The correct way to paste the car film, how to paste the car film Detailed explanation of the car fil

Cut the car film and use the film tool to stick the car model on the car.

The specific steps are as follows:

1. Before the film, first of all, we must ensure that the working environment meets the requirements of dryness and less dust, otherwise the dust and debris will enter during work, which will affect the effect of the film. It is recommended to wash the car before applying the film.

2. Cover the necessary position of the vehicle, and protect the interior and exterior with a protective cover, if there is no special material, you can also choose plastic wrap.

3. Clean the car glass that needs to be filmed, pay attention to the top and edge of the glass, and then wipe the water.

4. The next step is to cut the car film, pay attention to the size of the car film to match the glass. Spray a little water on the surface of the glass, then adsorb a certain thickness of plastic film to the window, and then draw a pattern according to the edges, the template can be a little more than the glass.

5. When the front and rear windshields are filmed, the baking film also needs to be shaped. Cover the cut car film on the outside of the glass, and then use the heat gun to shape it, this step is also more critical, and it is easy to make mistakes, because the temperature and shaping method of the heat gun have relatively high requirements, otherwise improper use can easily lead to the car film blackening or glass cracking.

6. After the baking film is completed, you can officially paste the film, spray the inner glass with water or window film installation liquid, and then tear off the innermost layer of plastic film from the car film, and then paste the car film to the inner glass and move it to the most suitable position.

7. Spray some water or window film installation liquid on the surface of the car film, and then use the Yangtze River Delta plastic scraper to catch water.

8. After the water is completed, check whether there are bubbles between the car film and the glass, whether it is firmly pasted, whether there are wrinkles, whether there are scratches, etc., if there is no problem, finally clean the water on the edge of the glass with a towel.

If the window is opened shortly after the film is applied, it is likely that the film will shift because the film is not completely dry between the film and the glass, so it has not yet reached a firm position. Therefore, it should be noted that within a week (7 days at the earliest, 15 days at the maximum), do not raise or lower the windows, wipe the inside of the windows, or hang objects within a week after the vehicle glass film is filmed.

The correct application of the car film is 5 steps:Car washing, measuring size, filming, shaping, checking for air bubbles.

Car washing: Before giving the car film, you need to wash the glass, because if the car glass is not cleaned, the car film will be blurred, which will not only affect the appearance, but also affect the quality of the car film, cleaning the glass is very simple, wash with water, and then wipe it repeatedly with a dry rag, in order to wash it clean, it is best to wash it several times.

Size: according to the size of the window to cut the car film, cutting film is an important process of car film, the size of the cutting car film is generally determined by the specific size of the window, the size of the cut is slightly larger than the size of the window.

Filming: Cut the film into an appropriate size and cover the outside of the glass, and use a scraper to adhere to the film for shaping.

Stereotype: When cutting the film, the staff sprays soapy water on the window glass of the car, which is to better paste the car film, and uncover the paste layer of the car film after shaping, the car film must be carefully pasted inside the window, and the distance between the film and the edge of the window is adjusted under the lubrication of soapy water, in order to ensure the overall appearance.

Check whether there are air bubbles: After completing the above steps, carry out the final inspection, such as whether there are air bubbles, etc., if there is no problem after the inspection, then the car film is pasted.

What is the role of car wraps?

Car film is applied to car glass to control sunlight and ensure safety. In addition to sunlight control, its basic safety features include clarity, anti-glare, UV protection, heat insulation, scratch resistance, sticking to glass shards, adequate shelf life and privacy protection, and performance to ensure safe driving.

7.Drying: After pasting the car film, you need to wait for a period of time for the glue to dry the cover quietly, generally about 24 hours.

2.When applying the film, it is necessary to pay attention to the uniform coating of glue, and do not have insufficient or too much glue.

5.Compacting the corners: Compacting the corners of the car film with a scraping board to make it more suitable for the glass.

1.Keep your hands clean when applying the film so as not to contaminate the glue or the surface of the car film.

4.When applying the film, it is necessary to avoid sticking to scratches or protruding glass, so as not to affect the lamination effect.

