Is it okay to blow the Apple phone battery with a hair dryer if you can t take it off

Yes, Apple mobile phones have built-in batteries, and you can only disassemble them if you want to remove the battery.

Take iPhone 6 as an example.

1. After shutting down, use the corresponding screws to remove the two screws at the bottom.

2. Because iphone6 adopts an integrated design, the screen is embedded in, so you need to use a suction cup to suck the screen, and you can use a pry blade to pry out the screen by sucking a gap, and pry up little by little around the screen starting from the home button.

The screen part is still connected to the fuselage at this time, and it can be upright at most 90 degrees and not exceed this angle.

3. Find and unscrew the screws that fix the screen connection. When removing the battery, it is best to remove the screen first, as the battery is fixed with glue and it is very laborious to remove. Unscrew the screws on the protective cover, and then remove the protective cover as well.

4. Disassemble the connector of the screen. There are several connectors between the screen and the body, and you can pick them out of the port with a small pick or a thin nail file.

5. Remove the protective cover of the battery connector. The battery connector cover is secured by two screws, unscrew them off, and then remove the metal cover as well.

6. Disassemble the battery connector. There is only one connector between the battery and the circuit board, which you can pick apart with a small pick or a thin nail file.

7. Use a hair dryer.

Heat the back cover and blow the glue soft. iphone 6

A lot of glue is used to hold the batteries in place, and they need to soften to get the batteries off. You can use a hair dryer to heat the back cover of your phone to soften the glue. Do not use a heater that is hotter than this, and hold the phone comfortably in your hand while heating.

8. Use a credit card or plastic paddle to pry the battery open. You can use a bank card, thin paddle or pry the battery at the bottom little by little. Avoid the top part near the screen connector, as there is also a connector hidden underneath.

Also, don't use mobile phone parts as a fulcrum for prying the battery. Try to stick the glue to the case so you can reuse it later.

9. Connect the new battery and fold off the connector. If you don't have much glue left, you can use ultra-thin double-sided tape.

to fix the new battery. The connector only needs a little force to get back into the slot, but aligning the position can be a bit cumbersome and will take some time. The original battery connector was folded down, so now it's the same, and it can be pressed down with a small pick or a thin metal file.

It can be seen that the disassembly of the iPhone and the removal of the battery require courage and carefulness, and the battery here is damaged, which may be accidentally short-circuited during the disassembly process, or the connector is torn.

It must not be blown dry, it may blow water into the inside of the phone, so you should immediately put desiccant or rice in the sealed bag, and then put it in the phone to absorb moisture. And it's best not to use your phone during this time.

If your mobile phone is flooded with water or liquid, it is recommended that you do not try to turn it on to prevent damage to the internal components due to a short circuit inside the machine (if the machine battery is removable, it is recommended to remove the battery).

It is recommended that you bring the machine to the local after-sales service center, and the engineer will help you test, and the specific cost is subject to the test results of the service center.

As long as you are sure that the water is indeed blown dry, there is no problem, and it is best to put it in the refrigerator for another day to ensure that the water evaporates.

First of all, don't turn it on again, if you can take out the battery, take out the battery, blow it with a hair dryer, bask in the sun, and dry it after a few days Try to turn it on.

Dry it slowly, the hair dryer is hot, I'm afraid of danger.

Don't blow the motherboard on the hair dryer, you take out the battery and put it in a ventilated place for a few days.

It is better to put it in a rice bowl to absorb water and then take it out.

1 Water ingress and crashing are the two major taboos in the use of mobile phones, and water ingress of mobile phones is particularly serious. According to an engineer from Guoxin, after the mobile phone gets into the water, the first thing to do is to turn off the power, of course, not to press the shutdown button, but to remove the battery. Because as soon as you press the shutdown button, the mobile phone will be powered on, and it is likely that a short circuit will occur, causing damage to the mobile phone, and then send it for repair as soon as possible.

If your phone's warranty has expired and you don't want to send it for repair, you can boldly take it apart! Wipe the parts of the phone with a tissue, and then blow it with a hair dryer for a few minutes, in order to ensure that all the internal parts are dry, it is advisable to air dry the phone for a few more days before you can turn it on again.

2 Once the mobile phone gets into water, remove the battery immediately, and do not turn it on immediately to understand the condition of the mobile phone. After removing the battery, do not use a hair dryer to deal with it, and immediately send it to the repair professional to disassemble the machine for water treatment, such as falling into sewage or corrosive liquid, and use ultrasonic cleaning and drying before proceeding to the next step of maintenance. If the mobile phone can still be used after water penetration, it should be sent to a professional to deal with it to avoid corrosion of the circuit board and make it impossible to repair.

3 No matter what kind of water the phone falls into, you should remove the phone battery first and no longer power the phone. If it falls into clean water, remove the battery and clean the phone with anhydrous alcohol, because the alcohol volatilizes quickly, and the water on the circuit board can be volatilized together. Then use a heat gun or hair dryer to dry the circuit board, and then power up the test machine, and most mobile phones will work normally.

If it falls into the sewage, it should be cleaned immediately, and the dirt that can be seen should be cleaned first. Use a brush to brush off the impurities attached to the pins of the components. Then, the circuit board is scrubbed with an alcohol cotton ball, and if the pollution is serious, the impurities must be vibrated out with the help of an ultrasonic washing instrument.

Then use an air gun to dry the circuit board, and then repair all the chips.

