How to connect the two of the telecom optical modem bridge routers

If you know that the WiFi password has been set by the modem and the router has a bridging function (WDS), then do the following:

1. Log in to the wireless router management interface (generally use IP address such as login), find WDS in the wireless network settings, and select enable or enable;

3. If the login address of the wireless modem is, you can change the IP address of the wireless router to or other than the IP address, as long as it is different from the IP address of the wireless optical modem. The disadvantage of this approach is that the mobile device needs to reconnect between the coverage areas of the two devices.

4. If the login IP address of the wireless modem is, you can set the IP address of the wireless router to and change the IP address pool (set in the LAN port parameters) to change it, so that there will be no IP conflict with the wireless modem.

Telecom modem settings.

1.First, log in to the Telecom Optical Modem Router.

2.Set the SSID number and Channel in Wireless Settings - Basic Settings, and set the fixed channel number.

3.Set the wireless signal encryption information in the Wireless Settings - Wireless Security Settings to record the SSID, channel, and encryption settings of the wireless router after setting.

Wireless router settings.

1.Log in to the wireless router that needs to be bridged.

2.In the network parameters - LAN port setting, change the IP address to be different from the first router (to prevent IP address conflicts), for example, save, the router will automatically restart.

4.Select the SSID number of the first router in the list of scanned signals and click "Connect".

5.Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, and click "Save".

6.Shut down the DHCP server. In the DHCP server, select Disable, save, and restart the router.

7.In this case, the WDS has been successfully established between the modem and the wireless router.

A wireless router is required to have a bridging function. Taking the TP-Link router as an example, perform the following steps:

1. First, log in to the background management address of the router on the browser and enter the background management page;

2. After entering the router background management page, you can see the "Application Management" function on the main page, click to enter;

3. Find the "Wireless Bridge" function in the application management page and click to enter;

4. Then click "Start Setup";

5. Then select the WiFi signal of the modem on the WiFi connection page to connect;

6. After selecting the WiFi of the modem, you need to enter the WiFi password of the modem, the purpose is to connect the wireless router with the network of the modem;

7. After connecting, the window will pop up to set the wifi name and password of the wireless router, and you can set the wifi of the wireless router by yourself in this window.

Here's how:

2. Jump to the home page of the terminal and enter the password to log in.

3. After logging in, select "Network" on the home page, and then enter the network settings page.

4. Click "Broadband Configuration" to set up broadband Internet access. You can see that the initial settings bar is grayed out and cannot be set.

5. Right-click in the blank space, select "Review Element", and then click "Open Console".

6. CTRL+F: Search for "mode" to find the corresponding ** Dai Pi Zhen sail code, and the corresponding ** line to find the network mode modification item frm mode: modify "disabled" to "abled" so that the network mode can be modified.

7. Mode: Hail can be modified to bridge mode, save and exit.

8. Click the networking icon in the lower right corner of the desktop, and then open the network settings.

9. Select "Dial".

10. Click Set up a new connection, then select Connect to Luling Internet, and finally click Next.

11. Select Set up a new connection.

12. Select Broadband (PPPoE)(R) and continue.

13. Fill in the broadband and password provided by the operator, and check "Allow others to use this connection" according to personal needs. Finally click on Connect.

14. After the connection is successful, the newly created broadband connection will be displayed.

1. First open the browser and log in to the router with the new management IP.

2. Go to the basic settings of the wireless settings and turn on the WDS function.

3. Then you need to click the scan option to scan the wireless signal.

4. Connect the wireless signal of the modem, the channel number here should be the same as that of the modem, and enter the corresponding wireless password.

5. Back to the running status page, when the WDS status you see is successful, you can basically go online.

First of all, the optical modem and the router must have a wireless bridging function.

The optical modem has a wireless signal to emit.

If the router interface has a bridge function, you can directly click in and fill in the wireless name and password sent by the optical modem.

How to set up the router when in bridge mode!

The main advantage of using routers to dial-up Internet access is that it can improve the stability, coverage, and capacity of the home network. After the fiber-optic modem is changed to bridging, the fiber-optic modem is responsible for the conversion of photoelectric signals and interface protocols, and is no longer responsible for the routing function, which reduces the pressure on the processor of the fiber-optic modem and improves the stability. If the user chooses a mid-to-high-end router with good stability, its processor performance far exceeds the performance of the fiber optic cat processor, which is conducive to the stability of the home network, the maximum transmission performance and the number of devices (in layman's terms, it is the maximum number of devices that can be wirelessly connected).