The methods and steps of car film are as follows:

1. Spread the solar film on the front windshield first, then blow it with a hair dryer to deform it, and smooth the solar film by hand while blowing to make it extend, which can fit the curvature of the glass;

2. Use a special tool to scrape the solar film flat, so that the film completely fits the front windshield. Use a knife to cut the film into the desired shape, and then remove the various annual inspection signs pasted on the windshield;

3. Gently take off the film that has been extended and cut the shape, spray the mixture of water and washing spirit on the front windshield, and then wipe all the dirty things on the glass clean, and then spray the mixture of water and washing spirit after wiping it clean;

4. Tear off the adhesive and gently stick the film on the glass stained with water and washing spirit mixture according to the shape cut before. Use a tool to expel all the water and bubbles between the solar film and the glass.

Car wrap tool preparation

Explosion-proof film pasting tools mainly include glass cleaning brushes, wipers, wipers, shaping scrapers, utility knives, watering cans, hot air blowers, etc.

Glass cleaning

Use a special glass cleaner to remove dirt from the glass as well as dust.

Cover

Cover the areas that will get dirty in the film, such as the lead and the door.

Cutting and blanking

First, measure the size of the glass to be filmed, then cut out the basic suitable film, and then stick the cut film on the wet glass, and trim it according to the shape of the glass.

Stereotyping

Because the front and rear window glass (and some side window glasses) have a slight spherical bending, which prevents the film from being flattened on the glass and is prone to wrinkles, the film should be shaped after cutting. The method is to heat the membrane with a hot air blower, and while heating, it is squeezed with a plastic scraper until it fits perfectly with the curved surface of the glass.

Internal cleaning

The adhesive surface of the glass should be further cleaned before pasting, and then the glass should be scraped clean and the frame should be wiped clean with a soft cloth and scrubbing paper.

Spray the installation fluid

After the inner surface of the glass is cleaned, the protective layer of the explosion-proof film is torn off first, and then the installation fluid is sprayed on the film and the inner surface of the glass respectively.

Paving

As the adhesive surface on the membrane temporarily loses its stickiness due to the spraying of the mounting fluid, the membrane glides smoothly on the clean glass inner surface, ensuring that the membrane can be adhered in place.

Squeeze water to dry

When the membrane is stabilized in its final position, the membrane surface should be sprayed again with wine installation fluid to lubricate the surface to be squeezed. A special squeezing tool is then used to remove all "bubbles" and as much mounting fluid as possible. Scrape the film from the center to the edges, from top to bottom and then to the bottom so that excess water drains out of the window frame.

Finally, wipe the edge of the glass with a towel to dry the moisture and mounting fluid.

Car film cleaning inspection

Once installed, scrub the inner and outer surfaces of all window glass to remove streaks and smudges. Finally, the paste quality should be carefully checked. One is to check whether the paste is firm, especially the corners; the second is to check whether there are bubbles; the third is to check whether the membrane is wrinkled; Fourth, check whether there are scratches.

If a problem is found, it should be reworked.

1. Spread the solar film on the front windshield first, then blow it with a hair dryer to deform it, and smooth the solar film by hand while blowing to make it extend, which can fit the curvature of the glass;

2. Use a special tool to scrape the solar film flat, so that the film is completely attached to the front windshield. Use a knife to cut the film into the desired shape, and then remove the various annual inspection signs pasted on the windshield;

3. Gently take down the film that has been extended and cut the shape, spray the mixture of water and washing spirit on the front windshield, and then wipe all the dirty things on the glass, and then spray the mixture of water and washing spirit after wiping;

4. Tear off the adhesive of the film, and gently stick it on the glass stained with water and washing spirit mixture according to the shape cut before. Use a tool to expel all the water and bubbles between the solar film and the glass.

First, the sun film is spread on the front windshield, and then the sun film is deformed by blowing with a hair dryer, and the sun film is smoothed by hand while blowing, so that it can fit the curvature of the glass; Use a special tool to scrape the sun film so that the film fits perfectly to the front windshield. Use a knife to cut the film into the desired shape, and then remove the various annual inspection signs pasted on the windshield;

Gently take off the film that has been extended and cut into shape, spray the mixture of water and washing spirit on the front windshield, and then wipe all the dirt on the glass, and then spray the mixture of water and washing spirit after wiping it clean; Peel off the adhesive and gently stick the film to the glass stained with water and detergent mixture according to the shape that was cut before. Use a tool to expel all the water and bubbles between the solar film and the glass.