When the memory card is formatted, it says that Windows cannot complete the formatting

Formatted in Explorer.

Then it's a direct format to DOS.

If you can't do either, you're stuck in poison.

And then is your card reader good? Be sure!

Hi Format Data Recovery Master is a powerful, simple interface, and simple to operate data recovery software. It supports the recovery of hard disk files deleted by mistake, disk formatted by mistake, memory card data deleted by mistake, files emptied by mistake, and hard disk files after the hard disk partition disappeared.

Change to a computer with anti-virus software, it may be caused by a virus, if it still doesn't work, the card is broken.

I've been in this situation before.

I guess I haven't used this card in a while.

I don't want to say it, but. . . Ka because of moisture... Broken ...

The reason is that the operating system has not detected the problem caused by the USB flash drive.

The workaround and detailed operation steps are as follows:

Tool: Windows 7.

1. First of all, connect the memory card to the computer, then click the start button in the bottom left corner, click the "Run" option in the pop-up menu as shown in the image below.

2. Secondly, in the pop-up window, enter "cmd" and click the "OK" button as below screenshot shown.

3. Then, enter the "X: FS:FAT32" command in the pop-up DOS window.

Note that the x in the instruction refers to the disk character inserted into the memory card. After entering the command, press Enter. At this point, you will be prompted if the memory card is connected. After confirming the connection, press enter again and the system will start formatting as shown in the image below.

4. Finally, it will take some time to format the memory card. After the formatting is completed, press the enter key, and then solve the problem that the memory card says that Windows cannot complete the formatting, as shown in the following figure.

If the memory card is damaged by the channel, you can try to fix it by a series of methods

1. Click Start Run and enter "cmd format f: fs: fat32" (where f: refers to the drive letter where the memory card is located).

2. Open the Control Panel Management Tools Computer Management Disk Management Find the drive letter where the USB flash drive is located Right-click Delete the disk partition (this option is grayed out and cannot be selected) Create a new disk partition After completing the disk partition according to the prompts, you can format the memory card.

Formatting risk: After formatting the memory card, the data will be completely lost and restored to the initial state, which cannot be retrieved even with ordinary recovery software. Therefore, when formatting the memory card, you should pay attention to backing up the more important information inside.

Format is the operation of initializing a disk or partition within a disk, which usually results in all files in the existing disk or partition being erased. Formatting is usually divided into low-level formatting and high-level formatting. Unless otherwise specified, formatting a hard disk is usually referred to as advanced formatting, while formatting a floppy disk usually includes both.

Advanced formatting, also known as logical formatting, refers to an operation that writes specific data to a specific area of the disk according to the file system selected by the user (such as FAT12, FAT16, FAT32, NTFS, EXT2, EXT3, etc.) to initialize the disk or disk partition and clear all files in the original disk or disk partition.

Advanced formatting includes rewriting the corresponding area of the partition table in the master boot record, and setting aside a piece of disk space in the partition for file management, such as file allocation tables and table of contents, according to the file system selected by the user, so that the user can use the partition to manage files.

Insert the TF card into the SD card holder, then insert the card reader into the computer or directly into the SD card holder of the notebook, after the machine reads out, click the mouse on the disk of the SD card, right-click, click Format, and do it according to the program.

Low-level repair, with mass production tools, and if it doesn't work, it means that the card is scrapped.

Method steps.

3Maybe some friends have a lot of good things in the USB flash drive or memory card, and they don't want to be lost after formatting, so use software to recover the data first, and then format it. Recover data with software using Digital ObjectRescue Pro.

4Rebuild the partition table and fix the SD card that cannot be formatted. Some SD cards are recognizable on a computer, but cannot be read or written. When using the built-in formatting tool of Windows, the "file system is raw" is displayed when formatting, and the formatting cannot be completed.

SD card repair tools such as mformat, portfree, etc., will not help it either. What should we do when we encounter this kind of failure?

5 First of all, the faulty equipment can be identified by the system, which is usually a software failure, and the software failure can usually be repaired by using some tools and software. It's a pity that some users have sentenced SD cards that can be recognized by the system but cannot be formatted.

6 We know that when the partition table of the hard drive is corrupted, the formatting cannot be done either. In this case, you can use the partition tool FDISK that comes with Windows to rebuild the partition table. This idea of solving hard disk failures can also be used on SD cards, but the specific methods are slightly different.

Step 1: Insert the SD card into the computer and turn it on. Right-click on the "My Computer" icon and select "Manage", and the "Computer Management" window appears.

Step 2: Click on "Disk Management" under "Storage" on the left side of the window, and the screen will show the information of all storage devices in the current system. Disk 1 (removable) is the SD card to be repaired.

Step 3: Point to Disk 1, right-click, select New Partition, and then select FAT32 or NTFS, the system will prompt that the partition has been created successfully.

Step 4: Format the SD card.

With the above mentioned steps, the SD card can be repaired.

7 Solutions for Unable to Format SD Card.

Symptoms: You can find it, but when you open it, you will be prompted to format it.

Causes: 1. The disk may not be forcibly removed according to the normal steps during operation, resulting in the loss of system information in the disk.

2. The file system of mobile devices including memory cards should generally be: fatfat32, if the device (SD card) attribute shows that the free space and the used space are 0, the file system is RAW. That's why it's not recognized.

Workaround: In Run - Enter: Open Computer Management - Disk Management:

You can see the device, click right click here to format it, and it's OK.

When the phone is unformatted, it prompts that it is damaged.

The question can be opened on the computer, and the content inside can be recognized, and you can see it, but it can't be formatted, and the formatting is a prompt failure.

When you put it on your phone, you can't even open it.

Answer 2, hard fault: due to the sudden pull out of the memory card voltage instability may cause the memory card in the essence to be damaged or the chip burned, in this case, I recommend you to find a professional data recovery company, generally if it is a soft fault recovery ** in about 200-300, if the hard failure needs to polish the memory card to extract the essence recovery then 3000 up, do not try it yourself to avoid the failure aggravated. If you don't have important data, I suggest you change your card!