How Satellite Dish 9 was upgraded machine to machine

Now even if you upgrade successfully, it is estimated that you can't see a few days of password and change, recently changed several times, I upgrade and upgrade are annoying, every time I have to spend money to let others to upgrade, now the satellite dish is estimated to be sold, decryption is too troublesome, this boss does not want to give me to take the solution, they are not unreasonable and said: "We are not a manufacturer, I still have a lot of goods not sold, and I will not be returned, who do I find?" ”

Brother, you don't say anything in detail, who can... What brand of your house. I don't know what model of motherboard it is. I'll tell you about it, there's only machine-to-machine upgrades. Or change the storage block.

First of all, you need to have a mother machine, that is, a machine that has been upgraded to a higher level. Connect the two machines with an upgrade cable, both machines must be connected to the power supply, and then turn on the sub-machine after the upgrade screen appears on the master machine. Wait until the upgrade is complete, turn off the handset.

Zhongxing No. 9 upgrade crack method tutorial:

Zhongxing 9 has been upgraded, teach you how to crack the Zhongxing 9 receiver after upgrading, and decrypt the Zhongxing 9 receiver upgrade tutorial.

Crack method 1:

Since the upgrade of the Zhongxing 99 satellite, some copycat machines can not complete the automatic upgrade when they are turned on, and they have just tested with a garbage Tiancheng machine, and they will be automatically searched after they are turned on.

After the display is found 0 sets of TV + 0 program set of radio programs, at this time the remote control can be used, the receiver is in a state of no program, and then connect to the signal line, enter the Lai Order, the four groups of ** devices for manual search, note, must be manual, automatic search will crash again, the receiver can resume normal operation after the manual search is completed.

Crack method 2: factory reset.

The upgrade program does enter the receiver, but if the upgrade program is started, only the serial number changes from to , and the upgrade bar does not change at all. Then it automatically enters the automatic search, and after 39%, the progress bar does not move. But the frequency is changing all the time, interrupting and exiting.

Not a single show was left behind. Uninterrupted rollouts, the frequency is increasing all the time. It's like a dead machine.

The solution is to go to the settings, go back to the factory state, and the password is 9999 or 0000Then enter the manual search, there is no program at the first frequency point, and there is a program when you enter the frequency point 2 search, and there are programs at the third and fourth frequency points, and there are 54 programs at the three frequency points of 2, 3, and 4.

Cracking method 3: copycat upgrade.

The middle nine machine is upgraded to the machine, and the mother machine is one. In fact, it is a machine that can be seen at the moment. One serial port line. A handset is only a few that cannot be upgraded or continuously displays the upgrade status.

Steps: 1. Connect the serial cable behind the machine.

2. Press the F4 button three times --- the mother machine is energized.

3. Make sure that the panel of the parent computer is displayed ON at this time.

4. The handset is powered on, and the panel is displayed as messy.

5. At the start of the upgrade, the panel of the parent computer shows that 001 to 099 will become E-P and finally 001. The upgrade was successful.

Middle 9 machine upgrade must-have 1 computer 2 upgrade tools 3 suitable files.

Indispensable.

Only professional places have something to upgrade.

Turn on the receiver, connect the TV, press the remote control "menu" to select "System Settings", which has "Installation and Signal Detection", generally there are 1-24 frequency points, find a frequency point with green. Then turn the antenna pot until the "signal strength" and "signal quality" green indicator bar are about 70%, and you can receive the program.

First of all, you have to name the model of your machine, otherwise there are many ways.

1 Assemble the lid of the pot, 2 Install the high-frequency head (the F connector of the high-frequency head is down), 3 Connect the receiver and TV.

4 The receiver and the high-frequency head are connected through a feeder.

5 After the small pot lid and the receiver are connected, press the F3 button on the remote control (or the star adjustment button), the signal strength and signal quality are displayed on the TV, the strength is 60%--70% (this must be there, there is no indication that the feeder is not connected well or the high-frequency head is bad), the signal quality is 0, now you can adjust the pot lid, turn the antenna up and down left and right to find the star, the general orientation is southwest, and look at the signal quality when turning to make it the highest (the general receiver reaches 50% to reach the threshold, you can produce an image).

6. Fine-tune the lid and high-frequency head to achieve the highest signal quality (70%-80%) (the most important thing is to turn the pot slowly, be patient).

7 Press the exit of the remote control. You can tune in to the show.

You can use the following three methods to try, maybe it will help you.

Since the upgrade of the Zhongxing-99 satellite, some copycat machines cannot be automatically upgraded when they are turned on. After turning on the machine, the automatic search to 39% will cause a crash, and the remote control fails at this time and cannot be exited. Note! It's not a crash.

Solution:Unplug the signal cable,Automatic search will be completed,Due to no signal search,After the search, it is displayed that 0 sets of TVs are found,But at this time, the remote control can be used but the receiver is still in a state of no program。 Then connect the signal line, enter the Laidan, and manually search the three groups of ** devices.

Crack method 2: factory reset.

I tried it today, and the upgrade program did enter the receiver, but if you start the upgrade program, only the serial number changes from to , and the upgrade bar does not change at all. Then it automatically enters the automatic search, and after 39%, the progress bar does not move. But the frequency is increasing all the time.

You interrupt and exit. Not a single show was left behind. You don't interrupt the rollout, and the frequency is increasing all the time.

It's like a dead machine.

The solution is to go to the settings, go back to the factory state, and the password is 9999 or 0000Then enter the manual search, there is no program at the first frequency point, enter these three frequency points 11892l8800, 12100r r8800 and there will be a program. It's the same as before.

Cracking method 3: copycat upgrade.

The middle nine machine is upgraded to the machine, and the mother machine is one. In fact, it is a machine that can be seen at the moment. One serial port line. A handset: A machine that cannot be upgraded or continuously displays the upgrade status.

Steps: 1. Connect the serial cable behind the machine.

2。When the mother machine is powered on--- press the F4 button three times.

3。Are you sure. At this time, the panel of the parent computer is displayed on.

4. The handset is powered on, and the panel is displayed as messy.

5. At the start of the upgrade, the panel of the parent computer shows that 001 to 099 will become E-P and finally 001. The upgrade was successful.