Once the mobile phone gets into the water, the battery should be removed immediately, and it must not be turned on immediately to understand the condition of the mobile phone. After removing the battery, do not use a hair dryer to deal with it, and immediately send it to the repair professional to disassemble the machine for water treatment, such as falling into sewage or corrosive liquid, and use ultrasonic cleaning and drying before proceeding to the next step of maintenance. If the mobile phone can still be used after water penetration, it should be sent to a professional to deal with it to avoid corrosion of the circuit board and make it impossible to repair.

Don't use a hair dryer after your phone falls into the water, this is the right way, it's so practical!

When I wasn't a smart phone before, I put it under an incandescent desk lamp to dry, and it didn't break.

If you are using a Huawei phone, we recommend that you do the following:

1. Please try to place your phone in a dry and ventilated place and use a paper towel to blot the water stains on the surface of your phone.

2. If the phone is turned on, press the power button to turn it off; If your phone is turned off, don't try to turn it on.

3. Please take out the SIM card and microSD card.

4. Take your phone to a Huawei customer service center as soon as possible to avoid unnecessary losses.

Precautions: 1. Do not move or shake the mobile phone frequently after entering the water, so as to avoid the spread of moisture inside the mobile phone.

2. Do not bake with a hair dryer or stove after entering the water, so as to avoid the liquid being blown into the inside of the mobile phone and damaging the mobile phone at high temperature.

3. Some mobile phones can be turned on and used normally after simple treatment, but the mobile phone is composed of precision electronic components, and there is a hidden risk after water ingress, so it is recommended not to try to turn it on.

4. During the after-sales maintenance process, data may be lost.

Quickly disassemble the phone, take out the battery, and then blow it with a hair dryer, don't get too close.

Yes, but if you want to take the battery off directly, I will fall into the water for a long time.

If the iphone6 battery is punctured when it is disassembled, it can continue to be disassembled, and replace it with a battery of the same specification after disassembly.

Prepare materials: screwdriver, batteries.

1. After turning off the phone, use a 5-corner screwdriver to remove the two small screws at the bottom of the phone.

2. With the help of suction cups and warps, pull up the mobile phone screen.

3. The screen in the top area is arranged, so after prying the screen open, you need to pay attention.

4. Unscrew the five small screws that lock the cable.

5. Use a warping rod to remove the 4 cables.

6. After separating the screen, you need to remove the battery cable first, and then remove the old battery with the help of a spudger.

7. After cleaning the double-sided tape at the bottom of the battery compartment, prepare to put on a new battery.

8. Paste double-sided tape and install the battery cable.

9. Then install and fix the 4 cables of the screen in turn, and turn on the verification.

It's all striped underneath? Are you talking about a broken battery skin? Or is the battery heart broken?

Still the battery strip didn't come down!! Either way? As long as you want to continue dismantling, you can still continue, big deal, change the battery,!!

If the battery is swollen, or the inside is damaged, remember to replace the battery, because it is not safe!

What battery? It's a lithium battery that can smoke, right? Smoke means that the inside has been short-circuited, the energy is being released, and after the energy is released, it will be okay to dismantle it again, but it will be safe. If you are not a technician, it is better not to disassemble it yourself, the battery is poisoned.

The battery glue is really not easy to pull.

The safest way is: after disassembling the phone, there are two black stickers under the bottom of the battery, which can be slowly uncovered, and slowly pull out with your hands after uncovering, at this time, don't continue to pull out the white glue, but use a small screwdriver, roll up the white tape, slowly pull it out, pull a little roll a little, pull a little roll a little roll, and slowly roll out the whole tape.

No, because the glue melts when exposed to heat, and the glue is solidified at normal room temperature, and it is difficult to remove it.

The so-called non-removable battery is not that it cannot be disassembled, but that it cannot be simply opened and replaced directly. Apple phones have built-in batteries, and if you want to take them off, you can only disassemble them. The apple is connected by screws, and if you disassemble the screws, you can remove the back cover, but you have to carefully pull out the battery cable, and then you can replace the battery.

OK. Basic information of iPhone:

iPhone is a series of smartphones developed by Apple, which is equipped with the iOS mobile phone operating system developed by Apple. The first-generation iPhone was released on January 9, 2007 by Steve Jobs, then CEO of Apple, and officially went on sale on June 29 of the same year.

The seventh-generation iPhone 5S and iPhone 5C were released on September 10, 2013, and officially went on sale on September 20 of the same year. The eighth-generation iPhone 6 and iPhone 6 Plus were released on September 10, 2014. At 1 a.m. on September 10, 2015, Apple will hold its 2015 autumn conference and release three different models of new iPhones, namely iPhone 6S and iPhone 6S Plus.

At 1 a.m. on March 21, 2016, Apple held its 2016 spring conference and announced the iPhone SE instead of the iPhone 6C as stated on the Internet.

The iPhone 7 was unveiled at the 2016 Apple Fall New Product Launch Conference at the Bill Graham Municipal Auditorium in San Francisco, USA at 1 a.m. Beijing time on September 8, 2016.

On November 25, 2016, Apple updated the warranty policy of the iPhone in China on its official website, and it will no longer be repaired by replacement.

On March 21, 2017, Apple launched a special edition iPhone 7 and iPhone 7 Plus with a beautiful red appearance, with a starting price** of 6188 yuan.

On September 13, 2017, Apple launched a new generation of products, iPhone 8 and iPhone 8 Plus, iPhone X and iPhone X Plus.

It's better to buckle the battery before blowing, as for the tools I guess you don't.

It is best to put it in the raw rice for 12 hours to absorb all the moisture.

It's best to go to the place where the phone is repaired to check it, and it shouldn't be wrong right away in the short term.