How to cover the back cover of the watch 5, how to cover the back cover of the watch

1. Before closing the back cover of the watch, you need to check whether the meter opening tool is ready, under normal circumstances, only a special meter opener and a steel knife are needed.

2. We must be clear about what type of watch back cover we have, our watch back cover is generally divided into three types, one is a spiral waterproof watch, which has threads on the upper shell and back cover, and relies on the thread to make the upper shell and the back cover tightly screwed.

The universal watch opener can open the back cover of watches of different sizes and different patterns. Each of its buttons can be changed in angle and the distance can be adjusted by means of an adjustment handle and an adjustment disc. The universal watch opener is equipped with several buckles of different shapes, which can be selected according to the four embossed patterns of the back cover of various watches.

3. After selecting the corresponding size, the multimeter opener bayonet is stuck on the notch of the threaded back shell, the notch is aligned with the back cover of the watch, and then the multimeter opener is turned counterclockwise to cover the back shell of the threaded watch.

4. Screw back cover, this kind of back cover has threads, just like screws, only need to use the right tools to be able to unscrew. The two-prong opener, or three-prong opener, only needs to adjust the distance of the claws so that he can jam the card slot, and then rotate it counterclockwise to open. However, because the watch is too thin to hold steadily, it is still necessary to use a retainer to fix the watch and then unscrew it.

5. Place the back cover of the table on the hard table. Place a soft cloth on the front glass of the watch and press down with the palm of your hand to apply even pressure. Adjust the position of the lid, such as which direction the notch is facing, so as not to buckle the wrong position.

Turn the lid down with the front of the watch facing up. Balance the gaps on each side of the lid (keeping all directions basically the same). In this way, the back cover of the watch was successfully replaced.

6. Sleeve type waterproof watch. Its case sleeve is pressed against the case back. The shape of the back cover of this watch case is more special:

There is a high wall around it, the movement is mounted in the wall of the back cover, the watch glass is directly mounted on the back cover wall, and the upper case cover is pressed in, the watch glass and the back cover are tightly covered. For this type of watch, simply press the back cover with your thumb and push it open to one side.

I have a beer bottle, and the cap is pressed down vertically on the back cap, and it is easy to close it. Pay attention to the position of the alignment knob with a notch on the back cover of the watch.

If it is the kind that is directly covered, use a piece of cloth to pad it underneath, and press the watch cover with something in turn, so that it can be pressed evenly, otherwise it will be warped on one side, and it will not work by hand alone, and it will not be able to use even force.

There is a sealing ring behind the watch, is it stuck or something? Take a sponge, wipe these clean, and then take a pair of tweezers and micro-manipulate it under the lamp, adjusting the angle correctly.

I put the cover upwards with pliers, found the balance position of the cover, and used a rolling pin to solve the problem

The uneven border is not aligned and cannot be pressed on the inside and outside.

Rotate the lid and push it harder!

I just found the answer a lot of nonsense, now I got the watch cover, you have to find a notch in the watch cover and align it with the iron rod that turns the watch, and then hold this side with your hand and don't let it turn, wrap the other side with a tissue, and then bite it with your teeth, you have to be hard, and then you will listen to the bag click, and then bite the other side with your teeth, and that's it.

To open the back cover of the watch, you only need to jam the back cover of the lid opener, and then hit it hard with a hammer, the specific steps are as follows:

Preparation tool: one cap opener.

1. Prepare a special lid opener and place your watch upside down, with the back side up.

2. Find the gap between the back cover of the watch and the watch, aim the lid opener at this gap, and then firmly snap the lid opener into this gap.

3. Take a hammer and use the hammer to vigorously tap the tail of the cap, and the back cover of the watch will be opened after a few taps.

