Subject 3: When you get into the car, do you lift the clutch first or release the handbrake first?

Road test subject 3: When parking, you should first release the handbrake and then release the clutch to start.

The steps to park properly are as follows:

1. After the examiner issues the instruction to pull over, observe whether the road ahead is a curve, intersection, bridge, gas station or tunnel, if there is, you must pass before you can find a place to park in a suitable location, because these places cannot be parked.

2. Turn the right turn signal, turn your head slightly to look at the right mirror;

3. Step on the clutch (step on the clutch first during the driving test to avoid the novice handling experience caused by the stallion, the actual driving should be stepped on the brake first, and then the clutch should be stepped on after the speed drops, so as to avoid the brake wear out too fast, but also safer);

4. Step on the brakes;

5. The vehicle drives to the right to a suitable parking position;

6. a brake; 7. The gear is dialed back to neutral;

8. loosening the clutch;

9. pulling the handbrake;

10. Release the brakes.

First, the essentials of starting, adjust the seat after getting on the bus, and fasten the safety belt. Put the gear in neutral, ignition, turn on the left direction light, switch to the first gear, and release the handbrake! Look at the left mirror and start slowly with your foot on the clutch.

3. When there are obstacles on the road, if the speed is above three gears, you must step on the brake first and then step on the clutch, not the clutch first! Then switch gears again according to the situation. In the test, if the examiner prompts you to make a U-turn, the first step is to turn on the turn signal, and be sure to switch to second gear.

OK. Kesan can start without stepping on the brakes and directly lift the clutch slowly. Immediately lift the clutch slowly, which can easily cause the vehicle to slip backwards.

Stepping on the brake pedal development is to prevent your vehicle from slipping backwards or rushing forward, you don't want to step on the brake pedal to develop, but you are worried that the car will stop the fire, after all, the novice is very bad for the clutch work ability, but remember to be forced to step on the brake pedal to develop.

If you start on an uphill road, you have to keep pressing the brakes until the clutch is loose to the semi-linkage, and then keep the clutch when the front of the car is tilted upward, and then release the brakes, lightly press the accelerator, and the car will walk up and will not slip.

Subject 3 Skills:

1. Pay attention to the process when preparing for the car, first report to the examiner, and then request a car inspection, and then pay attention to the action, because there may be a camera, if the action is not in place, you may be directly judged to be unqualified, so pay attention to the action in place, and get on the car at the end of the inspection.

2. When starting, follow the light gear brake smoothly, so that you will not forget the smooth, slightly lift the clutch when starting, and prevent the motor vehicle from turning off directly, so remember to lift it slightly, and then hang a gear, and start smoothly.

3. When passing through the crosswalk, bus stop, or school area, pay attention to deceleration and downshift in advance, and then bring three to five seconds of braking when you get to the place you say, and then add some throttle to continue to complete the next test.

OK. Kesan can start without stepping on the brakes and directly lift the clutch slowly.

Immediately lift the clutch slowly, which can easily cause the vehicle to slip backwards. You don't want to step on the brake pedal to develop, but you are worried that the car will stop burning, after all, the novice is very bad at the clutch work ability, but remember to be forced to step on the brake pedal to develop.

If it is developed on the slope, you need to keep pressing the brake pedal until the clutch is loose to semi-linkage, and the clutch is maintained when the car is upturned, and then let go of the brake pedal, lightly refuel, and the car will walk up, and it is not easy to slip.

Precautions. 1.After the fingerprint verification fails, please get off the bus and re-collect the finger lines before queuing up again for the test.

2.During the test, if the candidate's score is lower than the passing score, the system will automatically prompt the candidate to pull over, and the system will prompt the candidate to enter the next test after the pullover action is completed.

3.After the test taker completes all the required items and the driving distance is greater than 3 kilometers, the system will automatically prompt them to pull over. After hearing the sound of pulling over, students should choose a clear curb stone (or solid line on the edge of the road) on the test route, confirm that it is safe to complete the pullover action.

After the pullover is completed, the system will announce the test result by voice.

Ke San starts to release the brakes first, then loosen the clutch semi-linkage, and then release the brakes all:

1. When starting to start, the clutch of the left foot is slowly lifted to nearly half, and when you feel that the vehicle is shaking, release the handbrake in time;

2. Then gently tap the throttle, slowly release the clutch when the car wants to move forward, and then add a little throttle to start successfully;

3. If you are a novice at the start of the ramp, you should pay special attention, if you release the handbrake quickly, and the clutch is not lifted in place, it is easy to slip. The best way to do this is to press the clutch and brake when starting, and the handbrake can be used or not. When the clutch is lifted to the halfway point, release the brake, at this time the vehicle is in a semi-clutch state, the car will not slip back, and at the same time add the throttle, slowly release the clutch, and the start is successful.

You need to release the brakes first, put down the handbrake, and then release the clutch. It should be noted that the clutch should not be released too quickly, and the semi-linkage state of the clutch must be found, otherwise it is easy to have a stalling problem, which is very important for throttle clutch coordination, but it requires more practice.

Subject 3 examines the role of the clutch.

The role of the clutch is to shift gears. When the vehicle reaches a certain speed, the clutch needs to be pressed all the way down to change the gear of the vehicle. When the vehicle needs to slow down, you need to buy the first clutch of the vehicle, reduce the gear of the vehicle step by step, and control the vehicle clutch to reduce frustration.

What does it take to get started with the Subject 3 exam?

When starting, you need to turn on the left turn signal and look for a car behind the left rearview mirror. If there is a car behind, you need to wait for the backstage to pass. Then, when the vehicle starts, don't start too fast. After normal start, you can move the vehicle to second gear and listen to the relevant instructions.

Millions of car purchase subsidies.

Let go of the handbrake first. When driving a manual transmission car, the oil should be well coordinated when starting. In a normal start, it is required to start smoothly and safely, and to have a correct driving posture.

When starting, you should pay attention to the gear selection, which should be selected according to the specific conditions of the car, the road and the slope. Generally, on a flat, solid road or field, you should choose 1st or 2nd gear to start.

After starting the engine, listen to its operation and observe the instructions of each instrument. After the engine starts and runs normally, after confirming that there is no obstacle around the car and has all the conditions for the car to start, press the clutch pedal to the end with your left foot to completely disengage the clutch.

There is no need to step on the brakes when starting on a flat road, and when you need to start with brakes, you can start on a sloped road surface to prevent rolling.

Start, the scattered person steps on the clutch, slowly lifts the clutch, feels that the car is going to go, has the feeling of rushing forward, lightly steps on the accelerator, stops, first steps on the brakes, the speed is reduced, and the clutch is stepped on the end at the same time and the brake is stepped on until the car stops.

When braking suddenly, you should only step on the positive brake and not on the clutch, because when you step on the clutch and then on the brake, you will lose engine traction, resulting in a longer braking distance and increasing potential safety hazards.

The result of only stepping on the brake and not stepping on the clutch is bound to be stalled, although the braking distance has not changed, but there is the possibility of a secondary accident after braking, if you turn off when the second danger comes, you want to escape and have to go out of a few extra operation steps of time, which is also a safety hazard.

In an emergency, people are in a highly nervous state, especially for people with poor sense of machine operation, it is likely that the pedal will be misoperated in a panic, if the brake and clutch are pressed at the same time, even if the accelerator is stepped on by mistake, it will not affect the braking effect.

According to the data, the average distance between the clutch and the brake at the same time is 7cm shorter than that of just applying the brake, of course, this difference can be regarded as the same effect, and there is basically no change.