How to make a tumbler? How does a tumbler not fall?

This shouldn't be a food issue, right?

To make a tumbler depends on what material you use, if you use eggshell, you need to make the small head of the egg and the hole on the back of the hole slightly larger and break the membrane inside, and then blow from the hole in the small head, blow the eggs out, wash and dry the eggshell, you can use a hair dryer to dry. Then put some small steel balls (bicycle repair or hardware stores are sold) into the eggshell (of course, from the larger hole into it), the amount of small steel balls is about one-fifth of the volume of the egg, the amount is less tumbler can not stand, try a few more times, slowly add, add until you are satisfied; You can also use small stones and sand instead of small steel balls, which are heavy and have good results.

After the small steel ball is put into the eggshell, the eggshell is placed upright and fixed, and then the 502 glue (to use a large bottle, the small bottle is not enough) is dripped into it, so that the small steel ball and the eggshell stick together, after the glue is dry, it is OK. Then it's just a matter of doing some beautification.

If you can't stand or stand very slowly after the tumbler falls, it means that there are fewer steel balls, and you need to add more and glue them well. The amount of small steel balls should never exceed one-third of the volume of the eggshell, otherwise it will never stand up. Another is that the small steel balls should stick to the bottom of the eggshell, don't stick crookedly, otherwise they will become tilters.

Objects that are light at the top and heavy at the bottom are more stable due to the low center of gravity.

The tumbler is easy to make.

Step 1: Prepare the materials, double-sided tape, eggshell, plasticine, glue, scissors, markers, compasses, cardboard.

Step 2: Draw a fan with a compass on the prepared cardboard.

Step 3: Cut out the painted fan.

Step 4: Roll the cut fan into a cone, paste the double-sided tape and fix it to form a cone.

Step 5: Put the plasticine into the eggshell, do not fill it, only take up 2 3 of the eggshell.

Step 6: Connect the finished cone with the eggshell placed in the plasticine to form a tumbler.

Step 7: Place the tumbler on a smooth table, try to push it, and the tumbler will automatically stand up again.

1Take a raw egg, make a hole at one end of the egg, and pour out the egg mixture;

2. Take another piece of colored paper, cut out a semicircle, apply glue at one end of the semicircle, glue the two sides together, and make a tumbler hat;

3. Then fill the eggshell with rice (or pebbles), and then squeeze it into the hot melt adhesive to fix;

Glue the inside of the hat and stick it to the eggshell.

4. Rub a circle of glue on the inside of the hat and stick it to the eggshell;

5. Finally, draw the eyes and mouth on the hat and you're done.

Tools needed: eggshells, colored paper, colored pencils, scissors, glue.

1. Prepare the materials for making tumblers, as shown in the picture below:

2. Open the egg from the pointed end and wash it, and put in a weighted object, as shown in the picture below

4. Cut off the part of the circle quarter, as shown in the figure below

6. Glue the conical shape to the egg shell, as shown in the figure below

7. Draw an expression on the eggshell with a colored pencil, as shown in the picture below

Eighth, such a tumbler is done, as shown in the figure below:

On August 28, the fish and vegetable courtyard was filmed.

The tumbler is easy to make.

Make a mold and move his center of gravity down as much as possible, just like an egg tumbler, only about half of the sand, and lower the center of gravity, and a simple egg tumbler is ready.

Take an egg out of the bag, take a toothpick, use it to make a small hole in the top of the egg, and slowly pour the yolk and egg white out of the small hole. After that, carefully dig the hole a little bigger with your little finger, gently stuff some plasticine into the eggshell, and finally seal the hole with adhesive, and then the shape of the tumbler is almost out, but it is not very pretty. So I took another piece of orange paper, carefully cut it into a triangle, and rolled it into a little hat and put it on top of the tumbler's head.

The final step is to dress it up with bright colored pencils.

Use scissors to poke a small hole in the tip of the egg, and be careful, it must not be too big! Then pour out the egg yolk and egg white, preferably in a bowl, and eat it, wash the eggshell with water and dry it with a hair dryer. Pour soybeans or sand into it, no more than 1|3. Otherwise, you won't be able to stand up.

Light the candle, drip the candle water into the egg, fix it, make a hat on top of the hole to cover the hole, draw the nose, mouth, and that's it

Recently, the school has to hand in handmade products, but don't always be unavailable, there is wood and something else? (⊙o⊙)？

Tool materials: double-sided tape, eggshell, plasticine, glue, scissors, marker, compass, cardboard.

Here's how to make a tumbler:

1. Draw a fan shape with a compass on the cardboard and cut it out.

2. Roll into a conical shape and paste double-sided tape to fix it.

3. Put the plasticine into the eggshell.

4. Connect the finished cone with the eggshell.

5. Place the tumbler on a smooth table, try to push it, the tumbler will automatically stand up again, and the tumbler will be ready.

A tumbler is a fun and educational toy that can help children develop their sense of balance and hand-eye coordination. It's not difficult to make a tumbler, and I'll go into more detail for you below.