Of course, there are good and bad parts of any problem, and some areas may also restrict the fiber modem from being set up as a bridge to do targeted speed reduction, which depends on the actual situation.

Some of today's optical modems have routing functions (such as individual households), while others do not have routing functions (such as work offices).

For home modems, they generally have routing functions, but the Wi-Fi signal strength provided is quite different. I will talk about the use of the two optical cats I have used. It turns out that with a mobile optical modem, there is no problem in the room with the optical modem, but in the next hall it seems that the signal is much weaker, and you must use a router to bridge the optical modem to use the wifi Internet normally.

Later, I lived in another place, switched to the optical modem of Telecom, and all rooms can use wifi Internet access normally, and there is no need to add another router.

From the above situation, it can be seen that if the wifi signal provided by the modem is strong enough, there is no need to add a router (if a router is added, there may be some delay); If the WiFi signal provided by the modem is not strong enough, in order to use the WiFi Internet access normally, a router must be added to bridge the modem.

The advantage of adding a router is that it increases the interface of the wired output, which can be considered for those who have this requirement.

The main purpose is to make the network more stable, because the most stable is the wired connection, and although wireless is convenient, it will be affected by the interference of the whole environment.

The advantage of the optical modem bridging mode is that the installation of network cables is omitted, and there is no need to lay network cable lines, and wireless connection. Using your own router is a stronger wifi signal.

Optical modem, also known as single-port optical transceiver, is a three-piece optical fiber transmission equipment developed for special user environments. The device adopts a large-scale integrated chip, simple circuit, low power consumption, high reliability, complete alarm status indication and perfect network management function.

How to bury the bridge wiring of the optical modem router:

1. First of all, the first simple orange login is the nameplate information on the back of the optical modem, and enter the super administrator password after logging in.

2. After entering the modem, find the network settings tab, click on the network settings, and then find the 41-channel connection under the new connection, delete the connection, you can see that the 41-channel connection is a dial-up connection, because there is a password under this connection.

3. After the split group is deleted, you need to establish a bridge connection to transfer the dial-up information to the wireless router through the bridge connection, click New Connection, write the bridge connection with the connection name, and then write the bridge 41 channel, so write 41 on the VLAN ID, so that the optical modem is set up.

4. Wireless router settings, if the router is already another network segment, it is not necessary, if not, you need to set the network segment of the wireless router to an unexpected such as1 etc., to avoid conflicts between the two routers.

5. Set the router to find the PPPoE dial-up option, enter the dial-up in the modem, click Save, and connect a network cable from any network port (except ITV port) to the WAN port of the router, so that a bridge is formed between the modem and the router, and the modem converts the optical signal, and then the router dials the number.

After the ADSL broadband at home is upgraded to the optical fiber network for free, and the operator installs the optical modem with the wireless router function, how to carry out wireless bridging and how to set it up so that there will be no conflict? How to set up wireless bridging between a wireless router and an optical modem so that there is no conflict? Follow me to see how to set it up.

1.Enter the modem management interface, or view the management IP from the back of the modem, and the management address of Huawei ZTE's modem is the same.

In order to avoid conflicts. First, log in to the management interface of the wireless router and change the IP address of the LAN port to another IP address in the same network segment, for example:

The advantage of this is that it is more convenient to manage in the future. After saving, the router needs to be restarted.

2.After the router is restarted, open the browser again, open the management interface with the new LAN port IP, and log in.

3.Go to Wireless Settings - Basic Settings of the wireless router, find Enable WDS under Basic Parameters, and check this item.

5.After a while, the information list of the scanned AP came out, and the corresponding optical modem at home was found in the list'WiFi signal name.

Note the information about the channel and encryption type, and then click Connect.

6.After clicking Connect, the information of the modem to be bridged, such as SSID bssid, will be automatically filled in. It should be noted here that the upper channel and the lower key type should be set to be the same as those of the modem, and then enter the corresponding password and save it.

7.After saving, we return to the running state, and the WDS state in the wireless state, after initialization, turns to Success. Indicates that the bridging between the wireless router and the optical modem is successfully completed.

8.After the above settings, the basic operation is completed, but for the convenience of use, the DHCP server also needs to be set up, our goal is to turn the wireless router into an AP, and the initiative of network management is still handed over to the optical modem, without the need to use the wireless router to allocate IP.