How to deal with the factory floor, the factory floor practice

Causes of the causes of concrete floor: (Henan Huineng Road and Bridge Details) (1) The cement strength grade is too low, resulting in the strength of the mortar not meeting the design requirements; (2) The cement mortar is stirred unevenly or excessive water is added during mixing; (3) The calendering times on the surface of the cement floor are not enough or are not compacted; (4) The calendering time of the surface of cement mortar is not well grasped or calendered after final setting. BC cement pavement sanding treatment repair material is used to deal with the situation of sanding on concrete floor, cement floor, wear-resistant floor, as well as old floor renovation ground and old wall renovation, wear-resistant floor, as well as various types of industrial warehouses, various types of logistics centers, various types of workshops, parking lots, all places with concrete or cement mortar as the base layer of ground treatment sanding, to increase wear resistance, hardness, color ground, after using this product has a good effect.

Remedies for cement floor ashing? Ordinary cement floor, concrete floor, terrazzo ground and the quality of the emery ground are not good enough to appear ground ash, this is because the strength of these ground surface layers is not enough, the wear resistance is not good, when the external force friction or impact, it is easy to appear ground ash. Prevention and treatment of cement mortar ground sand 1 Control the water-cement ratio of cement mortar, the water-cement ratio, and the water-cement ratio directly affect the strength of the mortar.

If the water-cement ratio is too large, the cement is too small, the water volume is too large, the ground strength is low, the surface is rough, not wear-resistant, and easy to sand. In addition to the hydration of water with cement, there is excess free water, which is to be slowly evaporated, resulting in countless capillary pores on the surface layer of the ground mortar, thereby reducing the compactness of the mortar, reducing the actual thickness of the cement mortar surface layer, and the decrease in strength leads to easy wear and sanding. In addition, too much moisture on the surface will prolong the calendering time of the surface layer, which may exceed the final setting time of the cement, and the quality of the ground cannot be guaranteed.

On the contrary, the water-cement ratio is too small, the cement is too much mortar dry and hard, the construction operation is difficult, and the ground is prone to cracks. Therefore, the consistency of cement sand in the surface layer is generally not more than 36mm.

How long can the car press be made of wear-resistant armored flooring, if it is a factory where many people walk, then armor or wear-resistant epoxy can be done.

Factory refers to all kinds of buildings used for production or supporting production, including main workshops, auxiliary rooms and ancillary facilities. Factories in industry, transportation, commerce, construction, scientific research, schools, etc. should be included.

1. The plain soil is compacted, and the compaction coefficient is not less than;

Thick Panax notoginseng ash;

m by 6 m cutting seam, the seam is filled with polyester containing ammonia trap and panicle ester;

Thick C30 fine stone concrete reinforcement 200 meters by meters 200 steel mesh layer of inorganic wear-resistant surface layer.

Ground 1 (ground in the workshop, load 3t).

Method: 1. The plain soil is compacted, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

MX6M cutting seam with polyurethane filling in the seam.

Thick C30 fine stone concrete reinforcement 6@200x200 a layer of reinforcement mesh Inorganic wear-resistant surface layer Ground 2 (the ground in the workshop, the load is 5t, used for the ground of other plants except ground 1) Method: 1. The plain soil is compacted, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

Thick C20 fine stone concrete.

MX6M cutting seam with polyurethane filling in the seam.

Thick C30 fine stone concrete reinforcement 6@200x200 a layer of reinforcement mesh inorganic wear-resistant surface layer 3 (substation).

Method: 1. The plain soil is compacted in layers, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

Thick C20 concrete cushion.

4. A cement slurry (mixed with construction glue thick 1:3 cement mortar screed layer 6, thick polyurethane waterproof layer (two)

Thick C25 non-flinching fine stone concrete (with limestone, dolomite aggregate) Ground 4 (washroom, toilet floor).

Method: 1. The plain soil is compacted, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

Thick C20 concrete cushion, with the grinding 4, cement slurry (mixed with construction glue).

5, the thinnest 30 thick C20 fine stone concrete to find 1% slope, slope to the trench or floor drain 6, thick polyurethane waterproof layer (two), around along the wall over 250 high thickness 1:3 dry hard cement mortar bonding layer surface sprinkled with cement powder.

300*8 thick color non-slip floor tiles, dry cement wiping joints (the color is set by Party A, and the width of the joints is 2mm) Ground 5 (tool room, auxiliary material room, air compressor station and pump room ground) Method: 1. Plain soil is tamped, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

Thick C20 concrete cushion.

