The watch hands are off, how should I repair them?

When the watch is subjected to severe vibrations, the hands may fall off, especially the second hand. If the second hand (including the small seconds or other hands) has fallen off and may get stuck between the hours, minutes and the dial, the second hand will be plucked and scratched against the dial if the watch continues to move, causing scratches to the dial. If you find that the watch hands are displaced or fall off, you must stop the watch immediately, and if there is no stop second device, you must also pull out the watch handle to let the watch gradually stop.

Chengdu Famous Watch Repair Center: Room 05, 24th Floor, SAC Sichuan Aviation Plaza, No. 6 Renmin East Road, Jinjiang District, Chengdu.

With the concept of quality assurance and integrity management, all employees have been professionally trained, with excellent technology and rich experience, to better serve merchants and customers, we adhere to the tenet of "customer first, attentive service, integrity management", 24-hour service**: 4000-562678

The customer service center is equipped with professional letters, answering **, understanding customer needs and answering questions, and your satisfaction with our service will be our honor.

If the pointer falls, you only need to save the original accessories and take them to stick. Moreover, Rolex also has maintenance points in China, you can check the professional maintenance organization, and then choose to send it for repair nearby.

The watch is broken, and the back cover has been taken off, in fact, there is no problem, although the hands are not gone, but they can also be repaired, it is recommended that you go to some professional business second, or a professional place to repair the watch to repair it.

In fact, this is a very simple thing, as long as you do it yourself, many people seem to love the format of the watch very much, in fact, he did not make any movements, so you should try to put this is a if the watch is put away, then of course it is better, in fact, to some professional departments to repair, it is obvious that the success rate will be higher, which should be noted.

1.Take it directly to the store for repair There is no problem with the outside of the watch, but the watch just doesn't go, you can take it to a professional repair shop, and let the staff inside help you repair it, generally they can tell you more accurately the damaged layer and the way to repair.

2.Replace the mirror If it is caused by the damage of the mirror, you must replace the mirror first, and clean up the internal debris by the way. This method can directly get the watch.

3.Winding up Generally speaking, there is a very common factor for mechanical watches not to go, and that is lack of power. Usually everyone just needs to pass.

If the watch stops due to a collision, it is likely that the internal movement or pinion will be rubbed and it will not function properly. As a result, the watch will not be able to move.

Because the parts inside the watch are very small and very precise. After falling, the pointer does not go, this one must be taken to the repair master ** to repair, individuals must not think about dismantling, because once disassembled, it cannot be installed.

Hello, judging from your description, the watch fell more seriously, and it is recommended that you apply for after-sales maintenance directly. If this kind of man-made damage is made, you may have to pay a large part of the money.

If the ** of the watch you buy is relatively expensive, you can get it to the after-sales service to repair, if it is a watch for dozens of dollars and hundreds of dollars, there is no need to buy another one.

After the watch falls, don't try to repair it yourself, we don't understand anything, it will only get worse and worse, just find a professional watch repair master to repair it.

After the watch was broken, the back case took off the hands and did not go, which is most likely due to the broken gear inside. In this case, the watch needs to be disassembled for further repair, so it is necessary to go to a professional watch shop for repair.

You can take it to a professional repair shop and let the staff inside help you repair it, and they can generally tell you more accurately the damaged layer and the way to repair it.

If the watch falls to the ground, there is a problem with the stabilizer inside the watch, so that the hands are not gone, so it is recommended to go to a watch repair shop in the mall to repair it.

The watch falls, the rear case comes off, and the hands do not go, so you have to get the after-sales maintenance in time and let the maintenance staff help you repair the watch, so don't worry.

There is nothing wrong with the outside of the watch, but if the watch just doesn't go, it is recommended that you bring the watch to the after-sales center to detect the specific cause of the failure, so as to avoid your normal use.

Hello, in this case, go to the watch shop and ask them to help repair it, if the watch is more expensive, then go to the repair shop or go to the specialty store to have a look.

After the finger watch falls, the case is off, the hands do not go, you can only go to a regular watch store to repair it, see if there is any value of repair, if not, you can change a new watch.

Take it to the repair office, let the repairer do an appraisal first, if there is value to repair, repair, if there is no value to repair, send it to the repairer as accessories.

If the watch is broken, the watch can be taken off, and the hands do not go, it is recommended that you send the watch back to the after-sales service for repair.

The watch was violently vibrate, resulting in the movement parts inside may have fallen off, and the watch needs to be tested and repaired after sale.

After the watch is dropped, if some of the small parts inside are not broken, you can go to the kind of watch repairer to give it a try.

Go to repair, you can't repair it, it's not expensive, just buy a new watch.

If you have a broken watch, you can go to a specialized watch repair shop to repair it.

If it doesn't work, buy another one.

There is no problem with the outside of the watch, but the watch just doesn't go, you can take it to a professional repair shop, let the staff inside help you repair it, generally they can tell you more accurately the damaged layer and the way to repair.

For this kind of watch falls, the rear case falls off, and the hands do not go, it is recommended to go to a watch repair shop or after-sales service to repair.

If the watch falls, the case comes off after the case, and the hands don't go, you can check it up and down to see how to repair it, or ask customer service.

