How to use Glost to backup and install the system, please ask the expert to give you detailed guidan

Start ghost, immediately enter DOS mode, first of all, the ghost version is introduced, click OK to enter the main interface, which can be divided into the following items:

local backup between local hard disks.

Backup between LPT network hard drives.

option setting (generally do not adjust, use the default value).

quit.

As a stand-alone user, we only choose LOACL which includes the following options:

disk operation options.

to disk A complete copy of the hard disk.

to image The contents of the hard disk are backed up as an image file.

from image Restore from the image file to the original hard disk.

partition Hard disk partition operation option.

to partition A full copy of a partition.

Back up the contents of the to image partition as an image file.

from image Restore from image file to partition.

check Function Options.

Steps:1Select Loacl Partition to Image to back up the hard drive partition with the suffix ".".gho".

2.Select the drive where the partition you want to back up is located and click OK

3.Select the partition you want to back up, that is, the system partition, and click OK

4.In the filename field, type the name of the image file, such as " and the storage location (Note: the partition being backed up cannot be selected), and then press the "Enter" key.

5.Select whether to compress, no to compress, fast low compression, high high compression. Generally, high compression is selected, the speed is slower, but 50 can be compressed

6.Now just watch the progress bar and walk slowly. The speed of backup has a lot to do with memory. I got 64M RAM and the transfer rate was 40M per minute. After upgrading to 128m, it is 70m per minute, which saves a lot of time.

7.Once you're done backing up, you can exit Ghost

Restore image files: (The size of the original hard disk partition must not be changed).

1.Select Local Partition from Age to restore the system from the image file.

2.Select the source partition to which you want to restore the image files and click OK

3.Prompt if you are sure about reverting, of course yes

After the recovery is complete, you are prompted to restart your computer and press Enter, just like you touched before the backup.

The one above is good, I can't do it.

The above is so detailed, the sprinkler family will not say much.

This is the BIOS interface.

That is, the basic input-output system.

There is no way to do this.

Select Continue to install the program with a glost disk.

Are you going to install GHO's system? Or do you want to do it?

Bois: This is generally the place where the U disk or CD is the first startup item, and then install the CD disk after the first startup item.

Ghost Pros; Re-backing up is easy, and you can have an unlimited number of backups and extract and modify the files in the backup at any time.

2. Installation; Unzip - Open - Press the prompt and click Next three times - Cancel the toolbar (if you don't want it) - Next - Install - Wait - Succeed - Press the prompt to back up automatically.

3. Ghost re-backup, choose one of the methods, and do it when the system is no problem.

1. Back up after booting, (simple).

Click Start Program One-click Ghost One-click Ghost Select Click One-click Backup Backup Auto-restart and wait for a few minutes before the backup is completed.

2. Back up at startup.

Immediately when the computer is turned on, the non-stop click button Wait for a few seconds, Chinese One key ghost brightens Immediately click Enter Wait for a few more Chinese options to appear, click Brighten the backup Click Enter to start the backup.

If only the two options (Resume) and (Cancel) appear, then hold down the ESC key at the same time to enter the main option.

Click ( Light up the one-click backup Enter to start the backup and wait for about 3 minutes.

Original method; You choose one or the other.

1. One-click ghost to restore when starting, (suitable for system crash and crash).

Immediately when the machine is turned on, it is clicked. Wait a few seconds to see the one-click ghost....Brighten up and click enter immediately Wait for a few Chinese options to appear, click the key to restore or restore brightened with one key Click enter and wait for 2-10 minutes to restore the finish.

Two; Restore after booting (relatively simple and safe).

Click Start Program One-click Ghost One-click Ghost Restore or Restore Auto Restart and wait for a few minutes to complete the restoration. Traces are clear (such as after restarting, see the recovery does not brighten the bright arrow, brighten it, click enter).

Take a look at my space in detail.

What I recommend is the anti-black screen version of the rainforest wood wind version,Partition actually doesn't use software,You can partition directly with the partitioning software that comes with Windows.,This answer is simple and clear.。

Encapsulating the system requires special software and requires some tweaks to the system, including drivers, which is cumbersome. The backup system is just a backup of your current C drive, which can be restored when your computer is poisoned or the system crashes in the future.

Start with One-Click Ghost! Especially suitable for beginners, you can understand it at a glance!

DOS House Down:

1key_g82_

Take a look at the help files inside and take your time! Something you can't learn!

In the future, if you have a boot disk, you will be bold, read more information, and you will be able to get out of the menu of one-click ghost! It's going to be a dog, ghost! Enter DOS, execute, play in English. Congratulations on your success!

glost???

This is that kind of software ...

Haha, if it's a ghost, agree with the upstairs point of view. ^_

.You misspelled it, it's ghost, not glost, the one you said in Chinese, it's software like one-click restore, although they are in Chinese, but after selecting "backup" or "restore", or enter the ghost of the English interface for backup or restore operations.

If you want to manually enter the English ghost, you can:

1. Go to DOS in One-Click Restore and manually enter the command (or just enter ghost).

2. Boot the boot disc to DOS and execute it (the disc needs to have ghost software on it).