4. A cement slurry (mixed with construction glue).

Thick C20 fine stone concrete, sprinkled with 1:1 cement stone on the surface with the smearing of the floor 6 workshop office part of the floor (floor tile floor, used for the rest of the room and aisle floor) Method: 1. The plain soil is compacted, and the compaction coefficient is not less than.

Thick Panax notoginseng ash;

Thick C20 concrete cushion.

4. A cement slurry (mixed with construction glue).

Thick 1:3 dry hard cement mortar bonding layer surface sprinkled with cement powder.

600*10 colored ceramic floor tiles, dry cement wiping joints (color, specifications or Party A's own customization, joint width 2mm).

Plain soil tamping and then cushion and finally do the surface layer generally I recommend you to do the color solid stone floor is hard and wear-resistant, no dust, uniform color, warranty up to 20 years, not expensive.

First of all, the base layer must be designed to meet the requirements of the specification with bearing capacity and deformation.

Surface layer: epoxy resin, artesian level, etc., are not suitable for the workshop floor surface layer after practical tests, and most of the new workshop floor surface layer is made of gold steel sand floor, which is pressure resistant and friction resistant.

Plant ground treatment method:

1.The floor of the workshop that is not afraid of dust can be paved with cement paint, such as paper mills, machinery factories widely use cement floors.

2.The floor of the workshop that is afraid of dust can be paved with floor paint, such as the current dust-free workshop widely uses floor paint.

Tell us what the plant is for, such as what products are being processed.

You can find Wuhan Qifeng to do hardened floor treatment, after all, it is a professional floor engineering company, and all aspects are more worry-free. The specific steps are as follows:

1.Remove the floating ash on the surface and keep the construction area clean and dry;

2.Pour 1-3 cm of concrete on the damaged ground, level the trowel, and harden it after 28 days of curing;

3.The concrete sealing curing agent is evenly brushed on the concrete floor after mixing, soaked for 4 hours, and then removed with clean water after 4 hours, and polished after the ground is dry;

4.When the ground is polished to a weak light, the floor of the plant is polished, and the polished ground can see obvious gloss;

5.Use dust to remove the dust on the ground and clean the construction site, that is, the renovation of the factory floor is completed.

The new workshop flooring material Tecan (DDK) 2000 9979, Che Bottom solves almost any floor problems such as excessive wear and tear on the factory floor, paint delamination, dust, moisture or contamination. It is now being used more widely in different fields of busy industrial plant floors, heavy forklift floors, workshop floors and other environments.

The main advantages of the wear-resistant flooring of the new workshop include the following:

Suitable for use with forklifts, pallet trucks, cars, heavy goods vehicles and high capacity pedestrians.

A smart and modern look with customizable colors allows you to quickly build a bright, clean, protected and efficient industrial floor.

Excellent durability, far more than traditional wood flooring, epoxy resin flooring, etc., and more flexible and efficient.

Quiet with constant temperature, insulation and noise resistance, protection from cold and moisture, help protect existing plant floors.

More durable and easier to maintain. Heavy-duty and wear-resistant. At the same time, local damage and partial replacement.

If there is dust and dirt on the floor of the plant, it can be directly rinsed with clean water.

If there is any grease on the floor, you need to use an oil cleaner to clean it.

If the oil stain on the floor of the factory is too heavy, or the ground is damaged, it is necessary to polish and polish the damaged ground to repair the defective ground.

Generally, epoxy mortar is used to flatten the floor.

Type: pressure-resistant mortar epoxy floor paint;

Application: industrial plants, parking lots, general commercial grounds;

Features: Solvent-based rolling floor, beautiful surface dustproof, wear-resistant, smooth surface, high hardness.

Thickness: Process flow: 1. Plain ground treatment: do a good job of repairing, polishing, and dust removal according to the condition of the plain ground;

2. Epoxy primer: use one or two layers of epoxy primer with strong permeability and adhesion, with uniform surface and no whitishness, so as to increase the strength and adhesion of the plain ground;

3. Epoxy middle coating: according to the process requirements, add an appropriate amount of quartz sand to the epoxy resin, and evenly coat it with a trowel to several times;

4. Epoxy putty layer: according to the actual needs of the construction of several roads, it is required to be smooth and without holes, and there is no batch of knife marks and polishing marks;

5. Epoxy topcoat: solvent-based epoxy topcoat roller coating two, the overall surface is bright and clean after completion, the color is uniform, and a glossy gold oil can be added to extend the service life;

6. Construction completion: 24 hours before going to work, 72 hours before heavy pressure.