Bridging the router, there is a network after the mobile phone is connected, but the computer has no

Your network environment is as follows:

Environment. Is it connected like this?

If so, first of all, you need to know whether the gateway IP address of your secondary router TPLINK is the same as the IP address of the primary router.

If it is on the same network segment, you need to change the gateway IP address of TPLINK to not be the same network segment as the primary router.

Generally, after you change it, as long as your secondary route is disabled DHCP and changed to a different network segment, your primary router LAN port is connected to the LAN of the secondary route, and your secondary router will be used as a switch!

Then your computer can get the IP assigned by the main route DHCP to surf the Internet.

Of course, there is also the network card on your computer, which must also be DHCP assigned IP.

Of course, if you know what the IP is, then say otherwise

Hello, the bridge router needs to change the default gateway of the bridge router, it cannot be the same default gateway, if the default gateway of the bridged return transponder is then the bridge router can not use this address, otherwise only one router can use it, unless the DHCP address pool is restricted, the range of the restricted address pool cannot be the same range, it is best to change the x position to another number, and after changing it, it will also use the changed address to log in to the router.

When we are using a computer, sometimes there is a sudden power outage, and then the electricity is connected but the Internet is not available to produce the cause of this failure is caused by the following reasons:

1. The router is faulty.

The most suspicious is the power supply system, so the first thing that should be checked is the power supply system, to see if the power supply socket has current, whether the voltage is normal, if the power supply is normal, see if the power cord is damaged, whether it is loose, etc., if the power cord is damaged, replace one, if it is loose, plug it back in.

2. Wireless router setting problem.

The wireless router can only connect up to 16 wireless devices, and if there are more, you will not be able to connect, some people can connect to the wifi, and some people can not connect, if someone disconnects the connected wifi, then the original person who cannot connect can be connected, and the number is equal. I checked it in the routing management panel and found that there were exactly 16 connected to wifi, and no more could be connected.

3. Out of the signal range.

This problem usually occurs because the refresh rate is set outside of the frequency range of the display. Beyond the signal coverage, the direct is the distance, and the signal of ordinary routers will become very poor if they exceed ten meters. So when connecting to WiFi, get as close to the source as possible to enhance the WiFi signal.

4. The M address is set to protect it.

It is recommended to check whether the MAC address filtering function (blacklist and whitelist) is enabled on the router, and then restart the router after setting it again. The router MAC address filter setting path is generally as follows: router management interface - wireless settings - MAC address filtering, add your mobile phone MAC address to the allowed MAC address access list or remove it from the prohibited MAC address access list, there may be differences in the settings path of different routers, but the name of the setting item is roughly the same, if you can't find it, please refer to the router manual or consult the customer service of the equipment provider.

After setting up wireless bridging, the secondary router notebook is connected to no network, and the mobile phone is connected to the network.

After setting up wireless bridging, the secondary router notebook is connected to no network, and the mobile phone is connected to the network pro, hello, check the settings of the secondary router. Shut down the DHCP server.

If DHCP is enabled on the secondary router, the computer may obtain the wrong gateway address and cannot access the Internet, so you need to shut down the DHCP server of the secondary router. Setup method: Log in to the management interface of the secondary router, click DHCP Server >> DHCP service, select DHCP server as Inactive, and click Save.

Modify the IP address of the LAN port. If the management IP address of the main and secondary router is the same (take the book as an example), it will cause an IP address conflict, resulting in the computer being unable to access the Internet, so Yu Pai needs to modify the management IP address of the secondary router, I hope my answer will be helpful to you, <>