How Vista and XP connect to a local area network

All three use an unlimited network card! After installing the driver, the search network will be displayed in the lower right corner, and you can find the network by clicking on the search (of course, the wireless route must be turned on).

1. First turn on the computer, click the start icon button in the lower left corner of the computer desktop, click to open "Run" in the pop-up menu bar, or press the key combination "Win+R" to open the running window.

2. Then click to enter the IP of the LAN in the pop-up window, that is, the real IP address of the shared computer.

3. Then in the pop-up window, I successfully logged in to the win7 computer shared folder. Double-click the printer icon in it.

1. The production of network cables.

Before connecting to the network, the first thing we should consider is the production of the network cable. Generally, if you use twisted pair to build a network, you need a hub (hub), when you connect the network through the hub, the clamping method of twisted pair is very easy, just clamp the network cable at both ends one by one, the clamping order is the same on both sides, and the unity is: 1, white orange, 2, orange, 3, white green, 4, blue, 5, white blue, 6, green, 7, white brown, 8, brown.

Note that both ends are in the same line order and correspond one-to-one. This is the standard for making 100m network cables, that is, the 568b standard, which is what we usually call the positive line or standard line.

However, as a small network with only two machines, it is a bit too wasteful to buy a hub of several hundred yuan, in fact, we can directly connect the two computers with a network cable without a hub, but at this time, the practice of network cable should have some small changes, and the dual-machine interconnection without a hub is realized by changing the order of the network cable. The specific method is: one end adopts the above-mentioned 568b line standard unchanged, and the other end will swap the positions of line 1, line 3 and line 2, line 6 of the eight lines on this basis, and then the line sequence of the network cable becomes:

1, white-green, 2, green, 3, white-orange, 4, blue, 5, white-blue, 6, orange, 7, white-brown, 8, brown. This is the 568A standard of 100m network cable, which is what we usually call the reverse line or intersecting * line. After arranging the wire sequence according to the standard of 568B at one end and 568A at one end, and clamping it, a network cable suitable for direct connection of two computers is ready.

How to configure: The workgroup should be the same on both computers, e.g. both workgroups.

Subnet mask""

Default gateway""

Write the IP address on the second computer""

The subnet mask is the same.

Default gateway""

It's very simple.

Just set the IP.

For example, the IP addresses of the two machines are set to :

Subnet Mask: Default Gateway:

DNS servers do not need to be set up.

If your computer is a 100 Gigabit network card, you need a crossover network cable, and ask the other party to make a crossover cable when you buy it.

If your computer has at least a Gigabit network card, your network cable can be either straight or crossed.

You can set the IP on the side of the network card.

The five-port switch is estimated to be 40 yuan, and the router is about 60 yuan, and you don't have the money to buy it!!

Use a crossed network cable. 568a on one end and 568b on the other end Set the IP address of the unified network segment to find a folder to share. Access that shared machine. It should be fine.

In general, if two operating systems are installed successively, the latter operating system may be automatically configured with a dual-boot boot option.

Older operating systems, such as Windows, are usually installed first

XP, which was later installed on a newer operating system such as Windows

vistahome

basic.After installing Vista in this way, Vista can automatically configure both its own and XP's dual boot options.

The reverse is usually not possible, for the simple reason that Vista can recognize the existing XP in the system, and XP can't recognize Vista, think about the time of birth.

For example, if you configure Windows98 and WindowsXP dual boot, then you must install Windows98 first and then XP, but it should be emphasized that XP is required"Installation"If it's a ghost version, it's almost impossible to automatically configure it for dual boot. Because the Ghost version of XP works by forcibly writing to C"The final installation has not yet been completed"XPThis skips the step of making XP recognize the drive's legacy system in the first place, so it cannot be configured.

So in this case, it's best to install Windows in the regular way on the G drive first

XP, and then install Vista on the C drive, so that the Vista installation process can be automatically configured with the dual boot option of Vista and XP.

By the way, I personally do not approve of a computer using more than one operating system, such as XP and Vista for NTFS file format disk partitions, there are certain differences in the way they are managed, and the permissions are not exactly the same, if you do not know the permissions very well, the use will cause unnecessary trouble in some cases.

Yes, but keep in mind the following conditions.

1.Install XP first, then Vista. Otherwise fix the boot menu as well.

2.To reboot the system into the BIOS settings disc boot in the installation, if not reboot will upgrade the XP to Vista.

3.Do not place two systems in one volume.

There's nothing wrong with that, it's just not necessary. It's better to install XP first.,If you install Vista first and then install XP, you need to boot it.,It's not very troublesome to boot.,You can search on the Internet.。

Absolutely, assuming that the XP system is C drive, then the Vista system is set to D drive, if you want to remove one, just format a partition drive letter.

OK. However, when installing, you need to install XP first and then install Vista's system.

Otherwise, an error will be reported.

Also, when you have two systems, you must ensure that they are not in the same partition!

Enter the battle platform Warcraft to the same version, and then build a good house, wait for someone to come If you only need two machines, it's very troublesome, so don't talk about it.

On the Hao side battle platform company,As long as the game version is the same。

You can experiment with using XP as a host.