Prepare materials The materials required to make tumblers include: plastic bottles, cement, sand, colored paper, colored ropes, etc. Among them, plastic bottles should be of good quality and moderate size.

Make a cement base Prepare a container with a moderate depth, mix the cement and sand in proportion, add an appropriate amount of water and stir well, pour it into the container, and then insert the bottom of the plastic bottle into it, let it be embedded in the cement and fix, and when the cement is completely dry, the cement base is ready.

Making the top half of the tumbler Cut the colored paper into a rectangle of the appropriate size, then roll it into a cylinder, then place a small sphere into the cylinder**, and finally cover the top with another colored paper and secure it. This spherical part can be painted with cute little animals or people to make it more lively and interesting.

Drill a hole in the cement base, pass the colored rope through the hole, and then tie the colored rope to the ring on the top of the plastic bottle and the tumbler sphere, and tie the two ends of the colored rope to control the balance of the tumbler.

Adjust the balance Using your hands, gently lift the bottom half of the tumbler sphere so that it remains vertical. Adjust the length of the string so that the tumbler is balanced. When the tumbler is tilted to one side, the balance can be restored by pulling the corresponding colored rope appropriately.

These are the simple steps to make a tumbler, you can improve and innovate according to your preferences, and make a more personalized and creative tumbler toy.

Here's how to make a tumbler:

Step 1:

Take out a raw egg, use chopsticks to make a small hole in the top of it, remember, not too big, and pour the egg mixture into the bowl. Then clean the inside of the eggshell with water.

Step 2:

Once the water in the eggshell is dry, you can put something weighty into the eggshell, such as a small iron nail or sand, from a small hole.

Step 3:

After putting an appropriate amount of weight inside, you can seal it, you can use candles or glue. Then draw some expressions or other favorite patterns on the eggshell. That's it.

How tumblers work:

The tumbler principle is that objects that are light at the top and heavy at the bottom are more stable, that is, the lower the center of gravity, the more stable.

When the tumbler is balanced while standing, the distance between the center of gravity and the contact point is minimal, i.e., the center of gravity is the lowest. When you deviate from the equilibrium position, the center of gravity will always be higher. Therefore, the equilibrium of this state is a stable equilibrium.

So no matter how much the tumbler is shaken, it will never fall.

For example, the experiment of "rolling on a cone" seen in the science museum is also for this reason, although the shape of the cone and the shape of the tracks on both sides cause the center of gravity to fall, but it looks as if it is rising, and the upward scroll is inconsistent with the facts in life. But it's just an illusion, and in essence, the center of gravity drops, and the lower the center of gravity, the more stable.

Summary. Kiss. Hello, to make a tumbler first you need an egg.

1.Shake an egg a few times and then knock a hole. 2.

Then pour all the egg yolks and whites into a bowl. 3.After pouring, fill the eggshell with sand and fill the eggshell.

4.Then cover the hole with white paper and glue it with clear glue. 5.

Finally, find a cute avatar paper, wrap it around the white paper, glue it, and you're done.

Kiss. Hello, to make a tumbler first you need an egg. 1.

Shake an egg a few times and then knock a hole. 2.Then pour all the egg yolks and whites into a bowl.

3.After pouring, fill the eggshell with sand and fill the eggshell. 4.

Then cover the hole with white paper and glue it with clear glue. 5.Finally, find a cute and callative avatar paper, wrap it around the white paper, and stick it to the skin, so that it is done.

The tumbler is an ancient Chinese children's toy, which was first recorded to appear in the Tang Dynasty. Shaped like a human being, it is shaped and weighted, swaying when touched, and then returning to an upright state. The tumbler can also be compared to some people who are good at responding to the orange circle and paying the environment and can maintain their power for a long time.

The manual steps of the tumbler are as follows:Preparation tools Raw materials: cardboard, bottle caps, glue.

Steps. 1. Cut the cardboard into squares and fold it halfway through.

Steps. 3. Draw a cute pattern in the right place for the two circles, and make two copies of the same shape.

Steps. Fourth, squeeze the glue into the cap of the bottle and paste the pattern of the same size on the opposite side.

Steps. Fifth, according to the above steps, a simple and good-looking tumbler is ready.

The principle of the tumbler:

1. The object with light on the top and heavy on the bottom is relatively stable, that is to say, the lower the center of gravity, the more stable. When the tumbler is in equilibrium in the erect state, the distance between the center of gravity and the contact point is the smallest, that is, the center of gravity is the lowest. After deviating from the equilibrium position, the center of gravity is always raised.

Therefore, the equilibrium of this state is a stable equilibrium. So no matter how much the tumbler swings, it always doesn't fall.

2. For example, like the "cone rolling" experiment we saw in the Science and Technology Museum, it is also the same reason, because of the shape of the cone and the shape of the tracks on both sides, its center of gravity is falling. But it is only an illusion, and seeing its essence, the center of gravity is lowered, so the lower the center of gravity, the more stable.

3. In order to increase the stability of objects in life, we often use weights to increase the following, such as fan bases, microphone stands, bus stop signs, etc.