Tengda portable wireless router installation, how to install Tengda router

Updated on technology 2024-08-06
12 answers
  1. Anonymous users2024-02-15

    First, use a network cable to connect the computer network card and the router, set the computer IP address to a network segment with the router, if the router is, then set it to etc., enter the router management interface address in the IE address bar on the computer, and the login prompt appears. After entering, set it up according to the general wireless router setting method (search on the Internet casually).

    After setting, unplug the network cable connected to the computer at one end, plug it into your home adsl cat dialer or community broadband output port), the corresponding dialing settings are set in the wireless router, and the access mode is selected pppoe (adsl) to enter your Internet access and password.

  2. Anonymous users2024-02-14

    1 Connection method: Connect to a portable router with an Internet device (such as ADSL).

    2 Settings: The router has a LAN IP address, change the laptop to a network segment with it, and then enter the LAN address of the router in the browser, and you can log in to set the wireless parameters.

    3. Set the IP address of the mobile phone to be the same as the routing LAN IP segment, subnet mask, and gateway (that is, the LAN IP of the router). I don't know if you're Android or iPhone, it's actually pretty much the same.

    4 ok

  3. Anonymous users2024-02-13

    1.Connect the wireless route to the computer.

    2.The IP address of the network connection on the computer is set to.

    Subnet mask. Gateway DNS

    3. Open IE, enter the user name and password admin

    4. Select the wireless router and set it up. Select PPOE to dial and set the username and password.

    5 In the third step, select Password Settings.

  4. Anonymous users2024-02-12

    The router needs to be set up according to the environment of the Internet, choose the correct way to access the Internet, so that it can access the Internet normally, after setting, both wired and wireless can go to the Internet normally, and the specific setting method of the router is as follows:

  5. Anonymous users2024-02-11

    You'll need to set up your dial-up account in the Near Router. Then you are setting up your SSID and password for unlimited routing. You don't need anything to set up on your phone. You look up this SSID number of yours and then it will ask you to enter the password, and you enter it and you're good to go.

  6. Anonymous users2024-02-10

    How to set up Tengda router?

  7. Anonymous users2024-02-09

    Hello, the installation settings of the Tengda router are as follows:

    2. Then open the browser and enter the management address and login password of the router.

    3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

    6. After the wireless setup is completed, click Save, and then restart the router to use it normally.

  8. Anonymous users2024-02-08

    How should we accurately determine what our router settings are**, we can check the brand on the back of the router, which is marked, and each one will be marked when it leaves the factory.

    After viewing, enter the back of the router on the computer to enter the Tengda router settings page. Log in to your account and password, which is admin by default. to enter.

    If you forget your password, you need to long press the button on your router to reset it. After the reset, you have to re-enter the settings, otherwise your wifi will have no password! end

  9. Anonymous users2024-02-07

    Connect to the router through the cat, connect to the computer through the network cable if there is a wired router, and set the wireless password if it is wireless. Log in to the router settings page or enter the broadband account password, and the computer network connection is set to automatically obtain the IP

  10. Anonymous users2024-02-06

    Set up the wireless router again, does the cat connect the wireless router, do you do this:

    Plug in the wireless router, don't pick up the cat first, reset the wireless router (factory reset), connect the computer to any LAN port of the wireless router, enter the setting page, and set it according to the PPPoE (ADSL virtual dialing) method. Then set the SSID, encryption method, and password. Save, restart.

    After setting up, connect the network cable from the cat to the WAN port of the wireless router.

  11. Anonymous users2024-02-05

    How to set up Tengda router?

  12. Anonymous users2024-02-04

    1. The network cable removed by the modem is connected to the WAN 2 of the router and the computer network cable is connected to any port of the LAN.

    3. The local connection of the computer is set to be obtained automatically, at this time, the general router will assign an address to the computer, 4. If you can't get the address refer to the configuration address on the router manual5. If your computer's real network cable is unplugged, it proves that your network cable is not plugged in well, or your network cable head is not done well, or your router LAN port may be broken or your network card has been loose or damaged, you need to check level by level, don't worry about taking your time.

Related questions
4 answers2024-08-06

If it is a wireless bridging, the model of the two routers must be the same model as well, I have also bridged a lot of routers, in general, TP bridges Tengda's can be, but with Tengda's bridge to other routers, the success rate is not high. First enter your router, then click to turn on WDS, then scan, find your other router, then click to connect, then enter cmd in the run dialog box, and then enter, click OK, if the number can appear, it means that it can be passed. Then enter your path finder, change the IP of the machine to, that is, to separate from the IP address of the router you want to bridge, at this time run in the dialog box, enter ping If it can be passed, it means that the signal of the previous router can be received, and then enter if it is also passed at this time, it means that the bridge is successful, at this time go back to the interface of the router you bridged, take a look at the moving status, if the display is successful, then good luck, this and then turn off the DHCP, and then it's OK, of course, Not all routers can be bridged successfully, some can succeed, some can't, good luck.

12 answers2024-08-06

If the laptop wants to use a wireless network, first of all, there must be a wireless router or a wireless network card to do a soft AP, if you have a wireless router at home is Tengda, you can set up the router according to the following steps, after setting, the laptop can use the wireless network. >>>More

11 answers2024-08-06

Here's how to set up your router:

1. Line connection: >>>More

10 answers2024-08-06

Let me explain to you, the first IP address of this broadband control refers to the range of the device you want to limit the speed of the Internet, such as a computer or mobile phone. Devices that don't want to limit the speed can no longer be within this range. The second item is the direction of the speed limit, whether you want to restrict the device from uploading data, **data, or both.

20 answers2024-08-06

Continue to select "ADSL Virtual Dialing (PPPoE)", then enter the password of your broadband, next, save, and then connect, the IP address appears to indicate that the connection is up, provided that your broadband is normal, if the setting still does not work, then you try to restart the modem and router, and try again. >>>More