Why can I plug in the network port of my bedroom and connect to the computer with a broadband connec

I can say with certainty: it's the router's problem. Because there is no mention of whether you can access the Internet, as long as your router is good, the power is on, and you can enter the router settings after connecting to the computer through the network cable (most routers are at this address).

There is no doubt about this, if you can't even get in, it means that there is a problem with the line from your computer to the router. You can slowly check it, there are nothing more than three possibilities: your computer problem, network cable problem, router problem.

In addition, it is recommended that you try a few more times, because sometimes the router will be sluggish, and sometimes it can be entered a few more times.

Finally, teach a trick,Restart the router,This trick is tried,If you don't know how to restart, you can check the manual,Generally, there is a reset button on the machine。

Keep it simple.

If you do not configure an IP address, the router should support DHCP (automatic IP assignment).

Therefore, it doesn't matter if the network cable is plugged in upstream of the router, and the reason why you can't connect to the host.

It is possible that your computer network card has been equipped with an IP address, and the probability is 90% If you don't know how to find the IP configuration, I won't teach it.

Update: If you take a good router and the problem persists, then the problem must be on your console.

The problem with the network card can be quite large.

The router needs to be set up Only when it is set up can you use the router to surf the Internet.

In fact, it's also very simple, right-click on the online neighbor, click on the property, follow the prompts, it's not that complicated, just try it slowly.

Let's see if there is any problem with the route.

It is not possible to connect directly to the WAN port of the router. You also need to make some necessary settings on the router, such as setting the dialing type, and entering the account and password for surfing the Internet. Take the TP-Link router as an example, 1Connect the network cable to the WAN port.

2.The other network cable is connected to the LAN port at one end and the computer at the other end.

3.Open a browser and enter the administrative address of the router, such as:

4.After logging in, you can go through the Setup Wizard to configure the basic information as required.

5.After the following settings are completed, you can surf the Internet normally.

6.Find Network Parameters --WAN Port Settings.

7.In the first item on the right, select PPPoe in the "WAN port connection type", enter the Internet access account and Internet access password, and click Save.

8.Once you restart your router, you're good to go.

Whether you can enter or not can enter the routing interface has nothing to do with whether you are connected to the cat or not.

As long as the route supplies power.

The computer can log in to the route by connecting to the LAN interface.

The WAN interface is plugged in.

LAN is plugged into various Internet devices at home, don't get it reversed.

Broadband connections are not routed for direct dial-up connections.

If there is a route, use the local connection.

The computer no longer needs to be connected with a broadband connection, and you can access the Internet if you connect to the local connection, provided that the router is set up.

The situation you are talking about is very normal, if you connect the home network cable to the WAN port of the router, then the route will automatically dial up, and you don't need to dial up again when you use the computer to access the Internet! If the routing is set correctly, connect to the computer with a network cable from the router LAN port, and you can go directly to the Internet without dialing up!

And if you connect the home network cable to the LAN port of the router, then the route will not work at all! Wireless doesn't work!

Wireless routers, as long as they are connected to the power supply, will emit wifi signals, but the key is whether the router is connected to the WAN or not!

1. Connect the home network cable to the WAN port of the router, 2. Connect your computer with another network cable at one end, and connect the LAN port of your router at the other end

interface! 3. Open the computer, open the browser, enter the route login IP in the address bar, 4, enter the route login account and password in the pop-up dialog box, friendly reminder, if you don't know the route login IP, login account and password.

code, you can turn the route over and look at it, and there is a writing on the back of the route!

5. After entering the routing setting interface, the quick setting interface will generally pop up, and you can select the broadband dialing method in this interface.

PPPoE, enter your Internet account and password!

6. After the settings are completed, save the exit and restart the route!

Once the routing restart is complete, your routing hardware connection and setup are complete!

In addition, there is another point to remind that if your home is a ** line and there is a cat, it is recommended that you turn off the power of the cat when you set the route, and when the route is set up, turn on the power of the cat!

You don't need to dial up when using a router, and if you dial up to access the Internet, it means that you have plugged in the wrong network cable. To plug in the WAN Upstream Routing Configuration page, set your broadband account into the routing and let the routing dial first. That's how you'll have the internet.

When you plug the cable into the WAN port, and one of the other four is plugged into the computer, it is a normal router at this time, and it may be that the wireless settings are wrong when you can't connect your mobile phone.

When you plug the line of the WAN port into one of the other four ports, it can only be used on the computer, and there is no routing function.

If it is installed in the WAN port, the routing dial-up does not need to be established on the computer.

You need to enter the routing settings interface to set it, the address is, enter it in the browser, and the account and password are admin

There is a bit of a guide to get in, just do it step by step.

Hello First of all, confirm that the network cable is okay or the network is off, and the indicator light of the network stop modem is only two on. If it's normal, then check your own computer for problems:

Right-click on my computer --Management --Services & Applications --Services, and see if there is a DHCP service, is it not enabled? If it is not enabled, set the startup type to "Automatic" and start it!!

Then check the network card driver and update the driver, and the IP acquisition should be automatically obtained.

Hope it helps

The key is that you need to re-enter the account password to be able to connect, because you are dialing in with broadband, and you are away from home and using another account, then the network card will not be recognized.

Set IP and DNS addresses to be obtained automatically. Refresh your broadband account at the business hall and take a look.

Changing the IP must be effective, your router is online. The IP must correspond to the router!

Set up a new network connection.