What should I do if the headphone mode keeps showing after the iPhone gets into the water?

First turn it off, treat the residual water, and then use a cotton swab to clean up the headphone jack. Blow with a hair dryer if you can. It can also be sunbathed. Putting it in the rice for dozens of minutes can also absorb moisture. Finally, boot it up and test it.

It should be caused by the water in your mobile phone is not completely dry, and it is recommended to deal with it as follows after the mobile phone gets into the water:

1.Shutdown: This is definitely the first step to save the phone, no matter how much water ingress the phone, please turn it off first, otherwise it will burn out the circuit directly.

2.Check the location of water ingress: In most cases, the location of a large amount of water ingress into the mobile phone is generally the headphone jack and charging hole, because as long as it is not broken in other places, there are no cracks.

3.Check for external damage: if it's simply soaked in water, it's not a big problem. However, if it rains and falls out, check whether there is any cracks in the phone and water in.

4.Simple water intake: If it is just a simple water intake, then take a hair dryer, adjust to the cool breeze setting, and dry it with a small breeze. Since most of the water enters from the headphone jack, the phone should stand up.

5.Wait a few days before turning it on: When the phone is dried, it can be turned on and used normally, of course, if it can't be turned on, it can only be that the water enters too much, and the circuit inside is broken. It should be sent for repair in time.

I'll tell you a dirt way. Turn off your phone and put it in your rice pocket. 24 hours later. Charge your phone and take it out. After turning on the phone, try again, and you can basically solve this problem.

First, clean up the water stains, then turn off the phone and restart it to see if the headphone mode can be removed.

2. Restore your phone to factory mode, take iPhone 6 as an example, the specific method is as follows:

1. First click "Settings" on the desktop of your iPhone 6 phone.

2. Select the "General" option after entering.

3. Then find the "Restore" item and click to enter.

4. Click "Reset All Settings" after entering.

3. If you still can't cancel the earphone mode after restoring the factory settings, you can bring your phone and warranty card to the official repair center of the Apple mobile phone for repair.

If the headphone mode is displayed after the Apple headphone jack is flooded, turn off the phone, find a needle, and gently poke the earphone hole, it may be when the earbuds are unplugged. The bouncing device inside did not return to its original position.

Swirl the headphone jack with a cotton swab to wipe the inner wall clean.

Turn off your phone and restart it to factory settings.

Even if it is the headphone mode that appears after entering the water, then use a hair dryer to blow for ten minutes, if it is not solved, then it can only be repaired, and there is no other way to solve it.

When you don't know the specific solution, you can call Apple customer service to tell him what the situation of your mobile phone is, and then ask him to tell you the specific place in your city, in order to repair your mobile phone faster, click on the avatar to learn more.

When the tablet is flooded with water, the headphone mode appears, first dry the water on the surface of the earphone jack with a cotton swab.

2.Then put it in a ventilated place to dry for a few days to see if the headphone mode of the tablet can disappear.

3.It should be that the micro switch in the headphone jack is broken by water entering the tablet headphone jack, and it becomes the headphone mode.

4.If it still doesn't work, you should take it to the after-sales outlet for a professional to test it, repair or replace the new headphone jack, etc.

1.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

2.Wipe down the circuit board with anhydrous alcohol and try to turn it on.

Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

3.Send it to the repair center for repair as soon as possible (0755-23945679). If the motherboard is severely corroded over time, it will cause irreparable consequences.

After the headphone jack is flooded, the headphone mode is displayed, which should be caused by a short circuit.

After the headphone hole enters the water, the headphone mode is displayed, it should be shorted, because the water is a conductor, resulting in the headset electrocution shorted, so the headphone mode will be displayed, the solution can try to shake the phone hard, and then you can use the headphone head back and forth to insert the headphone hole several times to try, maybe a small amount of water will be brought out, if it is a motherboard problem, it is recommended to send it directly for repair, because there are many problems with the mobile phone in the water, or it is better to clean it as a whole.

Personally, it is suggested that the problem of water entering the mobile phone may not appear immediately in a short time, and the problem will appear after the water traces corrode the components on the mobile phone motherboard, so take advantage of the problem just out of the station, solve it immediately, and you can reduce the loss.

The Apple phone shows how to adjust the headphone mode back.

1. It may be that the micro switch of the headphone jack fails, or the headphone jack may be damp and water, or there may be foreign objects that cause the headphone mode;

2. If you have been paired with Bluetooth headsets or speakers before, it may be that the Apple phone is automatically matched with Bluetooth headsets or speakers, and you can turn off Bluetooth in the control center;

3. Use a cotton swab dipped in alcohol to rotate and wipe the headphone plug and mobile phone jack (the plug or jack may be oxidized) to try it;

4. Use the headphones to access the interface, turn on the iPod to listen**, then press pause, press the home button to return, turn off the iPhone (without using other third-party software) to pull out the headphones, and then turn on the headphones;

5. If you don't succeed in trying a few more times, if it still doesn't work, hard restart the Apple phone, and when the white apple appears, pull out the earphone to cancel the earphone mode;

Completely crash forced restart method: Press and hold the home button + lock screen button at the same time until the phone restarts; The new full-screen iPhone phone reboots by pressing and holding the power button and volume down button of the Apple iPhone X at the same time while the device is turned on, and selecting Power Off in the screen options;

Take the mobile phone and shake the water from the earphone jack out, and just shake the water clean and dry.

If the earphones of the Apple mobile phone enter the water and change to the earphone mode, then you can change to a new earphone.