When configuring the wireless network, according to the requirements...

There is a USB flash drive character display: the USB flash drive can be displayed on my computer, which means that the driver is no problem.

Write error: The storage medium of the USB flash drive is damaged or turned on and erased!

The specified file cannot be found: The installer cannot find the source file on the PC, it should be a PC software issue.

A cross appears: The actual state and the prompt state do not match, driving the problem.

Based on the above phenomenon, it should be that there is a problem with the driver of the wireless network card, and you uninstall it and reinstall it. Reboot the system and try again.

If you can't connect after repeated configurations and the wireless network card driver is configured correctly, then it must be a plug-in or a virus problem! It is recommended to clean up the plugin, antivirus, and redo it if it doesn't work! Good luck!

In fact, tell you that the wireless on this book is good,Your wireless network card driver may not be installed,You uninstall and reinstall it,It's best to use the windows configuration and not use the software that comes with the notebook (in other words, it's called third-party software,For example, HP's) configuration,Because it may lead to two conflicts,The result is that you can't access the Internet。

And don't understand what to do when configuring a wireless network?,Is it a wireless network card?

U disk read storage is broken, often out of order to pull out the U disk, easy to lose files, sometimes will burn out the U disk, bad U disk can be used, but unstable, and the situation you appear the same Heh· There is also a difference in the lower right of my book, which does not affect the installation of the system, and there is no need to care.

When configuring the wireless network, insert the U disk as required, there is a U disk character display, but it prompts an error when writing, this can be reinstalled, and a cross appears when the wireless network is used on this book, prompting that it cannot be configured? It's because you didn't turn on the wireless connection switch on the computer...

You remember that there is a small software on the Internet to quickly change the IP address, you first fill in the IP address and DNS you need there, and if you want to change it later, you can click on the software to automatically change it, and I will help you find it now.

Is it that the driver of the wireless network card is not installed properly?

What model of notebook is it? Wireless routers? At which step is the USB flash drive displayed? Can I reinstall the system?

Infrastructure mode configuration: Infrastructure mode refers to the use of ** devices, such as routers or access points, in a wireless LAN to control and manage a wireless network. In this mode, the wireless device needs to establish a connection with the device to access the network, and the device can provide network authentication, encryption and other functions, and can also infiltrate to manage and control the access range, speed and other parameters of the wireless network.

Infrastructure mode is currently the most widely used wireless network configuration mode, suitable for most homes, offices and other places.

Ad hoc network mode configuration: Ad hoc network mode refers to the direct communication between wireless devices to form a self-organizing network structure. In this mode, wireless devices do not need ** devices to manage and control the network, and can independently select the connected devices to achieve seamless roaming and adaptive networking.

The ad hoc network mode is suitable for some special occasions, such as in the field or at the disaster site, where it is necessary to quickly build a network-sensitive residual network.

These two wireless network spine configuration modes have their own advantages and disadvantages, and you need to select the appropriate mode according to your actual needs and scenarios.

1. Turn on the wireless network acceptance switch;

2. The main program setting is to open the wireless Internet access and open the "properties" of "online neighbors" to "wireless network connection status" in the properties of the online neighbors;

3. If there is no wireless network connection status, you need to install a wireless Internet driver, and there is a driver when you buy a laptop.

4. In the "Properties" in the "Wireless Network Connection Attributes", click "Wireless Network Configuration", click "Link" in "Add" under "Preferred Network", set the service name SSID to be the same as the ESSID of the AP, and then use DHCP to set the IP to automatic file fast acquisition. All settings are complete.