Sigma 506 computer settings, how to adjust the sigma 506 computer The simplest kind ? Bicycles

BC506 bicycle computer has a certain number in our riders, but because its manual is in foreign languages, it is inevitable that there are some difficulties in reading, which affects the correct realization of the function of the computer.

Sigma BC506 Bicycle Computer Instructions for use.

Function introduction. 1. It can display speed, riding distance (up to 99,999km), riding time (up to 999:59 hours), cumulative riding mileage (up to 99,999km), clock function.

2. Manual and automatic display function. Auto display, when the auto display function is turned on, the riding distance, time, total mileage and clock can be displayed sequentially at intervals of 1 second.

Here's a quick rundown of how to use it:

1. Function display.

1. Automatic display. Press the function button (the large button below the computer) until the word auto appears, and the computer will automatically display the riding distance, time, total mileage and clock at intervals of 1 second.

2. Manual display. Press the function button, and the word km appears, indicating that the travel distance is displayed at this time;

Press the function button, and the alarm clock pattern appears, indicating that the travel time is displayed at this time, which is accurately displayed to the second;

Press the function button, and the word "" will appear, indicating that the cumulative riding distance from the time the computer is installed is displayed at this time.

3. The code meter is cleared. Press and hold the function button for no less than 3 seconds, at this time, the number on the computer flashes, continue to press and hold until it is cleared, and the clearing will not affect the cumulative riding distance.

2. Settings. This function determines the correct use of the computer and is very crucial. The main functions are to enter the wheel circumference, adjust the clock, change the speed unit, turn on the automatic display function, etc.

Enter the settings interface. Press and hold the setting button on the back of the computer for 3 seconds, the word set appears, that is, to enter the setting interface, at this time, the four digits displayed below are the circumference of the wheel, at this time, press the function button, and the setting interface of the next function will be entered.

The following describes how to use this function by setting the wheel perimeter as an example.

Under the setting interface, press the setting button, the number on the computer will start to flash, indicating that you can enter the number at this time, press the function button, the flashing number will change, my tire is 32-630, you should enter 2 in the first digit, wait for the second digit to flash, press the function button, enter 1 in the second digit, and enter 9 in the third and fourth digits in turn, that is, the perimeter is 2199.

According to the above method, you can adjust the clock, etc., and do not repeat it because of the same method.

Exit the settings screen. Press the setting button for 3 seconds to return to the usable state.

<> "Sorry, I'm not a researcher, I can't provide an answer about the Sigma 506 meter setup, I encourage you to check the relevant or contact Sigma Corporation for more accurate information."

1. Press the function key to select "Set the Rim" Press the setting key to adjust, the value that can be adjusted will flash at this time, press the function key to adjust the value, and the value will automatically jump into the next item when it flashes for the third time

This section describes how to use this function by setting the wheel perimeter as an example.

In the setting interface, press the setting button (i.e., the set button behind the computer), the number on the computer will start to flash, indicating that the number can be entered at this time, press the function button, the flashing number will change, and then enter the tire circumference. The tire circumference of 26* is 2080

Enter 2 0 8 0 in the first to fourth places respectively Note: Due to the consideration of inflation, weight and other reasons, the circumference of the actual riding may change, so it is recommended that people ride on the bike, walk a lap on the ground to measure the circumference of the best hope to adopt, thank you.

I'm sweating, and the speed doesn't change, that's the problem of the sensor head! What is the use of a meter?

Check the condition of the sensor head (whether it is aligned) and adjust it until there is a response through the sensor head computer meter!

Bicycle computer and how to set up the Sigma 509:

Press the "set" button until the setting function is displayed (set starts flashing).

1.Measure the wheel diameter Use the tablec, wheel size chart to determine the size of your wheels. There are two options: enter a numerical value or calculate to determine the wheel size [or .

2.Set the wheel size Press "mode" to switch the screen to the size screen Press "set" briefly to start flashing, press "mode" button to confirm the value, press "set" to move to the next number. After setting the value, press the "set" button to confirm.

Set OK appears.

3.Set kilometers to miles and switch to unit using "mode". Press "set" briefly, kmh will be displayed on the screen, and the screen will flash.

Use "mode" to select MPH or KMH, press the SET button to confirm. Set OK appears. When switching from KMH to MPH, the distance format will automatically switch from KM to MI and the time format will also switch from 24h to 12h.

4.Set the total riding distance Press "mode" to switch the screen to dist. Press the "set" key briefly and the first digit starts flashing.

Use "mode" to set the value Press "set" to jump to the next value. After setting the value, press the "set" button to confirm. Set OK appears.

5.Set the time Press "mode" to switch the screen to time. Press the "set" key briefly and the "hour" hour will start flashing.

Press "mode" to set it"times"。Press the "set" button briefly to set"points"。Use "mode" to set the value After setting the value, press the "set" button to confirm.

Set OK appears.

6.Set the auto-browsing mode Press "mode" to switch the screen to scan. Press the "set" button briefly to display the OFF button on the screen Press the "mode" button to set the ON or OFF button and press the "set" button to confirm.

Set OK appears. Scan On auto mode automatically changes the screen display every three seconds.

7.Leave Basic Settings Press "set" for 3 seconds to stop the basic settings. (set close flashing) Reset Press "mode" until the desired function appears Press "mode" on the screen to flash, after 4 seconds, the ride distance and ride time will reset to zero.

Shows the total distance you've ridden since you started using this computer and can't be cleared unless the battery is replaced.

This ** can be lowered to the manual. It's a pdf, so I can't send it to you here.

Attach it to the car and put the speedometer on the spokes and forks.

Is the magnet of the speedometer too far away from the receiver?

The ATX series are all 26-inch wheels. There is a wheel size setting table in the manual. Set the wheel diameter ** to the corresponding ** of 26-inch tires and it is OK.

The manual is set to 2089, but it is set to 2075, which is related to the deformation of the tire under compression. In fact, it doesn't need to be set up too accurately.

For 26* tires, the wheel circumference should be 2055 mm on the computer.

In fact, it is not necessary to be very precise, you can check the sigma manual, which has a list that tells you what size of wheels to use and what is the rim size.