cover, and the hardware feet and plastic feet do not use the rubber mother cover).

You can consider buying a carpet, a little larger, and put it under the computer chair, which not only protects the floor, but also can be non-slip, which is more appropriate

I think it's better to have a floor glue like that, it's thick and soft, and don't buy hard mats to put on it.

The most troublesome and cost-effective thing is to use a large cardboard, but it should be fixed with adhesive tape on all sides, because the cardboard cannot be moved

I think wrapping a soft jacket around the outside of the wheels will prevent the floor from being worn.

Buy a larger cushion and spread it where the chair often moves, and a thicker one is better.

It's better to be thicker, so that the wheels move on the mat, and it won't grind to the floor, the material, I think it's better to have that kind of floor glue, which not only protects the floor, but also can be non-slip, which is more appropriate.

You can use alcohol or gasoline to clean up, but it's also a hassle to clean up, so let yourself think about it and see which way is more suitable.

It's also a hassle to clean up, so it's up to you to figure it out for yourself.

This question is a bit difficult, and I personally recommend putting a rug (a little thicker) or a foam puzzle floor (the kind that prevents children from falling).

Personal preference for the latter.

Choose a silent wheel or a cushion underneath.

Generally, chairs with chair wheels will not damage the wooden floor, unless the quality is not good or the friction is too serious when sitting, maybe weight is also one of the small factors, haha.

Another point is that if you buy a chair, you can work on the floor and do a good job of maintaining the floor.