1. Take opening the back cover of a mechanical watch as an example and push the back cover open with your fingers, as shown in the figure below

2. You can see that there is a high wall around the shape of the back cover of the case, as shown in the figure below

3. The watch glass and the back cover are tightly covered, as shown in the figure below

4. Spiral waterproof watch, relying on the action of threads to make the upper shell and the back cover tightly screwed, as shown in the figure below

5. As long as you have a good grasp of the strength, it is easy to open the back cover of the watch, as shown in the figure below

Cover the mechanical watch.

Back cover, prepare the mechanical watch and back cover, pick up the back cover of the mechanical watch, and cover the back cover of the mechanical watch on the watch; The specific steps are as follows:

1. Prepare the mechanical watch and back cover.

2. Pick up the back cover of the mechanical watch.

3. Put the back cover of the mechanical watch on the watch.

4. Adjust the position.

5. Pinch the back cover and screen of the mechanical watch with both hands and pinch it hard.

6. It's covered.

1. Take opening the back cover of a mechanical watch as an example and push the back cover open with your fingers, as shown in the figure below

2. You can see that there is a high wall around the shape of the back cover of the case, as shown in the figure below

3. The watch glass and the back cover are tightly covered, as shown in the figure below

4. Spiral waterproof watch, relying on the action of threads to make the upper shell and the back cover tightly screwed, as shown in the figure below

5. As long as you have a good grasp of the strength, it is easy to open the back cover of the watch, as shown in the figure below

Question: What kind of mechanical watch is the kind of mechanical watch that Bo Tourbillon.

Answer A pry cover, this kind of back cover is pressed flat. It is usually used on business watches and other varieties, and the waterproof level is relatively low, and most of them are waterproof with 3 air pressure. This kind of back cover is usually at 3 o'clock or 12 o'clock, and there is also an opening opening at one of the 6 o'clock, which can be opened with an opening knife or professional tools.

bScrew-back cover, this back cover structure is usually used on highly waterproof watches. Most of the back covers will have six equidistant dimples (five for the Omega Seahorse) around the perimeter of the back cover to act as a fixed point to open the back cover of the watch, which can be opened with a hand wrench or a table wrench. There are also polygonal lace as opening fixed points, and Rolex uses a special tool to open the coin pattern.

c There are also symmetry point screws, and many high-end or high-end material cases use this structure. The seal is also better than picking the cover, and the back cover can be opened by unscrewing the screws with a screwdriver.

The above is the structure of the vast majority of watch back covers, but there are also some other types of back cover structures, some even do not have back covers, the watch movement is put in from the direction of the watch glass, and the glass must be removed first when the back cover is opened.

The question is not seamed, nor is it screwed.

That should be a screw-back cap.

Would you mind taking a picture of ** and show it to me.

Asking questions is not a spiral.

1.First, remove the strap by clamping the watch shaft with tweezers.

2.Pry open the dial with a thin iron sheet or knife to open the back cover of the watch.

3.When you remove the fixing ring, you can see the various movements and other parts inside the watch.

4.Remove the whip and press the indentation with tweezers, then pull outward, being careful not to pull it as you pull.

Then you can remove the table cover.

But it is still recommended that you find a professional to disassemble it.

Hello dear, happy to serve you, I hope my answer can help you, Xi.

I hope I can like it, and please automatic.

End of service, currently the platform can only consult once.

It is not recommended to ask the same question more than once.

Different questions, if you want to ask different questions.

For the consultation of the question, it is recommended that you can click on the Lord.

page, consult separately, thank you

Look at the hollow place, and then hit it clockwise with a nail or something, or if it's not right, knock it in reverse. It came down in a few clicks.

The back cover of the watch, it has a special tool to open, if you don't have that tool, it is difficult to open it at home. If you want to open the back of your watch, please visit a watch shop and they will open it for you at no charge.

Hello landlord, the back cover of the watch is opened with the help of tools, you can't open it if you don't have tools, you can go to the watch repair shop to open it.

Hello, how to open the back cover of the watch, you first see if there are any small screws, if there are any, it will be easy to do, if not, you may need to go to a special place to repair the watch to see.