How to configure a laptop that requires it to run software such as Pro E?

In fact, the current general configuration is OK, but it requires a discrete graphics card

The operation of the game is directly related to the hardware configuration of the machine, such as CPU, memory, and independent display core, as well as the system, drivers, and other software. At present, whether you can play a game, you first need to check the configuration requirements of the game and the configuration requirements of the machine to make a comparison to see whether the configuration of the machine is compliant. If the minimum running requirements of the game can be met, it can be supported. "

1. Network factors: This game is a 3D game, and the requirements for the network are relatively high! From the point of view of solving the problem for a long time, it takes at least 2M bandwidth to play and run!

But good fluency is required, preferably 4m! If you're not 4m, offer some advice and you should be able to alleviate it! If your operating system is XP Pro, then you can:

RunRunThis game is a 3D game, and the requirements for the network are relatively high!

From the point of view of solving the problem for a long time, it takes at least 2M bandwidth to play Run, but it needs a good fluency, preferably 4M, if you are not 4M, provide some suggestions, it should be able to alleviate it!

At the very least, the computer must be the Internet platform, the Pentium series dual-core or above, the CPU memory is at least 2G, the brand and model are not so harsh, the gap is not big, the graphics card must be independent, 512 or more, the hard disk is 160G, it is enough, the notebook with such a configuration needs about 5000, and the 3000 of the desktop is not used up

Will you understand anything about this introduction?

I also use the above software.

The current mainstream notebook runs these software without any problem, of course, it is a separate display, if you don't consider the cost, naturally choose the best!

In addition, if you have a particularly professional need, you should also consider the workstation!

What is the key 3DMAX version, the higher the version, the higher the requirements, even if it is a 1G graphics card, 4G memory, the same card for 3DMAX2010 large-scale rendering, it is recommended to contact IdeaPad Y550A PSE(W) (gray), official** 6299, 1G graphics card, 4G memory, Core 2 dual-core, but Windows 7 system for software, temporarily estimate that the compatibility is a bit of a problem. If you want to be a little cheaper, buy IdeaPad Y450A TSI(E) (white), 2G memory, 512M independent graphics card, the processor is the same as above, the cost performance is absolutely high, but the workmanship seems to be average, and this is a DOS system, and there is no problem with compatibility after installing XP.

Processor: minimum i5

RAM: 4G minimum

HDD speed: 7200 min

Graphics card: Minimum 1G for a dedicated graphics card, and a conditional SSD can be added. (Graphics card graphics processing) to meet these your notebook can definitely pull.

Cost-effective, HP Acer Dell you can refer to.

It is recommended to buy Acer's cost-effective I bought it myself for 3000 Running CAD2014 is no problem Other software is not very clear.

Dell Ranger, i5 4G 500G independent display can definitely be 4688 yuan.

5000, can buy i7, enough. Yes, it works. The brand recommends ASUS, DELL.

Did you study mechanical design?

Now the notebook configuration is very good, more than 3500 to run you these are basically no problem.

i5 processor or above, 1G video memory or more, 4G memory or more is enough. And these configurations are the mainstream configurations now.

I recommend you a few of the best.

1.ASUS A550JK4200

2.Dell Inspiron 15 5000 (INS15MD-1528S).

3.Lenovo Y430

These two computers are about 4600 yuan, and the one I bought for my brother is the first one, 4580 to start.

These two are enough for your software.

If you want to buy a good one again.

ASUS FX50JK4200 is recommended

I personally don't like Lenovo, it's ugly.

For a general design, the mainstream configuration is perfectly fine. However, if it is often used for advanced operations such as force analysis, motion simulation, and special effects rendering, it is recommended that the configuration be higher (at least 6000 yuan or more).

The main point,Discrete graphics card,And it's big enough,,Mine is a discrete graphics card,,, it's no problem to run a general solidworks pro e,It is recommended that you get a 512.。。。 Play casually like this.

ug is to configure the high point·· It must be a discrete graphics card 256, the memory should be larger 2G, and nothing else!! UG has the highest requirements for the computer, as long as you can get the ug, Pro E is naturally not a problem China Precision Mould Network professionals will answer for you, I hope it will help you!

The present book. Any one that is not less than 4000 can run perfectly.

I bought the ACER 3205 7200 3 years ago, and it was only 512MB of RAM at that time, and the AMD3300+ ATI-X600 was designed with the same PROE and UG.

It is recommended to use AMD ATI graphics card for graphics. Now the HD 3450 is basically competent,**In 4000-6000 looks。

These are not important, but you must use the Internet or a virtual network card to use them.

The Pro E software is not very demanding on the computer.

Anything should work.

In a high configuration, do PR plus effect will be stuck. You can only see the full effect after rendering. Multi-project memory is best used as much as possible. The graphics card is still going to be high. It's a sure thing that doesn't work well when making PRs. It's true that rendering can be sped up.

As required on the Pro E software, the configuration is indeed very low. Mainly the graphics card, the integrated graphics card I installed before, the integrated HD3200 chip, still drawing, no problem, but the large online game graphics card is not good. What is the configuration of your computer, install it yourself and try it.