What should I do if the router settings connection fails?

There are many problems with the router setting connection, and the question does not describe what the problem is, and the problems are caused by incorrect settings

1. After connecting the wireless router, enter the address you see on the back of the router in your browser.

2. After entering, you will see that you enter the corresponding account and password, and generally the newly purchased ones are admin.

3. After entering the operation interface, you will see a setting wizard on the left, and you will enter it.

4. Enter the interface of the setup wizard.

5. Click Next to enter the Internet access mode settings, and you can see that there are three Internet access options, and PPPOE is selected for families.

6. If you choose PPPoE dial-up Internet access, you need to fill in the Internet account and password, and enter the user name and password provided by the operator.

<>7, and then the next step is to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in casually, and then the mode is mostly 11BGNThe wireless security option is WPA-PSK WPA2-PSK, which is safe and will not be cracked and rubbed by others.

8. The next step is to set it up successfully.

9. Click Done, and the router will automatically restart.

There are the following workarounds:

1. Try or try to log in to the router with the same IP as your company's gateway, or observe whether the router is damaged.

2, or you see if the network card is stopped, sometimes sleep will deactivate the network card. Local Connection Properties Configure Power Management to remove all hooks and then restart.

3. Or boot the network card from the BIOS.

Fault Symptom:There is no problem with the router hardware, and there is no problem with the connected computer, but it cannot achieve a normal connection, while other computers in the LAN can connect to the Internet normally.

Cause of failure:This is generally due to the inability to connect due to the binding MAC address of the ISP, because some ISPs bind the MAC address on the authentication server in order to limit the number of access users, and users who are not within the bound range cannot connect to the Internet normally.

Workaround:First, connect the computer bound to the MAC address to the LAN port of the router (but the router should not connect the Wiring provided by the Modem or ISP), and then use the MAC address cloning function of the router to clone the network card'Copy the MAC address to the WAN port of the broadband router, and then perform the following operations on the unbound computer: press "Start Running" under Windows 2000 XP, and enter "CMD Kipconfig All", where "PhysicalAddress" is the local MAC address.

Fault Symptom:Unable to log in to the broadband router settings page.

Causes and how to fix them:

First, make sure that the router is properly connected to the computer. Check whether the indicators corresponding to the NIC port and the LAN port of the router are normal.

If the indicator is not normal, plug the network cable back in or replace the twisted pair cable, and then check the network connection in the computer: first set the IP address of the computer to automatically obtain the IP address. Then check whether the connection of the network card correctly obtains the IP address and gateway information, if not, please set it manually, if this information has been obtained correctly, please pay attention to whether the firewall service is enabled, if it is enabled, please disable it.

Newer routers (especially home ones) are mostly maintained by IE login routers, so we can select "Never dial-up connection, then click" LAN settings in IE's connection settings to clear all options. Then enter the IP address of your broadband router in the address bar of your browser and press Enter to enter the settings page. If you still cannot log in, try setting the gateway to the IP address of the router and the IP address of the machine to the IP address of the same network segment as the router before connecting.

If the above methods do not solve the problem, please check whether the NIC conflicts with other hardware of the system.

Fault Symptom:It is not uncommon for you to be unable to connect to your router or have a very slow connection.

Causes and how to fix them:

This situation has a lot to do with the network cable. If there are frequent connection problems, there may be quality problems or contact problems with the crystal head, so pay attention to plugging in the various interfaces tightly. And replace the *** crystal head. Also check whether the network cable is in the correct line sequence.

Fault Symptom:Use ADSL to surf the Internet, but after setting up the router, you can't use dialing software to dial up.

Causes and how to fix them:

After setting up the PPPoE connection of the router, you can dial from the router, no need to use the dialing software in the computer, as long as the IP address of the computer is set to "automatically obtain or set to the IP address that does not conflict with the router."

Fault Symptom:The router was unable to obtain a WAN address.

Causes and how to fix them:

First of all, please check whether the WAN port indicator of the router has been lit, if not, there is a problem with the network cable or crystal header. Then check if the router has been configured correctly and save the reboot, otherwise the settings won't take effect! In some cases, you may need to clone the MAC address of the NIC to the WAN interface of the router, please refer to the router manual for specific settings.

Your question involves network and computer hardware, and the following is an analysis of several possibilities for you

1. Routing. 1) Routing is automatically restarted.

You can check the route configuration, restart the route, check the port of the routing LAN, and change the port.

2) Network cables.

For example, there is a problem with the network cable used, and the RJ45 crystal head is loose (3) computer hardware.

For example, the network card is not in good contact, the motherboard has a problem, etc., which may cause the display to be unable to connect (4) virus.

I don't think I need to explain this.

There are all these possibilities, and you need to carefully check this step by step.

Good luck! Know the team: network equipment DIY

Computer problems. The computer has a virus.

Take a look at the LSP repair with the 360 tool.

There is a problem with the computer. Is it like that for both computers?