The watch hands are deformed:

First of all, the hundred watch crown should be pulled out in time to stop the movement to prevent the hands from scratching the watch, dial or damaging the dial.

Secondly, after pulling out the crown, please repair it in time to avoid the dust of the watch from entering.

Third, if the degree is a hollow watch, try to avoid the small hands falling into the back of the dial.

Fourth, when installing both hands, pay attention to choosing a formal mechanism to prevent scratching the improper operation of the dial plate, resulting in a decrease in the waterproof performance of the watch.

In general, maintenance is relatively easy if there is no damage to the inside of the watch. If the wheel tube is deformed, broken, or the parts are worn, the repair will be slightly more difficult. Please note that watches with hands need to undergo a full water resistance test, and the water resistance ring will need to be replaced when it ages. Right.

When the watch is worn and used daily, it is easy for the watch hands to fall off when it is impacted. Since the hands are installed in layers, and the top tube is connected to the second hand, the second hand is usually lost.

Watch hands fall off need attention:

1. Avoid moving the watch, so that the hands scratch the dial or the hands are damaged.

2. For some hollow watches, try to avoid the small needle falling behind the dial.

3. After the crown of the watch is pulled out, it should be repaired in time to prevent the watch from entering the dust and damaging the movement.

If the needle on your watch falls out, there are a few ways you can consider fixing it:1. Retrieve the needle and reinstall it: If you are able to find the needle that fell out, you can try to reinsert the needle back into the correct place using a small tool such as a needle tip or small clip.

Be careful, make sure the needle is properly aligned with the shaft hole, and gently push the needle in. 2Ask a professional repairer to repair it: If you are not sure how to repair it or cannot find the dropped needle, it is recommended that you send your watch to a professional watch repair shop or brand repair center.

They have experienced and professional tools that can fix the needle on the watch and ask which question. 3 Replace the entire needle assembly: If the needle on the watch cannot be retrieved or is badly damaged, the entire needle assembly may need to be replaced.

This will need to be carried out by a professional repairer who will replace the needle assembly with a brand new one that fits your watch model.

If the watch hand is lost or damaged, it can be replaced, so please don't worry too much. Since the pointer is installed in layers, it is the most accommodating.

The upper tube is connected to the second hand, so it is usually the second hand that falls off. The crown should be pulled out in time to stop moving, so as to avoid the watch from moving around, so that the hands can scratch the dial or the hands will be damaged; For some hollowed-out watches, try to avoid the small needle falling behind the dial; After the crown of the watch is pulled out, it should be repaired in time to prevent the watch from entering the dust and damaging the movement. If the wheel tube is deformed, broken, or the parts are worn, the repair is slightly more difficult.

Unscrew the back cover of the watch, pull out the handle (the barrel of the clockwork and the handle for adjusting the time), take out the watch core, use the pointed tweezers to take the watch against the axis and put it in, gently tap the axis with the back handle of the tweezers, put it into the handle and rotate it to see if the three needles interfere, and then put it into the case and try to see if the watch hand interferes with the glass surface, if there is no interference, the installation is successful, and the dust is blown off with an ear wash ball and screwed on the back cover.

It's a clock.

The work of the bai craftsman.

Unscrew the back cover of the watch, pull out the self-stemmed handle (in the handle of the clockwork and the time-adjusting dao), take out the watch core, allow the watch to be placed on the axis with pointed tweezers, gently tap the shaft with the back handle of the tweezers, load the tap handle and rotate to see if the three needles interfere, and then put it into the case and try to see if the watch needle interferes with the glass surface, if there is no interference, the installation is successful, and the dust is blown off with an ear wash ball and screwed on the back cover.

If you don't have hands-on ability, you should ask a professional to deal with it.

Go to a watch repair shop and they'll take it apart and put it on for you, and it won't spoil the original look, which happened with my previous watch.

If you just drop it, you will find a watch seller, if you buy it for a long time, you will find a watch repairer, and occasionally the watch seller will be the same person who repairs the watch.

Watch hands fall off: When the watch shakes violently, the hands may fall off, especially the second hand.

Expert. If the second hand (including the small seconds hand or its other function) falls off, it may become stuck between the time, minute and dial. If the watch continues to move, it will move the second hand and rub against the surface of the dial, causing scratches to appear on the dial.

Of course, it's even worse if you dial the pin at this point, you know, the value of the pin is high, and there are accessories that are not easy to find.

It is recommended that you open the warranty source that was attached to the purchase of the watch.

Under normal circumstances, there will be a DU service address on the warranty link, or find a regular watch service center for inspection.

Did you fall if you didn't come? What should I pay attention to when the second hand of the watch is lost? Avoid moving the watch around, allowing the hands to scratch the dial or damage the hands; For some DAO hollowed-out watches, try to avoid the small needle falling behind the dial; After the crown of the watch is pulled out, it should be repaired in time to prevent the watch from entering the dust and damaging the movement.

Pay attention to the selection of a regular mechanism to prevent scratching the dial and reducing the waterproof performance of the watch. When installing the watch hands, a thin film is placed on the dial to protect the dial. After installing the watch hands, a comprehensive waterproof test is required, and the waterproof ring needs to be replaced again if it is aging.

It's best to take it to a watch repairer.