If there is no artifact of rigid film, how to paste rigid film

Prepare the above four tools: tempered glass film, wiping cloth, vacuum cleaning paper, and wiping cloth.

How to paste tempered glass film.

Use an alcohol cloth to wipe off the grease and bacteria on the surface of the phone.

How to paste tempered glass film.

Use vacuum paper to suck up the alcohol and a small amount of dust.

How to paste tempered glass film.

Tear off the only release film of the tempered glass film.

How to paste tempered glass film.

Hold the edge with both hands and slowly lower it vertically.

How to paste tempered glass film.

Click on the middle, and the tempered glass film will be automatically adsorbed.

How to paste tempered glass film.

Finally, use a wiping cloth to check the surface of the tempered glass film that has been pasted and the mobile phone, and you're done.

How to paste tempered glass film.

end precautions.

When sticking the film, do not leave dust on the surface of the mobile phone, otherwise there will be bubbles when the tempered glass film is pasted.

If the glued part of the tempered glass film accidentally sticks to the dust, use vacuum paper to absorb the dust.

The tempered glass film can be washed with water and reused without affecting the viscosity.

Tempered glass is better than the general film, the wet wipes sent by the tempered glass film, wipe the screen first, and remove static electricity This step is more important. Then it is directly aimed at the sticker, and if you find that there is blistering, you will slowly push it out directly to the side. Generally, there is no problem, be careful not to fold, tempered can not be folded.

How to paste hard tempered film: 1Cleaning the screen is what we have to do first, take out our dry wipes bag, take out the cleaning wipes to clean and wipe the phone screen.

Pay attention to whether there are other foreign objects left on the mobile phone screen, and wipe the stubborn foreign objects a little harder to clean them more thoroughly. 2.Next, use a dry tissue to clean the phone screen again, pay attention to wipe the water and water stains left on the phone screen, if you don't want to leave marks under the tempered film, wipe it carefully.

Avoid windy places after cleaning, which may cause re-contamination of the cleaned screen) 3Take out the tempered film, tear off the protective layer of the tempered film, gently pinch both sides of the tempered film with one hand, and never touch the adsorption layer, if you don't want to leave fingerprints on the phone screen. 4.

Carefully align the front earpiece with the front camera hole, keep the top branch of the tempered film parallel to the top frame of the mobile phone, and gently put it down, and the tempered film will automatically adsorb on the mobile phone screen. (Pay attention to the distance between the left and right borders, it is ugly to stick to the deviation, and it is not easy to deal with) 5At the moment when you put down the tempered film, you can experience the perfect moment of technology adsorption.

Isn't it fun? 6.The corners of the tempered film are generally not well adsorbed, and we need to use a hard card wrapped in a soft cloth to nudge it to make it fit perfectly.

How to paste the tempered film yourself?

Nowadays, everyone will have at least one mobile phone in their hands, and we need to take extra care of it in daily use. Especially for the screen of the mobile phone, in order to prevent the screen from being scratched and broken, we generally put a tempered film on the mobile phone to protect our beloved mobile phone. But going out to find someone to apply the film is as little as dozens or as many as hundreds, which is still a bit expensive for the average person.

So we can consider buying mobile phone film from the Internet and sticking it ourselves. In fact, it's not difficult at all, but everyone follows my essentials to do it, and it will be more professional than the outside.

1. Buy tempered film:

First of all, we buy the tempered film from the Internet, pay attention to one point to adapt to the model in our hands, some tempered film will have black edges, you can choose according to your own preferences when you choose.

2. Alcohol wipe, clean phone screen:

It is best to replace the tempered film after buying the mobile phone. After the tempered film is bought, we can't paste it directly, we need to remove the dust and dirt on the screen first, we can open the alcohol wipe paper towel sent when buying the tempered film, and clean up the obvious dirt on the screen first, especially the edges.

3. Wipe off the fine dust particles with a dust-stained cloth

After wiping it clean, you can't stick the film right away, you have to stick the small dust on the screen in a bright place first, if you don't get rid of the film, no matter how small the dust will leave a small bubble on the mobile phone screen that can't be removed, not only ugly, but also very poor use experience. So be sure to keep cleaning up the dust that falls on the screen, remember.

4. Mobile phone film positioning:

After the screen is completely cleaned, it is time to start the film, in order to prevent the film from being crooked, we need to position the film, use the free positioning sticker, and position the tempered film in the middle of the screen. If it doesn't work once, you can try it a few more times, don't stick it crookedly, it's better not to stick it if it's crooked. After positioning, just put the film on it, and it will fit automatically.

5. Remove white edges:

After the tempered film is pasted, it will generally leave a little gap on the edge, at this time we have to take out the white edge removal liquid, squeeze a little along the edge, and then use a dry cloth to catch a circle, knowing that the white edge is all gone. Well, the film is pasted, isn't it very simple, not only improve your hands-on ability, but also save a lot of money, haha.

Precautions. The most important step is to clean the dust, I have pasted so much tempered film myself, and sometimes I accidentally paste the dust into it, causing permanent bubbles, the above is all the content of how to paste the tempered film by myself, I hope it will help everyone!

What kind of skills do you need to paste the tempered film? How to solve the problems that often occur in the film?

Filming skills sharing.

1. First disassemble the alcohol swab, wipe the mobile phone screen clean, and leave no fingerprints at all.

2. Wipe the screen with a gray cloth to avoid alcohol moisture residue, and wipe off dust, and wipe the screen carefully. Don't leave a single layer of ash behind.

3. Generally, when we go to buy tempered film, we will be equipped with electrostatic precipitator paper, and paste it on the screen with electrostatic paper to remove the static electricity of the screen to prevent dust. If you don't have static paper, you can observe it with your eyes, and if there is dust, wipe it again with a gray cloth, but don't wipe it with your hands, it will leave fingerprint marks.

4. Tear off the release film of the tempered film, hold the edge around it (note: do not touch the inner surface of the tempered film), aim at the screen, look at the edges around it, and the position of the home keyboard, gently put down the tempered film, and then gently press the middle of the screen sticker with your index finger to make the tempered film fit the screen, and finally use the scratch card to gently push to help the tempered film fit the screen and drive away the bubbles.

Frequently asked questions. Q: The tempered film is almost perfect, but there is a small corner that does not fit, what is going on?

Answer: It may be that the screen is not clean, pay attention to cleaning and wiping it clean, it may be a problem with the workmanship of the tempered film The problem of the mobile phone itself, some mobile phones themselves The screen is a little uneven, so it is not suitable for pasting the tempered film.

Q: What should I do if there are bubbles on the tempered film on the mobile phone?

Answer: There are two reasons for the formation of bubbles, one is that they may enter the air, and the other is that they are stained with dust.

When the air is inlet, simply use the included scratch card to push the bubbles out of the edges, and if you can't push them out, it is a dust problem. In the case of the ash layer, you can gently lift the tempered film upward, lift it to the place where the bubbles are generated, re-clean the bubble position to suck the dust away and re-paste it, and at the same time, in order to avoid the entry of air, you can use a scratch card to re-hang it. Until the sticker is flat and no air bubbles are generated.

After purchasing the tempered film, you can follow the instructions on the product description to apply the film.

Please follow the step-by-step instructions written in the manual.

It's very simple to paste the tempered film yourself, turn on the desk lamp, wipe the screen clean, and align it.